DEQ AIR QUALITY PROGRAM 1410 N. Hilton, Boise, ID 83706 For ...

DEQ AIR QUALITY PROGRAM 1410 N. Hilton, Boise, ID 83706 For ... DEQ AIR QUALITY PROGRAM Emissions Units – Automotive Coating Information Form EU6 1410 N. Hilton, Boise, ID 83706 Revision 5 For assistance, call the 2/22/11 Air Permit Hotline – 1-877-5PERMIT Complete this form for each paint booth. Please see instructions on page 2 before filling out the form. 1. Company Name 2. Facility Name: 3. Brief Project Description: 4. Booth Data: New Booth Unpermitted Existing Booth If an existing booth, when was it installed? Modification to a Permitted Booth, Permit #: Date Permit Issued: Dry Filters? Dry Filters w/ a Wet Wall? Wet Wall only? Other, provide details: Booth Airflow Type: Down draft Semi-Downdraft Side draft Other, provide details: 5. Booth Information: Manufacturer: Model: Date Manufactured: 6. Planned Construction Date (if applicable): 7. Is the booth equipped with a heater? No Go to the next section Yes If “yes”, answer the following questions. Heating method: Electricity, Go to the next section Combustion Who is the manufacturer of the booth heater? MMBtu/hr What is the model number of the booth heater? What is the heat input rating of the booth heater? MMBtu/hr What fuel is used in the booth heater (i.e., natural gas or LPG)? Is the worst-case operation of the booth heater greater than 2,080 hours per year? No Go to the next section Yes If “Yes”, what is the worse-case annual operation of the burner? hrs/yr 8. Are bed lining spray operations performed at this facility? No Go to the next section Yes, I am requesting an additional 4.0 gal/day limit for component “A” of a two stage “A + B” bed lining material. Transfer Efficiency % per 11. Type (e.g. HVLP, airless, 12. GunGun No. 9. Manufacturer 10. Model conventional) the manufacturer 1 2 3 4 13. Are you requesting a daily coating materials use permit limit (e.g. gallons per day)? Yes, I am requesting a limit of 4.0 gal/day for all coating materials used at the facility. Note: In order to receive an Automotive Coating general permit a daily materials use limit of 4.0 gal/day is required. No, Note: You will need to apply for a permit tailored to the situation at your facility, not an Automotive Coating general permit (see previous question). a,Stack Served 14. Filter Manufacturer 15. Model 16. PM Control Efficiency(%) 10 1 2 3 4 Note: a. Provide the filter manufacturer’s documentation to support the control efficiency specified above. 17. Is Methylene Chloride (MeCl) (CAS #75-09-2) used for paint stripping activities at this facility? No, Note: In order to receive an Automotive Coating general permit no MeCl paint stripping activities can be performed at the facility. Yes, Note: In order to receive an Automotive Coating general permit no MeCl paint stripping activities can be performed at the facility (see previous question). You will need to apply for a permit tailored to the situation at your facility, not an Automotive Coating general permit. Page 1 Instructions for Form EU6 1 – 3.Provide the same company name, facility name (if different), and brief project description as on Form GI. This is useful if application pages are separated. Note: If this is for an existing paint booth, just state that this project is to permit an existing automotive coating operation. USE ATTACHMENT IF ADDITIONAL SPACE IS REQUIRED. Paint Booth Information: 4. Check whether this booth is a new booth to be constructed, an unpermitted existing booth (as-built) applying for a permit for the first time, and the date of installation in which construction or modification begins as defined in EU0 Form Instruction item 7, or a permitted source to be modified along with the permit number and date issued. In addition, please specify the particulate matter control system used by the paint booth and the booth air-flow type. 5. Please provide the paint booth manufacturer, model, and the date the booth was manufactured. 6. Please provide the date of construction of the booth in month/day/year in which construction or modification begins as defined in EU0 Form Instruction item 7. Note: This date is not applicable for existing paint booths. 7. Please specify if the booth is equipped with a heater. If it is, please specify if electricity or combustion of fuel is used to heat the booth. If combustion is used, then specify the burner manufacturer, burner model number, and the heat input rating (per the data plate if so equipped or per the manufacturer’s information). In addition, specify the fuel used to fire the burner as well as the worst-case annual operation of the burner. 8. If bed lining operation are performed at the facility answer “yes” here. Please note as part of applying for the Automotive Coating general permit with a bed lining operation that bed lining materials will be limited to 4.0 gallons per day for component “A” of a two stage “A + B” bed lining material. Spray Gun Description and Specifications: 9. Specify manufacturer(s) of the spray gun(s) used in your booth. 10. Specify the model(s) of the spray gun(s). 11. Indicate the type of the gun(s). The type can be airless, HVLP, air atomization, electrostatic/air atomization, etc. 12. Indicate the transfer efficiency of the paint gun per the manufacturer. Please note that Federal requirements set a transfer efficiency of 65%. Request for Permit limitations: 13. If you wish to have a daily coating materials use permit limit placed on the paint booth, mark “Yes.” Please note that as part of applying for the Automotive Coating general permit a daily coating materials use limit of 4.0 gallons per day must be accepted by the Applicant. Emission Control Device (Filter) Description and Specifications: 14. Provide the name of the filter manufacturer. 15. Provide the model of the filter according to manufacturer's literature. 16. Provide the control efficiency for PM. Please note that Federal requirements set a PM control 1010 efficiency of 98%. Paint Stripping Activities: 17. Provide information as to whether Methylene Chloride (MeCl) (CAS #75-09-2) is used to strip paint at the facility. Please note that as part of applying for the Automotive Coating general permit the Applicant agrees that MeCl will not be used to strip paint at the facility. Page 2