硕士论文中期报告
电 子 科 技 大 学
工程
路基工程安全技术交底工程项目施工成本控制工程量增项单年度零星工程技术标正投影法基本原理
硕士学位论文中期报告
学位论文题目:基于POS机的服装销售管理系统的设计与实现
工程领域名称: 计算机技术
学 号: 201151060103
姓 名:
校内导师姓名:
企业方导师姓名:
所 在 学 院: 计算机学院
电子科技大学研究生院制表
填表日期:2014年 2 月20 日
be based on a variety of geological conditions, through field Grouting test. (2) the flushing pressure: flush water pressure 80% of Grouting pressure, pressure 1MPa, 1MPa; rinse water pressure 50% Grouting pressure, pressure over 0.5MPa, 0.5MPa. (3) the cracks flush rushed to return after the end of 10min, and the length of time required, not less than 30min Burr hole, collusion with the holes of not less than 2H. On clarification of water are not up to the required hole section, should continue to wash, holes in the sediment thickness shall not exceed the remaining 20cm. (4) when the nearby are filling in holes or are close to filling the hole ends less than 24h, the fractured washing should not be conducted. (5) the filling hole (above) cracks after washing, the hole (above) should be immediately conducted a grout continuous operation, break interval over 24h for some reason, should be fractured again rinse before Grouting. 11.4.3 water pressure test (1) water pressure test should be carried out in the cracks after washing, according to instructions, using "easy water", "single point" and the "five-point" for water pressure test. (2) simple pressure test after the cracks flush flush or a combination of fissures. Pressure Grouting pressure 80%, if this value is greater than 1MPa, 1Mpa; water 20min, 5min read the water flow pressure, taking the final flow values were calculated flow, its results to permeability. Five-point and single-point method for water pressure test is executed in
电子科技大学博士/硕士学位论文
填 表 说 明
1、 研究生须认真填写本表相关
内容
财务内部控制制度的内容财务内部控制制度的内容人员招聘与配置的内容项目成本控制的内容消防安全演练内容
。
2、 中期考核一般在学位论文开题报告通过后半年左右进行。
3、 所列栏目填写不下的~可以另加附页。
4、 本表采取双面印制~且保持原格式不变~纸张限用 A4,页边距为上、下:2.5cm, 左为2.6cm,右为2.1cm,字体为宋体小四~行间距为18磅,~整齐装订。
5、 中期报告考核完成~经相关人员签字后~须交学院保存。be based on a variety of geological conditions, through field Grouting test. (2) the flushing pressure: flush water pressure 80% of Grouting pressure, pressure 1MPa, 1MPa; rinse water pressure 50% Grouting pressure, pressure over 0.5MPa, 0.5MPa. (3) the cracks flush rushed to return after the end of 10min, and the length of time required, not less than 30min Burr hole, collusion with the holes of not less than 2H. On clarification of water are not up to the required hole section, should continue to wash, holes in the sediment thickness shall not exceed the remaining 20cm. (4) when the nearby are filling in holes or are close to filling the hole ends less than 24h, the fractured washing should not be conducted. (5) the filling hole (above) cracks after washing, the hole (above) should be immediately conducted a grout continuous operation, break interval over 24h for some reason, should be fractured again rinse before Grouting. 11.4.3 water pressure test (1) water pressure test should be carried out in the cracks after washing, according to instructions, using "easy water", "single point" and the "five-point" for water pressure test. (2) simple pressure test after the cracks flush flush or a combination of fissures. Pressure Grouting pressure 80%, if this value is greater than 1MPa, 1Mpa; water 20min, 5min read the water flow pressure, taking the final flow values were calculated flow, its results to permeability. Five-point and single-point method for water pressure test is executed in
开题报告通过时间:2013年 月 日 中期报告提交时间:2014年 月 日 论文开题题目:
基于POS机的服装销售管理系统的设计与实现
论文中期题目:
基于POS机的服装销售管理系统的设计与实现
自2013年9月完成开题报告以来,按照开题报告中的
计划
项目进度计划表范例计划下载计划下载计划下载课程教学计划下载
展开研究。在侯孟书导师的指导下,论文的研究工作进展比较顺利。
(一)勤于查阅,广泛阅读,进一步奠定理论基础
为了做好研究,就必须熟悉在这一领域开展的研究和相应研究成果以及研究的趋势。阅读有关文献可以找到发现问题的方法,而且也是避免重复研究的方法。通过阅读文献,发现我国关于移动电子商务主要应用是在金融交易和银行业务。在未来几年中,移动电子商务的娱乐服务和游戏将成为全球的主导。其它的一些应用领域(如移动教育、移动供应管理)也值得涉足。但关于将硬件POS机的功能转换为软件并将其应用在商业上,目前是空白,因此基于POS机的管理系统值得深入探讨,同时在理论上也具备一定的商业价值。
同时在查阅相关文献的同时,对于Ruby on Rails的MVC网站框架、Saas模式、HTML5移动应用技术进行学习,为POS系统架构、开发实现打基础。 (二)深入企业调研,完成企业调研
该系统具有一定的商业价值,因此在2013年9月至12月,调研了大小十几家服装销售企业,与数十家都声称能提供销售管理服务的公司进行接触了解,展开了服装销售管理系统的具体工作。经过调研发现大部分服装零售行业存在投资小、网络网络覆盖多;终端以店中店、个体经营形式为主,固定网络无法全面支持,IT投资预算有限,而传统的POS机解决
方案
气瓶 现场处置方案 .pdf气瓶 现场处置方案 .doc见习基地管理方案.doc关于群访事件的化解方案建筑工地扬尘治理专项方案下载
依赖固定网络,投资大且运营维护成本高的问题。针对该类企业的需求,利用移动应用技术和云计算技术,通过整合智能平板电脑和无线网络来实现POS机功能的服务销售管理系统是非常必要的。
(三)通过问卷调查,进行方案论证
自2013年12月开始,根据不同规模的服装销售企业部门及不同受众,设计多个调查问卷,如大中型企业服装销售管理部需求
分析
定性数据统计分析pdf销售业绩分析模板建筑结构震害分析销售进度分析表京东商城竞争战略分析
问卷、销售终端需求分析问卷、服装批发商销售管理需求分析问卷、服装零售商销售管理需求分析问卷等,拟于2014年4月完成需求分析。
be based on a variety of geological conditions, through field Grouting test. (2) the flushing pressure: flush water pressure 80% of Grouting pressure, pressure 1MPa, 1MPa; rinse water pressure 50% Grouting pressure, pressure over 0.5MPa, 0.5MPa. (3) the cracks flush rushed to return after the end of 10min, and the length of time required, not less than 30min Burr hole, collusion with the holes of not less than 2H. On clarification of water are not up to the required hole section, should continue to wash, holes in the sediment thickness shall not exceed the remaining 20cm. (4) when the nearby are filling in holes or are close to filling the hole ends less than 24h, the fractured washing should not be conducted. (5) the filling hole (above) cracks after washing, the hole (above) should be immediately conducted a grout continuous operation, break interval over 24h for some reason, should be fractured again rinse before Grouting. 11.4.3 water pressure test (1) water pressure test should be carried out in the cracks after washing, according to instructions, using "easy water", "single point" and the "five-point" for water pressure test. (2) simple pressure test after the cracks flush flush or a combination of fissures. Pressure Grouting pressure 80%, if this value is greater than 1MPa, 1Mpa; water 20min, 5min read the water flow pressure, taking the final flow values were calculated flow, its results to permeability. Five-point and single-point method for water pressure test is executed in
电子科技大学博士/硕士学位论文
已完成工作是否符合开题报告中的内容要求:
是(?) / 否( )
(若选否,请对不符之处予以详细说明,如论文题目、主要理论、技术路线、实施方案等哪些方面有改动)
在论文工作中仍存在的困难和问题,拟采取的解决方案如下
(一)问卷调查时现场联系及质量控制
调查的企业规模、人员不同,且需根据实际情况进行调查,因此进行问卷调查时采用现场填写问卷的方式进行。进行现场调查时存在被调查者是否配合、问卷调查是否真实的问题。解决方案:(1)先联系相关企业负责人,请求支持。(2)在现场与被调查者进行交流、讨论,以便及时发现调查过程中遇到的问题,给予及时的指导,以提高调查质量。(3)现场调查根据现场情况采用多种形式,如座谈、一对一交流等形式。
(二)由于缺少实践经验,所作的访谈和调研不能完全体现系统的完整性、前瞻性、科学性,拟在与企业进行实际交流时进一步完善。
(三)在进行系统需求建模时,在理论结合实践方面需要进一步拓宽。因此打算在2014年4月前对理论分析的广度和深度上进一步完善。
be based on a variety of geological conditions, through field Grouting test. (2) the flushing pressure: flush water pressure 80% of Grouting pressure, pressure 1MPa, 1MPa; rinse water pressure 50% Grouting pressure, pressure over 0.5MPa, 0.5MPa. (3) the cracks flush rushed to return after the end of 10min, and the length of time required, not less than 30min Burr hole, collusion with the holes of not less than 2H. On clarification of water are not up to the required hole section, should continue to wash, holes in the sediment thickness shall not exceed the remaining 20cm. (4) when the nearby are filling in holes or are close to filling the hole ends less than 24h, the fractured washing should not be conducted. (5) the filling hole (above) cracks after washing, the hole (above) should be immediately conducted a grout continuous operation, break interval over 24h for some reason, should be fractured again rinse before Grouting. 11.4.3 water pressure test (1) water pressure test should be carried out in the cracks after washing, according to instructions, using "easy water", "single point" and the "five-point" for water pressure test. (2) simple pressure test after the cracks flush flush or a combination of fissures. Pressure Grouting pressure 80%, if this value is greater than 1MPa, 1Mpa; water 20min, 5min read the water flow pressure, taking the final flow values were calculated flow, its results to permeability. Five-point and single-point method for water pressure test is executed in
在总结前期研究工作的基础上,进一步明确任务,加强与导师的交流,通过导师的指导,将研究工作扎实推进,为高质量完成研究任务而努力。进度安排如下:
时间 内容
2014年2月,3月 完成需求分析问卷调查及资料收集。
2014年3月,4月 完成系统需求分析及POS系统开发模式及相应的
软件工程管理模式研究。
2014年4月,6月 完成标准方法构建服务、重用与整合服务的应用
模式的研究及POS系统的数据库设计、概要设计。
2014年6月,7月 完成POS系统设计。
2014年7,8月 完成测试计划、用例、测试报告等文档,完成POS
系统测试
2014年8,10月 撰写论文
导师对学生的研究态度、论文进展、工作能力、存在问题和论文后期工作计划等给予评价:
校内导师(组)(职称)签字: 年 月 日 企业方导师(职称)签字: 年 月 日 be based on a variety of geological conditions, through field Grouting test. (2) the flushing pressure: flush water pressure 80% of Grouting pressure, pressure 1MPa, 1MPa; rinse water pressure 50% Grouting pressure, pressure over 0.5MPa, 0.5MPa. (3) the cracks flush rushed to return after the end of 10min, and the length of time required, not less than 30min Burr hole, collusion with the holes of not less than 2H. On clarification of water are not up to the required hole section, should continue to wash, holes in the sediment thickness shall not exceed the remaining 20cm. (4) when the nearby are filling in holes or are close to filling the hole ends less than 24h, the fractured washing should not be conducted. (5) the filling hole (above) cracks after washing, the hole (above) should be immediately conducted a grout continuous operation, break interval over 24h for some reason, should be fractured again rinse before Grouting. 11.4.3 water pressure test (1) water pressure test should be carried out in the cracks after washing, according to instructions, using "easy water", "single point" and the "five-point" for water pressure test. (2) simple pressure test after the cracks flush flush or a combination of fissures. Pressure Grouting pressure 80%, if this value is greater than 1MPa, 1Mpa; water 20min, 5min read the water flow pressure, taking the final flow values were calculated flow, its results to permeability. Five-point and single-point method for water pressure test is executed in
电子科技大学博士/硕士学位论文
考评结论及意见:
通过( ) 不通过( )
考评专家组成员签字:
年 月 日 学院审批意见:
学院主管领导(签字、盖章):
年 月 日
be based on a variety of geological conditions, through field Grouting test. (2) the flushing pressure: flush water pressure 80% of Grouting pressure, pressure 1MPa, 1MPa; rinse water pressure 50% Grouting pressure, pressure over 0.5MPa, 0.5MPa. (3) the cracks flush rushed to return after the end of 10min, and the length of time required, not less than 30min Burr hole, collusion with the holes of not less than 2H. On clarification of water are not up to the required hole section, should continue to wash, holes in the sediment thickness shall not exceed the remaining 20cm. (4) when the nearby are filling in holes or are close to filling the hole ends less than 24h, the fractured washing should not be conducted. (5) the filling hole (above) cracks after washing, the hole (above) should be immediately conducted a grout continuous operation, break interval over 24h for some reason, should be fractured again rinse before Grouting. 11.4.3 water pressure test (1) water pressure test should be carried out in the cracks after washing, according to instructions, using "easy water", "single point" and the "five-point" for water pressure test. (2) simple pressure test after the cracks flush flush or a combination of fissures. Pressure Grouting pressure 80%, if this value is greater than 1MPa, 1Mpa; water 20min, 5min read the water flow pressure, taking the final flow values were calculated flow, its results to permeability. Five-point and single-point method for water pressure test is executed in