the gsm sagem ot160 gsm900dcs1800 network test the mobile operating manual (manual)
The GSM SAGEM OT160 GSM900DCS1800 network test the mobile
operating manual (manual)
SAGEM OT160 is a daily essential network test tool for network operators and network maintainers. SAGEM OT160 is used for GSM900 and DCS1800 network tests.
Here is the SAGEM OT160 network test action step:
Action button: enter the main menu by the specific key, # or #, and it represents the 7 options for OT160:
MINFO 1 MS (mobile platform information)
NETWORK (NETWORK data test)
3 SIM INFO (SIM information)
FORCING FUNCTION (forced FUNCTION)
5 BCCH SCANNING (BCCH scan)
6 QOS INFO
SERIAL LINK SETUP (SERIAL port Settings)
To exit the main menu, press the 'C' key
After entering the main menu, press the button or the button to select a feature
Note: in the test menu, ACTIVE indicates that the function is activated, non-active table
A function is not activated. At the same time, OT160 performs the GSM proposal.
GSM900 channel number: 1 to 124 (from 96-124)
DCS1800 channel number: from 512 to 885 (unicom 662-736)
"-" means no relevant information
The various test menus will be illustrated below:
Select menu 1, 'OK', or press '1' directly under the main menu under the 'click' button or 'click' button.Enter the menu 1 MS INFO
Menu 1: MS INFO
MINFO 1 MS INFO IMEI
NETWORK TMSI/Ciphering
3 SIM INFO
4 FORCING FUNCTION
5 BCCH SCANNING
6 the QOS INFO
7 SERIAL LINK SETUP
1. The IMEI
Display IMEI (international mobile device id), software version
2. TMSI/Ciphering
? TMSI temporary mobile station identification number
? Ciphering GSM encryption state
? Algo GSM encryption algorithm
To return to the main menu, press the 'C' key
Under the main menu, select menu 2, "OK," or press the digital key "2"
2 the NETWORK into the menu
Menu 2: NETWORK (NETWORK data)
This feature is used to display the main parameters of the free and voice modes received from the service community and adjacent communities. You can type the remote phone number and the "call button" on the screen for a dial-up call and then automatically return to the tracking screen. You can also use the "call button" to call the last remote phone number.
In the free mode: the service area network data
2 adjacent network dataIn the telephone mode: the service area network data
2 adjacent network data
In the mode of the call, cooperate with menu 4 and can also carry out the tracking test. Call any phone number that displays the network data of the service area and the adjacent neighborhood.
Both service area and adjacent six village, every village has two panel data, so a total of 14 optional screen, using bring key or ? button on a screen or on the next screen.
On these screens, press the 'OK' button to display the content of the additional screen.
This data value is used when the receiving conditional difference does not show the data about the network.
In the absence of a call, press '2' to enter the NETWORK function under the main menu:
In the free mode: the service area network data
Screen display:
CH...
TS times BA times x
BSIC x times x: times x times x times x
So we have RX times C1 times C2 times C2 times 2
RM times CI times x times x
LAI * * * * * * *
These two screens show the following data for the service community in the free way:
CH:
Radio frequency channel number (BCCH in idle mode)
TS: 0 to 7
Current footprint (BCCH = 0 in idle mode)
BA: nm xy
The number of cells in the BA table
1 to 32 nm
Configure CCCH values for BCCH and PCH
X 2 to 9
Y, 0, 1, 2, 4, or 6
BS_PA_MFRMS_2 current value
Control channel current values? The BSIC: ab
Service area base station identification number
A 0 to 7
0 to 7 b
Operating company code
Residential area color code
TX:
Mobile power
CD/md:
CD
md
Descending confidence indicator values
Descending confidence indicator values
The maximum value of the downward letter
RX: - 110 DBM to 11
The service community BCCH receives the level value
C1: -92 to + 127
Service community standard C1
C2:92 to + 127
Service area standard C2 value
RM: - 110-46 DBM
Minimum receive threshold level
CI: abcde
Community identification number, 4 16-bit system
LAI: ABC DE fghij
Regional identification number
ABC
DE
fghij
The country code, using the three-digit number (China is 460)
Running the company code, using a two-digit representation (link is 01)
Area code, expressed in five digits (location LAC)
Menu 4: FORCING FUNCTION (forced FUNCTION)
1 Set BCCH
MINFO 1 MS INFO 2 Set HO
NETWORK 3 Cell Bar Access
3 SIM INFO 4 Negative C1
4 the FUNCTION FUNCTION 5 Set Power Class
5 BCCH SCANNING 6 RF Measurement6 QOS INFO 7 Set Full Rate
SERIAL LINK SETUP 8 Set Band
The Set of 9 Cell Reselection
10 the Summary
The Set BCCH
For locking BCCH,
Note: RF Measurement, RF Scaning, BCCH Scaning functions cannot be used at the same time
The Set HO
This feature is used to activate or disable the switch in a community.
There are two options for the more active transformation of the region:
The conversion of a single, or cyclical, region
The Cell Bar Access
Non active
inverse
The active
This feature defines the interpretation of Cell_bar_access_s and provides three modes for selecting:
The mobile complies with GSM recommendation
The mobile only camps on cells.
The mobile camps on barred and non-barred cell
? Negative C1
Set the Power Class
The RF Measurement
The Set Full Rate
The Set Band
Set the Cell Reselection
The Summary
This feature allows the OT160 to stay in the active state when C1 is less than 0
Define the power level of the OT160 in the 900MHz band,It can be defined as 2W (CLASS 4) or 0.8 W (CLASS 5). You can define 1W (CLASS 1) or 0.25 W (CLASS 2) in the 1800MHz band.
Regardless of channel type, can you specify rf channel and test field strength level
To lock the OT160 in full rate mode.
To lock OT160 in 900Hz, 1800Hz, or 900Hz / 1800Hz band. After setting this lock, OT160 is closed. When the OT160 is reopened, the set takes effect.
This feature is used to activate and disable the community reelection.
This function is used to display the mandatory functionality
of all options
本文档为【the gsm sagem ot160 gsm900dcs1800 network test the mobile operating manual (manual)】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑,
图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。