摇摇棒的详细制作资料和实例程序代码（谁看谁会）

摇摇棒的详细制作资料和实例程序代码（谁看谁会）摇摇棒的详细制作资料和实例程序代码（谁看谁会） LED摇摇棒的详细制作资料【图】大家知道，人的眼睛存在视觉暂留现象，正因为眼睛的反应迟钝，才丰富了人的视觉感受。 LED摇摇棒很好地利用了人眼的视觉暂留特性。下图是基于51单片机控制、16只高亮度LED发光二极管构成的摇摇棒，配合手的左右摇晃就可呈现一幅完整的画面，可以显示字符、图片等。演示效果见自制LED摇摇棒展示【图】。实物外形图(点击可放大): 基本原理与硬件电路设计: 16只LED发光管作为画面每一列的显示，左右摇晃起到了扫描的作用，人眼的...

摇摇棒的详细制作资料和实例程序代码（谁看谁会） LED摇摇棒的详细制作资料【图】大家知道，人的眼睛存在视觉暂留现象，正因为眼睛的反应迟钝，才丰富了人的视觉感受。 LED摇摇棒很好地利用了人眼的视觉暂留特性。下图是基于51单片机控制、16只高亮度LED发光二极管构成的摇摇棒，配合手的左右摇晃就可呈现一幅完整的画面，可以显示字符、图片等。演示效果见自制LED摇摇棒展示【图】。实物外形图(点击可放大): 基本原理与硬件电路设计: 16只LED发光管作为画面每一列的显示，左右摇晃起到了扫描的作用，人眼的视觉暂留现象使得看到的是一幅完整的画面。与LED点阵的显示有几分相仿。硬件电路如下图(点击可放大)。系统电源VCC为5V，下载程序和调试时一定要保证5V电压，实际使用时用3节干电池串联4.5V即可。AT89S52单片机作为控制器，在它的P0、P2口接有16只以共阳的方式连接的高亮度LED，由单片机输出低电平点亮。P0口的上拉电阻RA1不能少。串在LED公共端的二极管D1会产生一定的压降，用来保护LED，经实测LED点亮时两端电压为3V左右，在LED的安全承受范围内。K1是画面切换开关，用于切换显示不同内容;S1为水银开关。水银开关的作用:棒在摇动时，只能在朝某一方向摇动时显示，否则会出现镜像字或镜像画面，所以通过接一只水银开关来控制，使摇摇棒从左向右摇动时将内容显示出来。硬件制作: 使用的是直径5mm的红色高亮LED，感觉太大了些，远看效果很好但近看时字不够连贯。建议使用直径为3mm的高亮LED，颜色可根据个人喜好选择。水银开关里的水银珠很活跃，导致在接通时容易产生抖动，所以将水银开关斜向上放置(尖尖朝斜上方45?角)，靠水银珠自身重力的作用减少抖动: IC座里面隐藏元件，既美观又能保护元件: 软件设计: /********************************************************** 程序名称:LED摇摇棒显示64*16像素简要说明 :外部中断方式INT0显示;取模方式:纵向取模、字节倒序编写:JiangX.net 最后更新:08/11/15晚 **********************************************************/ #include #define usher unsigned char #define uint unsigned int //宏定义 #define KEY P3_0 //定义画面切换按键 uchar KY; //KY作用在后面说明 uchar disp; //显示汉字指针 uchar pic=0,num=0; //pic为按键次数;num为中断次数 uchar code love[] = { 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x3F,0x00,0x20,0x00,0x20,0x00,0x20, 0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0xF8,0x0F, 0x04,0x10,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x04,0x10,0xF8,0x0F,0x00,0x00, 0x00,0x00,0x00,0x00,0xFE,0x07,0x00,0x08,0x00,0x10,0x00,0x20,0x00,0x20,0x00,0x10, 0x00,0x08,0xFE,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x3F,0x82,0x20,0x82,0x20, 0x82,0x20,0x82,0x20,0x82,0x20,0x82,0x20,0x82,0x20,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*LOVE*/ }; uchar code loveyou[] = { 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x78,0x00,0xFC,0x00,0xFE,0x01,0xFE,0x03,0xFE,0x07,0xFE,0x0F,0xFE,0x1F,0xFC,0x3F, 0xF8,0x7F,0xFC,0x3F,0xFE,0x1F,0xFE,0x0F,0xFE,0x07,0xFE,0x03,0xFE,0x01,0xFC,0x00, 0x78,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*心形图案* / }; uchar code hehe[] = { 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0x01,0x40,0x01,0xC0,0x01,0x00,0x00,0x00,0x00, 0xF0,0x0F,0x08,0x10,0x04,0x20,0x00,0x00,0x00,0x00,0xF0,0x3F,0x08,0x00,0x04,0x00, 0x04,0x00,0x04,0x00,0x08,0x00,0xF0,0x3F,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x20, 0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x00,0x00,0x00,0xF0,0x3F,0x08,0x00,0x04,0x00, 0x04,0x00,0x04,0x00,0x08,0x00,0xF0,0x3F,0x00,0x00,0x00,0x00,0x04,0x20,0x08,0x10, 0xF0,0x0F,0x00,0x00,0x00,0x00,0xC0,0x01,0x40,0x01,0xC0,0x01,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*呵呵o(?_ ?)o图案*/ }; unsigned char code hanzi[] = { //-- 欢 -- 0x04,0x10,0x34,0x08,0xC4,0x06,0x04,0x01, 0xC4,0x82,0x3C,0x8C,0x20,0x40,0x10,0x30, 0x0F,0x0C,0xE8,0x03,0x08,0x0C,0x08,0x10, 0x28,0x60,0x18,0xC0,0x00,0x40,0x00,0x00, //-- 迎 -- 0x40,0x00,0x42,0x40,0x44,0x20,0xC8,0x1F, 0x00,0x20,0xFC,0x47,0x04,0x42,0x02,0x41, 0x82,0x40,0xFC,0x7F,0x04,0x40,0x04,0x42, 0x04,0x44,0xFE,0x63,0x04,0x20,0x00,0x00, //-- 使 -- 0x40,0x00,0x20,0x00,0xF8,0xFF,0x07,0x00, 0x04,0x80,0xF4,0x43,0x14,0x45,0x14,0x29, 0x14,0x19,0xFF,0x17,0x14,0x21,0x14,0x21, 0x14,0x41,0xF6,0xC3,0x04,0x40,0x00,0x00, //-- 用 -- 0x00,0x80,0x00,0x60,0xFE,0x1F,0x22,0x02, 0x22,0x02,0x22,0x02,0x22,0x02,0xFE,0x7F, 0x22,0x02,0x22,0x02,0x22,0x42,0x22,0x82, 0xFF,0x7F,0x02,0x00,0x00,0x00,0x00,0x00, //-- 神 -- 0x08,0x01,0x88,0x00,0x49,0x00,0xEE,0xFF, 0x58,0x00,0x88,0x00,0x00,0x00,0xF8,0x1F, 0x88,0x08,0x88,0x08,0xFF,0xFF,0x88,0x08, 0x88,0x08,0xFC,0x1F,0x08,0x00,0x00,0x00, //-- 奇 -- 0x40,0x00,0x40,0x00,0x44,0x00,0x44,0x3E, 0x64,0x12,0x54,0x12,0x4C,0x12,0x47,0x12, 0x4C,0x3F,0x54,0x42,0x74,0x80,0xC6,0x7F, 0x44,0x00,0x60,0x00,0x40,0x00,0x00,0x00, //-- 魔 -- 0x00,0x40,0x00,0x30,0xFE,0x8F,0x4A,0x80, 0xAA,0x5F,0x9A,0x4A,0xFE,0x2A,0xAA,0x1A, 0xCB,0x0F,0xAA,0x7A,0xFE,0x8A,0x9A,0xAA, 0xAA,0x8F,0x6B,0x80,0x22,0xE0,0x00,0x00, //-- 幻 -- 0x80,0x20,0xC0,0x30,0xA0,0x28,0x98,0x24, 0x87,0x22,0x80,0x21,0xC4,0x30,0x04,0x60, 0x04,0x00,0x04,0x20,0x04,0x40,0x04,0x80, 0x04,0x40,0xFE,0x3F,0x04,0x00,0x00,0x00, //-- 摇 -- 0x10,0x02,0x10,0x42,0x10,0x81,0xFF,0x7F, 0x90,0x04,0x54,0x05,0xCC,0xF4,0xB4,0x44, 0x84,0x44,0xBC,0x7F,0x82,0x44,0xA2,0x44, 0x9B,0xF4,0x82,0x06,0x00,0x04,0x00,0x00, //-- 摇 -- 0x10,0x02,0x10,0x42,0x10,0x81,0xFF,0x7F, 0x90,0x04,0x54,0x05,0xCC,0xF4,0xB4,0x44, 0x84,0x44,0xBC,0x7F,0x82,0x44,0xA2,0x44, 0x9B,0xF4,0x82,0x06,0x00,0x04,0x00,0x00, //-- 棒 -- 0x10,0x04,0x10,0x03,0xD0,0x00,0xFF,0xFF, 0x90,0x00,0x54,0x05,0x44,0x12,0xD4,0x15, 0x74,0x14,0x5F,0xFF,0xD4,0x14,0x54,0x15, 0x56,0x12,0x44,0x06,0x40,0x02,0x00,0x00, //-- ～ -- 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x7C,0x10,0xFE,0x3B, 0xFE,0x3B,0x7C,0x10,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00 }; /*****函数声明*****/ void display1(void); void display2(void); void display3(void); void display4(void); /*****n(us)延时子程序*****/ void DelayUs(uint N) { uint x; for(x=0; x<=N;x++); } /*****中断服务程序*****/ void intersvr0(void) interrupt 0 using 1 { KY=~KY; //每个摇动来回水银开关会在摆幅两端分别产生下降沿中断，只提取其中一次(从左向右摇才显示) if(KY==0) { num++; //计算中断次数 switch(pic) //选择画面 { case 0:{display1();}break; case 1:{display2();}break; case 2:{display3();}break; case 3:{display4();}break; default:{display1();} } } } /*****显示子程序1(汉字)*****/ void display1(void) { uchar i; if(num>10){disp++;num=0;} //12个汉字分为3次显示完(每次显示4个)，每中断10次切换 if(disp>2)disp=0; DelayUs(5200); //此处延时时间依各硬件差别而各不相同，试着调整使得显示内容居中即可 for(i=0;i<64;i++) { P0=~hanzi[disp*128+i*2]; P2=~hanzi[disp*128+i*2+1]; DelayUs(100); } } /*****显示子程序2(LOVE)*****/ void display2(void) { uchar i; DelayUs(4000); for(i=0;i<64;i++) { P0=~love[i*2]; P2=~love[i*2+1]; DelayUs(120); } } /*****显示子程序3(心形图案)*****/ void display3(void) { uchar i; DelayUs(4000); for(i=0;i<64;i++) { P0=~loveyou[i*2]; P2=~loveyou[i*2+1]; DelayUs(120); } } /*****显示子程序4(呵呵o(?_?)o图案)*****/ void display4(void) { uchar i; DelayUs(4000); for(i=0;i<64;i++) { P0=~hehe[i*2]; P2=~hehe[i*2+1]; DelayUs(120); } } /*****主函数*****/ void main(void) { IT0=1; EX0=1; EA=1; //开中断，下降沿中断 KY=0; while(1) //主程序中只检测按键 { if(KEY==0) //画面切换键按下 { DelayUs(10000); //按键去抖 if(KEY==0); pic++;} if(pic>3)pic=0; } } /*****END*****/

                    本文档为【摇摇棒的详细制作资料和实例程序代码（谁看谁会）】，请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑，
                    图片更改请在作品中右键图片并更换，文字修改请直接点击文字进行修改，也可以新增和删除文档中的内容。 
 该文档来自用户分享，如有侵权行为请发邮件ishare@vip.sina.com联系网站客服，我们会及时删除。

                    [版权声明] 本站所有资料为用户分享产生，若发现您的权利被侵害，请联系客服邮件isharekefu@iask.cn，我们尽快处理。

                    本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权，请谨慎使用。

                    网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传，仅限个人学习分享使用，禁止用于任何广告和商用目的。
                

下载需要：免费已有0 人下载

立即下载

摇摇棒的详细制作资料和实例程序代码（谁看谁会）

你可能还喜欢