6N137

1-146 H High CMR, High Speed TTL Compatible Optocouplers Technical Data 6N137 HCNW137 HCNW2601 HCNW2611 HCPL-0600 HCPL-0601 HCPL-0611 HCPL-0630 CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. Features • 5 kV/µs Minimum Common Mode Rejection (CMR) at VCM = 50 V for HCPL-X601/ X631, HCNW2601 and 10 kV/µs Minimum CMR at VCM = 1000 V for HCPL- X611/X661, HCNW2611 • High Speed: 10 MBd Typical • LSTTL/TTL Compatible • Low Input Current Capability: 5 mA • Guaranteed ac and dc Performance over Temper- ature: -40°C to +85°C • Available in 8-Pin DIP, SOIC-8, Widebody Packages • Strobable Output (Single Channel Products Only) • Safety Approval UL Recognized - 2500 V rms for 1 minute and 5000 V rms* for 1 minute per UL1577 CSA Approved VDE 0884 Approved with VIORM = 630 V peak for HCPL-2611 Option 060 and VIORM = 1414 V peak for HCNW137/26X1 BSI Certified (HCNW137/26X1 Only) • MIL-STD-1772 Version Available (HCPL-56XX/ 66XX) Functional Diagram *5000 V rms/1 Minute rating is for HCNW137/26X1 and Option 020 (6N137, HCPL-2601/11/30/31, HCPL-4661) products only. HCPL-0631 HCPL-0661 HCPL-2601 HCPL-2611 HCPL-2630 HCPL-2631 HCPL-4661 Applications • Isolated Line Receiver • Computer-Peripheral Interfaces • Microprocessor System Interfaces • Digital Isolation for A/D, D/A Conversion • Switching Power Supply • Instrument Input/Output Isolation • Ground Loop Elimination • Pulse Transformer Replacement • Power Transistor Isolation in Motor Drives • Isolation of High Speed Logic Systems Description The 6N137, HCPL-26XX/06XX/ 4661, HCNW137/26X1 are optically coupled gates that combine a GaAsP light emitting diode and an integrated high gain photo detector. An enable input allows the detector to be strobed. The output of the detector IC is A 0.1 µF bypass capacitor must be connected between pins 5 and 8. 1 2 3 4 8 7 6 5 CATHODE ANODE GND V VCC O 1 2 3 4 8 7 6 5ANODE 2 CATHODE 2 CATHODE 1 ANODE 1 GND V VCC O2 VE VO1 6N137, HCPL-2601/2611 HCPL-0600/0601/0611 HCNW137/2601/2611 HCPL-2630/2631/4661 HCPL-0630/0631/0661 NC NC LED ON OFF ON OFF ON OFF ENABLE H H L L NC NC OUTPUT L H H H L H TRUTH TABLE (POSITIVE LOGIC) LED ON OFF OUTPUT L H TRUTH TABLE (POSITIVE LOGIC) SHIELD SHIELD 5965-3594E 1-147 an open collector Schottky- clamped transistor. The internal shield provides a guaranteed common mode transient immunity specification of 5,000 V/µs for the HCPL-X601/X631 and HCNW2601, and 10,000 V/µs for the HCPL-X611/X661 and HCNW2611. This unique design provides maximum ac and dc circuit isolation while achieving TTL compatibility. The optocoupler ac and dc operational parameters are guaranteed from -40°C to +85°C allowing troublefree system performance. The 6N137, HCPL-26XX, HCPL- 06XX, HCPL-4661, HCNW137, and HCNW26X1 are suitable for high speed logic interfacing, input/output buffering, as line receivers in environments that conventional line receivers cannot tolerate and are recom- mended for use in extremely high ground or induced noise environments. Selection Guide Widebody Minimum CMR 8-Pin DIP (300 Mil) Small-Outline SO-8 (400 Mil) Hermetic Input Single On- Single Dual Single Dual Single and Dual dV/dt VCM Current Output Channel Channel Channel Channel Channel Channel (V/µs) (V) (mA) Enable Package Package Package Package Package Packages NA NA 5 YES 6N137 HCPL-0600 HCNW137 NO HCPL-2630 HCPL-0630 5,000 50 YES HCPL-2601 HCPL-0601 HCNW2601 NO HCPL-2631 HCPL-0631 10,000 1,000 YES HCPL-2611 HCPL-0611 HCNW2611 NO HCPL-4661 HCPL-0661 1,000 50 YES HCPL-2602[1] 3, 500 300 YES HCPL-2612[1] 1,000 50 3 YES HCPL-261A[1] HCPL-061A[1] NO HCPL-263A[1] HCPL-063A[1] 1,000[2] 1,000 YES HCPL-261N[1] HCPL-061N[1] NO HCPL-263N[1] HCPL-063N[1] 1,000 50 12.5 [3] HCPL-193X[1] HCPL-56XX[1] HCPL-66XX[1] Notes: 1. Technical data are on separate HP publications. 2. 15 kV/µs with VCM = 1 kV can be achieved using HP application circuit. 3. Enable is available for single channel products only, except for HCPL-193X devices. 1-148 Ordering Information Specify Part Number followed by Option Number (if desired). Example: HCPL-2611#XXX 020 = 5000 V rms/1 minute UL Rating Option* 060 = VDE 0884 VIORM = 630 Vpeak Option** 300 = Gull Wing Surface Mount Option† 500 = Tape and Reel Packaging Option Option data sheets available. Contact Hewlett-Packard sales representative or authorized distributor for information. *For 6N137, HCPL-2601/11/30/31 and HCPL-4661 (8-pin DIP products) only. **For HCPL-2611 only. Combination of Option 020 and Option 060 is not available. †Gull wing surface mount option applies to through hole parts only. Schematic SHIELD 8 6 5 2+ 3 VF USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED BETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE 5). – IF ICC VCC VO GND IO VE IE 7 6N137, HCPL-2601/2611 HCPL-0600/0601/0611 HCNW137, HCNW2601/2611 SHIELD 8 7 + 2 VF1 – IF1 ICC VCC VO1 IO1 1 SHIELD 6 5 – 4 VF2 + IF2 VO2 GND IO2 3 HCPL-2630/2631/4661 HCPL-0630/0631/0661 1-149 1.080 ± 0.320 (0.043 ± 0.013) 2.54 ± 0.25 (0.100 ± 0.010) 0.51 (0.020) MIN. 0.65 (0.025) MAX. 4.70 (0.185) MAX. 2.92 (0.115) MIN. 5° TYP. 0.254 + 0.076 - 0.051 (0.010+ 0.003) - 0.002) 7.62 ± 0.25 (0.300 ± 0.010) 6.35 ± 0.25 (0.250 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) 1.78 (0.070) MAX.1.19 (0.047) MAX. HP XXXXZ YYWW DATE CODE DIMENSIONS IN MILLIMETERS AND (INCHES). 5678 4321 OPTION CODE* UL RECOGNITION UR TYPE NUMBER *MARKING CODE LETTER FOR OPTION NUMBERS "L" = OPTION 020 "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. Package Outline Drawings 8-pin DIP Package** (6N137, HCPL-2601/11/30/31, HCPL-4661) 8-pin DIP Package with Gull Wing Surface Mount Option 300 (6N137, HCPL-2601/11/30/31, HCPL-4661) **JEDEC Registered Data (for 6N137 only). 0.635 ± 0.25 (0.025 ± 0.010) 12° NOM. 9.65 ± 0.25 (0.380 ± 0.010) 0.635 ± 0.130 (0.025 ± 0.005) 7.62 ± 0.25 (0.300 ± 0.010) 5678 4321 9.65 ± 0.25 (0.380 ± 0.010) 6.350 ± 0.25 (0.250 ± 0.010) 1.016 (0.040) 1.194 (0.047) 1.194 (0.047) 1.778 (0.070) 9.398 (0.370) 9.906 (0.390) 4.826 (0.190) TYP. 0.381 (0.015) 0.635 (0.025) PAD LOCATION (FOR REFERENCE ONLY) 1.080 ± 0.320 (0.043 ± 0.013) 4.19 (0.165)MAX. 1.780 (0.070) MAX.1.19 (0.047) MAX. 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). 0.254 + 0.076 - 0.051 (0.010+ 0.003) - 0.002) 1-150 Small-Outline SO-8 Package (HCPL-0600/01/11/30/31/61) 8-Pin Widebody DIP Package (HCNW137, HCNW2601/11) XXX YWW 8 7 6 5 4321 5.842 ± 0.203 (0.236 ± 0.008) 3.937 ± 0.127 (0.155 ± 0.005) 0.381 ± 0.076 (0.016 ± 0.003) 1.270 (0.050)BSG 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.125 ± 0.005) 1.524 (0.060) 45° X 0.432 (0.017) 0.228 ± 0.025 (0.009 ± 0.001) TYPE NUMBER (LAST 3 DIGITS) DATE CODE 0.305 (0.012)MIN. DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). 0.152 ± 0.051 (0.006 ± 0.002) 7° 5678 4321 11.15 ± 0.15 (0.442 ± 0.006) 1.78 ± 0.15 (0.070 ± 0.006) 5.10 (0.201)MAX. 1.55 (0.061) MAX. 2.54 (0.100) TYP. DIMENSIONS IN MILLIMETERS (INCHES). 7° TYP. 0.254 + 0.076 - 0.0051 (0.010+ 0.003) - 0.002) 11.00 (0.433) 9.00 ± 0.15 (0.354 ± 0.006) MAX. 10.16 (0.400) TYP. HP HCNWXXXX YYWW DATE CODE TYPE NUMBER 0.51 (0.021) MIN. 0.40 (0.016) 0.56 (0.022) 3.10 (0.122) 3.90 (0.154) 1-151 8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW137, HCNW2601/11) Note: Use of nonchlorine activated fluxes is highly recommended. Solder Reflow Temperature Profile (HCPL-06XX and Gull Wing Surface Mount Option 300 Parts) 240 ∆T = 115°C, 0.3°C/SEC 0 ∆T = 100°C, 1.5°C/SEC ∆T = 145°C, 1°C/SEC TIME – MINUTES TE M PE R A TU RE – °C 220 200 180 160 140 120 100 80 60 40 20 0 260 1 2 3 4 5 6 7 8 9 10 11 12 1.00 ± 0.15 (0.039 ± 0.006) 7° NOM. 12.30 ± 0.30 (0.484 ± 0.012) 0.75 ± 0.25 (0.030 ± 0.010) 11.00 (0.433) 5678 4321 11.15 ± 0.15 (0.442 ± 0.006) 9.00 ± 0.15 (0.354 ± 0.006) 1.3 (0.051) 12.30 ± 0.30 (0.484 ± 0.012) 6.15 (0.242) TYP. 0.9 (0.035) PAD LOCATION (FOR REFERENCE ONLY) 1.78 ± 0.15 (0.070 ± 0.006) 4.00 (0.158)MAX. 1.55 (0.061) MAX. 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). 0.254 + 0.076 - 0.0051 (0.010+ 0.003) - 0.002) MAX. 1-152 Regulatory Information The 6N137, HCPL-26XX/06XX/ 46XX, and HCNW137/26XX have been approved by the following organizations: UL Recognized under UL 1577, Component Recognition Program, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. VDE Approved according to VDE 0884/06.92. (HCPL-2611 Option 060 and HCNW137/26X1 only) BSI Certification according to BS415:1994 (BS EN60065:1994), BS7002:1992 (BS EN60950:1992) and EN41003:1993 for Class II applications. (HCNW137/26X1 only) Insulation and Safety Related Specifications 8-pin DIP Widebody (300 Mil) SO-8 (400 Mil) Parameter Symbol Value Value Value Units Conditions Minimum External L(101) 7.1 4.9 9.6 mm Measured from input terminals Air Gap (External to output terminals, shortest Clearance) distance through air. Minimum External L(102) 7.4 4.8 10.0 mm Measured from input terminals Tracking (External to output terminals, shortest Creepage) distance path along body. Minimum Internal 0.08 0.08 1.0 mm Through insulation distance, Plastic Gap conductor to conductor, usually (Internal Clearance) the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Minimum Internal NA NA 4.0 mm Measured from input terminals Tracking (Internal to output terminals, along Creepage) internal cavity. Tracking Resistance CTI 200 200 200 Volts DIN IEC 112/VDE 0303 Part 1 (Comparative Tracking Index) Isolation Group IIIa IIIa IIIa Material Group (DIN VDE 0110, 1/89, Table 1) Option 300 - surface mount classification is Class A in accordance with CECC 00802. 1-153 VDE 0884 Insulation Related Characteristics (HCPL-2611 Option 060 Only) Description Symbol Characteristic Units Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 300 V rms I-IV for rated mains voltage ≤ 450 V rms I-III Climatic Classification 55/85/21 Pollution Degree (DIN VDE 0110/1.89) 2 Maximum Working Insulation Voltage VIORM 630 V peak Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 1181 V peak Partial Discharge < 5 pC Input to Output Test Voltage, Method a* VIORM x 1.5 = VPR, Type and sample test, VPR 945 V peak tm = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) VIOTM 6000 V peak Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 16, Thermal Derating curve.) Case Temperature TS 175 °C Input Current IS,INPUT 230 mA Output Power PS,OUTPUT 600 mW Insulation Resistance at TS, VIO = 500 V RS ≥ 109 Ω *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section (VDE 0884), for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. VDE 0884 Insulation Related Characteristics (HCNW137/2601/2611 Only) Description Symbol Characteristic Units Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 600 V rms I-IV for rated mains voltage ≤ 1000 V rms I-III Climatic Classification (DIN IEC 68 part 1) 55/100/21 Pollution Degree (DIN VDE 0110/1.89) 2 Maximum Working Insulation Voltage VIORM 1414 V peak Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 2651 V peak Partial Discharge < 5 pC Input to Output Test Voltage, Method a* VIORM x 1.5 = VPR, Type and sample test, VPR 2121 V peak tm = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) VIOTM 8000 V peak Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 16, Thermal Derating curve.) Case Temperature TS 150 °C Input Current IS,INPUT 400 mA Output Power PS,OUTPUT 700 mW Insulation Resistance at TS, VIO = 500 V RS ≥ 109 Ω *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section (VDE 0884), for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. 1-154 Absolute Maximum Ratings* (No Derating Required up to 85°C) Parameter Symbol Package** Min. Max. Units Note Storage Temperature TS -55 125 °C Operating Temperature† TA -40 85 °C Average Forward Input Current IF Single 8-Pin DIP 20 mA 2 Single SO-8 Widebody Dual 8-Pin DIP 15 1, 3 Dual SO-8 Reverse Input Voltage VR 8-Pin DIP, SO-8 5 V 1 Widebody 3 Input Power Dissipation PI Widebody 40 mW Supply Voltage VCC 7 V (1 Minute Maximum) Enable Input Voltage (Not to VE Single 8-Pin DIP VCC + 0.5 V Exceed VCC by more than Single SO-8 500 mV) Widebody Enable Input Current IE 5 mA Output Collector Current IO 50 mA 1 Output Collector Voltage VO 7 V 1 (Selection for Higher Output Voltages up to 20 V is Available.) Output Collector Power PO Single 8-Pin DIP 85 mW Dissipation Single SO-8 Widebody Dual 8-Pin DIP 60 1, 4 Dual SO-8 Lead Solder Temperature TLS 8-Pin DIP 260°C for 10 sec., (Through Hole Parts Only) 1.6 mm below seating plane Widebody 260°C for 10 sec., up to seating plane Solder Reflow Temperature SO-8 and See Package Outline Profile (Surface Mount Parts Only) Option 300 Drawings section *JEDEC Registered Data (for 6N137 only). **Ratings apply to all devices except otherwise noted in the Package column. †0°C to 70°C on JEDEC Registration. Recommended Operating Conditions Parameter Symbol Min. Max. Units Input Current, Low Level IFL* 0 250 µA Input Current, High Level[1] IFH** 5 15 mA Power Supply Voltage VCC 4.5 5.5 V Low Level Enable Voltage† VEL 0 0.8 V High Level Enable Voltage† VEH 2.0 VCC V Operating Temperature TA -40 85 °C Fan Out (at RL = 1 kΩ)[1] N 5 TTL Loads Output Pull-up Resistor RL 330 4 k Ω *The off condition can also be guaranteed by ensuring that VFL ≤ 0.8 volts. **The initial switching threshold is 5 mA or less. It is recommended that 6.3 mA to 10 mA be used for best performance and to permit at least a 20% LED degradation guardband. †For single channel products only. 1-155 Electrical Specifications Over recommended temperature (TA = -40°C to +85°C) unless otherwise specified. All Typicals at VCC = 5 V, TA = 25°C. All enable test conditions apply to single channel products only. See note 5. Parameter Sym. Package Min. Typ. Max. Units Test Conditions Fig. Note High Level Output IOH* All 5.5 100 µA VCC = 5.5 V, VE = 2.0 V, 1 1, 6, Current VO = 5.5 V, IF = 250 µA 19 Input Threshold ITH Single Channel 2.0 5.0 mA VCC = 5.5 V, VE = 2.0 V, 2, 3 19 Current Widebody VO = 0.6 V, Dual Channel 2.5 IOL (Sinking) = 13 mA Low Level Output VOL* 8-Pin DIP 0.35 0.6 V VCC = 5.5 V, VE = 2.0 V, 2, 3, 1, 19 Voltage SO-8 IF = 5 mA, 4, 5 Widebody 0.4 IOL (Sinking) = 13 mA High Level Supply ICCH Single Channel 7.0 10.0* mA VE = 0.5 V VCC = 5.5 V 7 Current 6.5 VE = VCC IF = 0 mA Dual Channel 10 15 Both Channels Low Level Supply ICCL Single Channel 9.0 13.0* mA VE = 0.5 V VCC = 5.5 V 8 Current 8.5 VE = VCC IF = 10 mA Dual Channel 13 21 Both Channels High Level Enable IEH Single Channel -0.7 -1.6 mA VCC = 5.5 V, VE = 2.0 V Current Low Level Enable IEL* -0.9 -1.6 mA VCC = 5.5 V, VE = 0.5 V 9 Current High Level Enable VEH 2.0 V 19 Voltage Low Level Enable VEL 0.8 V Voltage Input Forward VF 8-Pin DIP 1.4 1.5 1.75* V TA = 25°C IF = 10 mA 6, 7 1 Voltage SO-8 1.3 1.80 Widebody 1.25 1.64 1.85 TA = 25°C 1.2 2.05 Input Reverse BVR* 8-Pin DIP 5 V IR = 10 µA 1 Breakdown SO-8 Voltage Widebody 3 IR = 100 µA, TA = 25°C Input Diode ∆VF/ 8-Pin DIP -1.6 mV/°C IF = 10 mA 7 1 Temperature ∆TA SO-8 Coefficient Widebody -1.9 Input Capacitance CIN 8-Pin DIP 60 pF f = 1 MHz, VF = 0 V 1 SO-8 Widebody 70 *JEDEC registered data for the 6N137. The JEDEC Registration specifies 0°C to +70°C. HP specifies -40°C to +85°C. 1-156 Switching Specifications (AC) Over Recommended Temperature (TA = -40°C to +85°C), VCC = 5 V, IF = 7.5 mA unless otherwise specified. All Typicals at TA = 25°C, VCC = 5 V. Parameter Sym. Package** Min. Typ. Max. Units Test Conditions Fig. Note Propagation Delay tPLH 20 48 75* ns TA = 25°C RL = 350 Ω 8, 9, 1, 10, Time to High 100 CL = 15 pF 10 19 Output Level Propagation Delay tPHL 25 50 75* ns TA = 25°C 1, 11, Time to Low 100 19 Output Level Pulse Width |tPHL - tPLH| 8-Pin DIP 3.5 35 ns 8, 9, 13, 19 Distortion SO-8 10, Widebody 40 11 Propagation Delay tPSK 40 ns 12, 13, Skew 19 Output Rise tr 24 ns 12 1, 19 Time (10-90%) Output Fall tf 10 ns 12 1, 19 Time (90-10%) Propagation Delay tELH Single Channel 30 ns RL = 350 Ω, 13, 14 Time of Enable CL = 15 pF, 14 from VEH to VEL VEL = 0 V, VEH = 3 V Propagation Delay tEHL Single Channel 20 ns 15 Time of Enable from VEL to VEH *JEDEC registered data for the 6N137. **Ratings apply to all devices except otherwise noted in the Package column. Parameter Sym. Device Min. Typ. Units Test Conditions Fig. Note Logic High |CMH| 6N137 10,000 V/µs |VCM| = 10 V VCC = 5 V, IF = 0 mA, 15 1, 16, Common HCPL-2630 VO(MIN) = 2 V, 18, 19 Mode HCPL-0600/0630 RL = 350 Ω, TA = 25°C Transient HCNW137 Immunity HCPL-2601/2631 5,000 10,000 |VCM| = 50 V HCPL-0601/0631 HCNW2601 HCPL-2611/4661 10,000 15,000 |VCM| = 1 kV HCPL-0611/0661 HCNW2611 Logic Low |CML| 6N137 10,000 V/µs |VCM| = 10 V VCC = 5 V, IF = 7.5 mA, 15 1, 17, Common HCPL-2630 VO(MAX) = 0.8 V, 18, 19 Mode HCPL-0600/0630 RL = 350 Ω, TA = 25°C Transient HCNW137 Immunity HCPL-2601/2631 5,000 10,000 |VCM| = 50 V HCPL-0601/0631 HCNW2601 HCPL-2611/4661 10,000 15,000 |VCM| = 1 kV HCPL-0611/0661 HCNW2611 1-157 Package Characteristics All Typicals at TA = 25°C. Parameter Sym. Package Min. Typ. Max. Units Test Conditions Fig. Note Input-Output II-O* Single 8-Pin DIP 1 µA 45% RH, t = 5 s, 20, 21 Insulation Single SO-8 VI-O = 3 kV dc, TA = 25°C Input-Output VISO 8-Pin DIP, SO-8 2500 V rms RH ≤ 50%, t = 1 min, 20, 21 Momentary With- Widebody 5000 TA = 25°C 20, 22 stand Voltage** OPT 020† 5000 Input-Output RI-O 8-Pin DIP, SO-8 1012 Ω VI-O = 500 V dc 1, 20, Resistance Widebody 1012 1013 TA = 25°C 23 1011 TA = 100°C Input-Output CI-O 8-Pin DIP, SO-8 0.6 pF f = 1 MHz, TA = 25°C 1, 20, Capacitance Widebody 0.5 0.6 23 Input-Input II-I Dual Channel 0.005 µA RH ≤ 45%, t = 5 s, 24 Insulation VI-I = 500 V Leakage Current Resistance RI-I Dual Channel 1011 Ω 24 (Input-Input) Capacitance CI-I Dual 8-Pin DIP 0.03 pF f = 1 MHz 24 (Input-Input) Dual SO-8 0.25 *JEDEC registered data for the 6N137. The JEDEC Registration specifies 0°C to 70°C. HP specifies -40°C to 85°C. **The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable), your equipment level safety specification or HP Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage.” †For 6N137, HCPL-2601/2611/2630/2631/4661 only. Notes: 1. Each channel. 2. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not exceed 20 mA. 3. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not exceed 15 mA. 4. Derate lin