Readme(AP5010_4000)（自述（ap5010_4000））

Readme(AP5010_4000)（自述（ap5010_4000）） Readme(AP5010_4000)(自述(ap5010_4000)) ================================= Fuji Xerox PCL 6 print driver license agreement ================================= 1. ownership: the name, ownership and intellectual property rights of the software belong to Fuji Xerox and its third parties Supplier ownership. Except as expressly provided in this agreement, you do not have any other rights to this software. 2. license: under this agreement, you are granted a non exclusive license, that is, in your country, will be compatible with this software Fuji Xerox products are in use simultaneously. You may not (1) pass through any tangible medium, such as floppy disks, tapes, or To transfer, transfer, lease, lease, lease, transfer or transfer the software to any third party, (2) sell the software publicly through the network or telephone line; or (3) all or part of the software Change, modify, decode, decompose, reverse engineer, or produce derivative works. Be sure to make sure that all the instructions on the use or limitations of this software are within this web site Abide by. 3. time limit: this Agreement comes into effect upon the installation of this software until you destroy this software and terminate the agreement. This agreement will also be terminated if you fail to comply with any of the terms of this agreement. After the termination of the agreement, you should immediately Destroy this software. 4. limited warranty: this software is strictly "provided by the status quo" without any warranty, whether it be express or Implied warranties include, but are not limited to, the merchantability of the software and whether it can be used for a particular purpose Any guarantee. You should be responsible for the selection, maintenance and matching of other hardware and software, and the use of this software. In any case, Fuji Xerox Co, Fuji Xerox channels, business partners, authorized dealers and their Any third party supplier shall not be liable for any loss or damage caused by the failure to use the software, Including incidental or consequential loss or damage, or liability for any modification of the software. 5. export control: you must not violate the relevant restrictions, laws or regulations of your country or other countries concerned Or indirectly export part or all of this software, you need to obtain the necessary approval before you export the software. --------------------------------------------------------------------- --- FX, ApeosPort-II, 5010/4000, PCL, 6 --- --- DocuCentre-II 5010/4000 PCL 6 --- --- --- Windows, Server (R), 2003, x64, Edition --- --- --- Windows, Server (R), 2008, x64, Edition --- --- --- Windows Vista (R) x64 Edition print driver - --- --- 2.6.2 (1/1) - - --- --- June 2008 --- --- - - readme - - --------------------------------------------------------------------- File contents include 1. requirements 2. file configuration 3. installation 3.1., Windows (R), XP, x64, Edition, Windows, Server (R) 2003, x64, Edition install Install under 3.2. Windows Vista (R) x64 Edition 3.3., Windows (R), XP, x64, Edition, Windows, Server (R) 2003, x64, Edition uninstall 3.4., Windows, Vista (R), x64, Edition, uninstall Four General description 5. restrictions 6. software upgrade 1. requirements ======= 1. note that this printer driver will be based on the 64 bit x64 microprocessor (AMD64 or Intel EM64T), equipped with an upwardly compatible processor, and running Windows (R), XP, x64, Edition, or Windows Server (R) 2003 x64 Edition Or Windows Server (R) 2008 x64 Edition or Windows Vista (R) x64 Edition Run on the Chinese version of the computer. 2. file configuration =========== Fx6ngie.inf Fx6ngeiu.dll Fx6ngeim.dll Fx6ngjdm.dll Fx6ngeir.xrs Fx6ngkdm.dll Fxzddmif.dll Fxzdhb32.dll Fxzdmifk.dll Fxzpmc4.dll Fxzadcmn.dll Fxzarl32.dll Fxzypxa4.dll Fxlzjnie.dll Fxlznie1.dll Fxzvup.exe Fxzkvup.dll Fxzypf01.exe Fxzypf01.dll Fx6nge.cfg Fx6nge.tbl Fx6nge.hlp Fx6nge.cnt Fx6nge.xrs Fx6nge.cdd Fx6nge.ddd Fx6nhe.ddd Fx6nie.ddd Fx6nje.ddd Fx6nke.ddd 3. installation ======= Please install the PCL6 printer driver as follows. Here, we will install and uninstall the ApeosPort-II 5010 PCL 6 printer driver as an example Explain. 3.1., Windows (R), XP, x64, Edition, Windows, Server (R) 2003, x64, Edition install ==================================================================== (1) click the start button. Point the mouse to settings, and click printers and faxes". (2) double click the Add Printer icon in the printer and fax dialog box, then follow the dialog Instructions。 (3) if the printer is connected directly to your computer or using the LPR protocol to connect to the network, select "connect to" Local printer of this computer, click next to >], and follow the steps of (5) instructions. Otherwise, select a network printer or a printer that is connected to another computer". (4) connect to the required printer in the following manner: * find a printer in the directory * connect to this printer (or browse the printer, select this option, and click next), Or click "connect to the printer on the Internet, home or office network" to enter in the following format Name。 \\printserver_name\share_name After that, follow the instructions of step (10). If you are not familiar with the network, consult your network administrator. (5) select the port you want to use your printer, click next >], go to step (7). If the printer uses the LPR protocol to connect to the network, select "create new port" "Standard TCP/IP Port" and click next >]. "Welcome to using the standard TCP/IP printer port Wizard" dialog box will show. Click next to >]. (6) enter the printer name or IP address in the printer name or IP address edit box. If you don't know the printer name or IP address, consult your network administrator. "Completing the standard TCP/IP printer port Wizard dialog box" is displayed. Click [finish]. (7) on the Add Printer Wizard screen, click [install from disk]. "Install from disk" screen will show. Specifies the folder that contains the drive file. Then choose The INF file in the folder, and click [OK]. (8) "ApeosPort-II 5010, PCL 6" will appear in the dialog box. Please select a printer and Click next to >]. If the printer you selected is already installed, It displays information about whether to replace the existing driver. When you install a new version of the printer driver, select "replace the existing driver"". drive Older versions of programs, such as those used in applications, will not be deleted. In this case, close the application. (9) the dialog box that specifies the printer name will display. To change the printer name, enter any name in the printer name box. If installed, other The printer will have information to see if the printer is set as the default printer. Click [yes]. (10) please specify whether to share this printer with other network users. (11) specifies whether the dialog box that prints the test page after installation will display. If you choose "yes", please put the paper into the printer and click next >]. If you don't print a test page, please select "no" and click next >]. (12) the dialog box that confirms the settings will display. After you confirm the setting, click finish. (13) the information that does not pass the Windows logo test will show, but this does not lead to functional problems. Click [continue]. (14) the necessary files will be copied, and the new printer icon will be created. If you have printed the test page, the printer test results confirmation information will be displayed. Installation complete. Install under 3.2. Windows Vista (R) x64 Edition ======================================== (1) click start, select [control panel], then click [hardware and sound], and click [printer]. (2) select [Add Printer] from the menu bar. (3) if the printer is connected directly to your computer or using the LPR protocol to connect to the network, select Add a local printer, click next >], and follow the steps of (5) instructions. Otherwise, select "add network, wireless or Bluetooth printer"". (4) select [the printer I need is not on the list]. Please connect to the required printer by: * search in Active Directory Select [printer] * browse, then click next >] to lock on the network printer, Or select [share printer by name] enter the name in the following format. \\printserver_name\share_name After that, follow the instructions of step (11). If you are not familiar with the network, consult your network administrator. (5) select the printer device directly connected to the printer port, click next >], go to step (7). If the printer uses the LPR protocol to connect to the network, select "create new port" "Standard TCP/IP Port", and click [Standard TCP/IP port]. (6) enter the hostname or IP address in the host name or IP address edit box. If you don't know Host name or IP address, please consult the network administrator. (7) in the Add Printer, click [install from disk], and then specify the include driver Folder for program files. Then select the INF file in the folder, and click [OK]. (8) "FX ApeosPort-II 5010, PCL 6" will appear in the dialog box. Please select the printer And click [next step]. If the selected printer has been installed, you will display information to ask if you want to replace the current driver. When you install a new version of the printer driver, select "replace the current driver"". Older versions of drivers, such as those used in applications, will not be deleted. In this case, close the application. (9) the dialog box that type the printer name will display. To change the printer name, enter any name in the printer name box. If installed Other printers, The message will be asked whether to set the printer as the default printer. Confirm that set to default printer is selected. (10) the user account control dialog box will be displayed and asked if you want to continue [printer driver software installation]. Click [continue]. When using a user account other than an administrator When installing, you need the administrator's password. (11) start of installation. A message "Windows cannot verify this driver software publisher" will be displayed, But this does not cause functional problems. Click "always install this driver software" to continue Installation. (12) please specify whether to share this printer with other network users. (13) specifies whether the dialog box that prints the test page after installation will display. Click the print test page button To print the test page. Otherwise, if you don't want to print the test page, click finish. 3.3., Windows (R), XP, x64, Edition, Windows, Server (R) 2003, x64, Edition uninstall ==================================================================== (1) remove your installed printer icon from the printer dialog box of the control panel. 3.4., Windows, Vista (R), x64, Edition, uninstall ======================================== (1) enter the "control panel", click [hardware and sound], open the printer dialog box, and then Right click the printer icon to uninstall. Enter "run with administrator account" and select [delete]. 4. general description =========== (1) please close all running applications before you install the printer driver. (2) restart the computer after you install an updated version of the printer driver. (3) if you have deleted the older version of the printer driver, restart it before you install the new version Computer。 (4) some applications provide printing functions such as typing and pagination. If no special instructions, please always follow Select these print functions in the application. Please select some advanced in the printer driver dialog Options such as double print, sample printing, or functions not provided in the application. (5) before you make any changes to the default settings for the printer driver by pressing the control panel, print off Print dialog in the machine driver dialog box and / or application. (6) if the electronic paging output and paging function are not running properly, you can try not to select the application Tab select the tab check box in the printer driver. (7) the current user may not have the right to do so if the fax book has not been initialized or is not created by the current user Access. Once the user has such improper access, the driver displays an error message that prompts the default The fax book cannot be locked, or the specified fax book cannot be identified. However, if the user wishes his / her fax directory could be accessed by another user, the user would specify Allow groups and users and give them at least the right to change access to fax book data Document. (8) fax operations must be sent to the receiver specified in the F- code, password, or secret sending attribute. Otherwise, the printer will ignore the F- code, password, or confidential sending attribute, and send the fax job For multiple receivers. The job that is sent will be printed directly at all designated destinations. (9) if the shared printer client uses the operating system, it is not the operating system specified by this driver, You must install alternate drivers for each operating system. The version of the alternate driver should be consistent with the version of this driver. Otherwise, the standby drive There may be an error in the installation of the order. Also, the following operating system cannot be used by clients sharing printers. - any version below Windows XP SP2 - any version below Windows Server 2003 SP1 - Windows 2000 If you use any of the above operating systems on the client side and install a shared printer, print The properties of the machine folder may not be opened. (10) for the installation on the Windows Vista (R) over the network, if you right-click [printer] Folder, enter from menu, run with administrator account, and select [Add Printer], The printer icon may not be generated. (11) Windows. Jiaopiao Jun series version of alum coupons to skid pan Fu Ji Qiao g Elao indigo roll might put just a calendar Jiaopiao. Alum wolf series Elao indigo indigo domain Jun Fu Ji Qin g Juqin roll please. 5. restrictions =========== (1) when the printed form or chart is different from what you see on the screen, change the following settings Light problem. * change the "image quality" settings in the "image options" tab. * change the "Brightness" and "contrast" settings in the "image options" tab. * set "fast image processing" to "no" in the "Settings" tab". * use the thin line drawing according to resolution in the Settings tab. Set it as "yes"". * changes in "resolution" in the "other settings (graphics settings)" tab of the "specific settings" tab" Set up。 * Change "half tone" in the "specific settings" tab of the other settings (graphics settings) tab Print settings. (2) change the "image quality" setting in the "image options" tab, which may change the print layout. (3) according to the application, if the image quality is "high resolution" or "driver resolution" For "1200dpi", the printing data will be large and the printing may not be normal. When this happens, please specify the following settings: * specify the image quality of the "image options" label as "standard" or "specify"" Other settings (graphics settings) for the tag are specified as "600dpi" and "300dpi"" Or "200dpi."". (4) for some applications, if the pasted image is printed at a high resolution, the print data will be extended And may cause printing speed to be slowed down significantly. The size of the output print data may change by setting the "specific" label Change in the following settings in other settings (graphics settings). * specifies the image compression in the other settings (graphics settings) of the specific settings tab" For "standard" or "photo", or specify "resolution" for "300dpi" or "200dpi"". (5) when printing from the English version of QuarkXpress 6.1, if the "image quality" is set to " "High resolution" and the driver's resolution is "1200dpi", then the document may be Blank page print. This problem can be avoided by changing the resolution of the driver to "automatic". (6) when printing from the Visio2003 application, set the "image quality" from before printing If the standard is changed to "high resolution", the printed data may be scaled down and printed in the upper left corner. Before launching the application, "image quality" is printed in the "image options" tab of the printer driver" Set to "high resolution" can solve this problem. (7) make sure the settings are printed in the application when the specified paper source is "automatic" for print jobs The paper size is the size of the driver supported paper, so that automatic paper feed function is available. (8) when using the "image overlay" function, Use the size of the paper and the resolution of the text you want to print Format data the same as the image settings. If formatted data and formatted data are synthesized of pages Set differently, you will not get the desired print effect. (9) when formatting is used, some applications print the background white, with The overprinting format may be hidden. Such applications include Internet, Explorer, and WordPad. (10) print with Adobe PageMaker, when this printer is specified as "combination to printer", It might change the layout. This problem can be avoided in advance by performing the following steps: <1> do not set "combine" to printer". <2> changes margin settings on the margin tab. <3> specifies "print to edge" on the print area label". Note: in the <2> and <3> steps, click the [offset / print position] from the Layout tab Button to open the margins and print area labels. (11) when printing a document that exceeds the printer driver print area, if you select multiple sheets and Print area [standard], the print contents overlap. When this happens, select "layout"" Print to edge in the print area dialog box of the "image offset / print position" on the label". (12) you must register the mailbox on the printer in order to use the save to mailbox function. About how to board Note box, please refer to the printer manual. On DocuCentre-II 5010/4000, only scanner components can be installed [save to mailbox] function. (13) when you cancel an ongoing fax job from the driver, the application displays a warning Dialog box。 Although the printer is not wrong, it may contain printer error messages. Under such circumstances, Ignore the warning message and proceed with the operation. (14) depending on the application that the user uses, such as the number of copies specified under output double-sided printing, Automatically inserts blank pages for page adjustments. In this case, the application will insert a blank page. Performance can be improved by changing the following settings. In the "specific set" label "skip blank page check". (15) even if you choose to skip a blank page, the blank page may be printed out in the following cases: * the page contains a newline. * pages contain spaces. * pages contain line feeds and spaces. * send white background drawing instructions from the application. (16) for Microsoft (R) Word, even if the specified skip blank page is included in the file When you have a blank page, you may also output blank pages. (17) for the use of Microsoft Windows Server 2000 or Microsoft Windows 2003 Server cluster environment customers <1> uses the following operating system (32 bit version) as the client: Microsoft (R) Windows (R) 2000 Microsoft (R) Windows (R) XP Microsoft (R) Windows Server (R) 2003 <2> specifies custom paper sizes in a cluster environment to refer to all physical nodes in a cluster environment Fixed universal settings. <3> press [get information] button, [search printer] dialog box appears, enter the dozen Printer's network address. <4> removes drivers in a cluster environment (A) Microsoft Windows Server 2000 After deleting the drivers on the virtual server, remove all drivers on the inactive node. (B) Microsoft Windows 2003 Server After deleting the drivers on the virtual server, remove all drivers on the inactive node. * removes drivers from inactive nodes (B-1) change the inactive node to the actual node. (b-2) install printers on the virtual server. (B-3) remove the driver from the virtual server. <5> delete driver After removing the printer icon, remove the driver from [server properties]. And then, again Start the computer. (18) [cancel the button] in the user specific settings dialog box For some applications, if prompted on the [specific user configuration] dialog box [prompt user settings] When setting to print, cancel the [enter user specific settings] dialog box, and may display a warning message Dialog box。 This warning information dialog box may indicate a printer error, but, in fact, the printer No problem。 In this case, ignore the warning message and proceed with the operation. (19) functional limitations of EMF spooling The following functions may not function properly when the [EMF spooling of a setting label is set to 'available'. To use these functions, set [EMF spooling to "unavailable"". * [[] [] confidential print sample print print, save to delay the mailbox * [enable account management] [specific user settings] * [email job notification] * [header / footer options] * [creation / registration format] [divider / page] [delimited pages] * [image adjustment mode] [ICM adjustment] * [use of extended functionality in applications] * [enable user defined margins] * all functions of the direct fax driver For details about [header / footer options] restrictions, please refer to the function of the header / footer option". A document with a mixed structure is set as "unavailable" when the "[EMF" of the setting label is set "unavailable" Problems may occur when printing, such as output image distortion and / or failure. In the Windows Vista environment, the document can be output normally. In Windows, XP, and Windows Server 2003 environments, documents can also be applied through SP2 Normal output. (20) to change the settings for custom paper sizes, you need to have administrator privileges. On Windows Vista, Select the printer from the printer folder, right click to enter [run with administrator account] and select [properties]. After you click [continue] in user account control, you can change settings from properties. (21) the data in the cross subnet broadcast cannot be retrieved under the default setting of the Windows Vista firewall. Do not use broadcast and direct address for searchable cross subnet data. (22) the following is about faxing in the Internet Explorer protection mode of Windows Vista Print feature limit: After performing fax printing, you may immediately display warning messages. - the saved location of the fax book book is not a public folder that is commonly used for saving, but can be used as File creation folder (such as personal folder). Therefore, the contents of the fax book are different from What is registered with other applications?. - unable to run import of fax phone book to list function. (23) the file creation is restricted from the Internet Explorer of Windows Vista. You will not be able to specify The format data file in the folder is saved as the default value in the create / register format. Before you create / register a format data file, change the folder to available for creating files Folder (such as document folder). (24) watermark function 在Windows XP SP2、Windows Server 2003 SP2和Windows Vista环 境下， 当[ ] [ ]具体设定标签的EMF假脱机设为”不可用”时，通过32位 应用程序 软件不可使用[水印]。要使用此功能，请将[势]设为假脱机”可用”。 (25)页眉/页脚选项功能 当[ ] [ ]具体设定标签的EMF假脱机设为”可用”时，[页眉/页脚选项] 可供使用。要使用此功能，请将[势]设为假脱机”不可用”。 但是，在Windows XP SP2、Windows Server 2003 SP2和Windows Vista 环境下，即使[势]设为假脱机”不可用”时，通过32位应用程序 软件不可使用此功能。 (26)橇赴磐辑滚俊辑Windows Vista(R)捞惑狼滚傈栏肺橇赴磐 靛扼捞滚甫盔拜栏肺汲摹且版快沥惑利栏肺汲摹登瘤臼阑荐档 乐嚼聪促。Windows(R)XP俊辑盔拜栏肺汲摹且巴阑鼻厘钦聪促。 6。软件升级 =========== 最新软件可通过本公司网站获取。 通讯费用由客户自行承担。 本软件的部分 内容 财务内部控制制度的内容财务内部控制制度的内容人员招聘与配置的内容项目成本控制的内容消防安全演练内容 基于独立JPEG群组的工作。 微软为微软公司(微软公司)的注册商标。 Windows为微软公司(微软公司)的注册商标。 其他产品名及公司的名称为各公司的商标或注册商标。 (C)富士施乐有限公司2004-2008 ---------------------------- <文件结束> -----------------------------