Ks8028操作

Ks8028操作 Press (Runstop) to begin the welding. 5 3, perform Error: 224, 225 Item 6: skip this cup 7: skip this group 1 The electrode diagonography is not scanned 2 1. Scan not to the point, and according to item 3 B2 mobile electrode center again according to 1 B ON the first point according to B1, then moved to 2 B1 as shown in figure 2. Click ON the support Angle to point is wrong, according to item 3 B2 mobile scaffold diagonal point location according to 1 B (3) according to item 3 according to five new do to point and template, right-click photos, after the completion of the tip according to the ON error message: 390 left no bin error: 392 left bin is full error: 305 bin induced errors, or has reached the error: 408, 409, according to confirm the error message: error: 491 ON the right side of the bin with 431 right no bin error: operation key press 3, failure of the 180 burn ball f8 to open the clamp, according to wear line, in the corner bracket B1 tail off line, shift by + F6 to burn the ball, and according to 4 (B3 press 2 times to fill line), and then begin welding (Runstop). Error: 132 line, line (check the feeding system) error: induction is less than 260 (check for open temperature) temperature is less than 2: feeding position adjustment error: 262 3: perform clamp pressure is not enough (to check whether there is open source) 5: a row of six: the next set of error: 320, 7: the next row feeding position, adjust feeding position According to the 3 8 item: the claw is open The main menu is 3 to 2, 1 to 1 (CAuto), and then it moves over there, 1 3 6 2 After alignment of stent corner as shown in figure Adjust the press Done to move to the top right corner Angle to the good support click on the first cup B1 - OK - > Done - mobile scaffold click B3 take pictures, to press OK, B1, B3 - press OK - Done in the same place according to the error: 370, 327 left bin to have a stent (will stand back box then press 3) error: 146 height measurement test failure (press 3 stop welding, press shift + F7 height measurement, then press (Runstop) welding error: 800, 301, 315, 1. Motor error (fire the motor power from the drive motor, or the new boot) 2. Enter the 7-4 motor reset error: 615 TENSINER manual diagonal did not open, when prompted by three - by four to OFF error: 351, 349, table width is too small (enter 4-6-2 first and the second adjusting table width is too small) error: 428 429 bin parameter wrong (in 4-7-1 set of material box parameters too power is 1:170 2 items: 545, 3:5,800, 4:80, 5:2, 200, 6:25 Tip: when manual diagonal (Qpad. Bascd. A/ignmeuefaiLed) 3 and 4 in the second hand diagonal function did not open, ON as closed and OFF to open the application function is introduced 2, a welding programming - 3 3, 2 welding programming 1 the attachment 3 The ball (arc, pressure, work rate, time, burn ball) goes to 5 So 4 goes from PR to 8 7 7 - > 4 Adjust the temperature Under the top of the pressure plate (the parameters are large and the parameters are small) the lower pressure is adjusted (the parameters are small and the parameters are large). 4 - 6 - > 1 6 - > 2 Item 1: adjust platen width two: adjust platen width Action test 1 action test 7 Candy 11:47:20 The first fixture is 1: the workbench opens 1 item: the platen 1 item: the film Around 2 bin 4 motor reset Set the parameters to be programmed and then press 3 to 4 and 7 to select 1www Remove program 6-1-1 to select the program to be deleted, to select the program from Delvte, 3 to 1 to 3, According to the LONd wait for 3 to 5 minutes After the jump out of the program, such as a few minutes there are H \ Bpositiom modeREFEACH/move prompted to press 1 item to splint diagonal point 3-1-1 click OK to delete the surface process Candy 11:48:32 1 item: changed YCS 2 item: 2 3 items: 10 system scan welding points, such as scanning but manual to point 3 Five parameters "Do not add a golden ball, don't do this step, direct the 3-4 - (5-10 seconds) - 6 - according to the six parameters of the main menu 3-4 - (5-10 seconds) - 6 - according to the six - according to the two choice (pdsec 2) - according to item 3 (SSB - l LOOP) after 10 to 20 seconds to enter (add golden option) the first page to modify complete - > click on the Done,,,,, 6 a welding power, time, pressure The main menu press 3-4-6-3 to enter Wait five to ten seconds (one welding) seven; Power 85, 8; Time 15 9: pressure 35 Item 2: the arc height 25 3: reverse 20 4 items: 50 7:2 solder Angle 50 8 items: tightness -3 Item 4:60 Page 4 (EDIT: LOOP. Parnmotv) Page 1: Page 5: (ball one welding) two; Power 120, 3; Time 15, 4: pressure 35 The main menu is Done, Done, and the main menu is 3 to 4 (USG two welding) seven; Power 120; Time 15, 9: pressure 85 (SSB value 2 soldering) 6; Power 100, 7; Time 15, 8: pressure 30 Page 1: Page 2: Complete - > Done, Go eight golden ball size Settings The main menu press 3-4-6-7 into the adjustment Adjust good press Done to the main menu press 3-4-6-8 into the (BZTS) after the third ON Paragraphs 2, gold wire size 1.00 3, 4 items of golden ball size 2.4, burning ball 40 five power, burn time of 30 6, 10 eight tail wire length, value the golden ball size 2.5 To be OFF 4 9 save or Shift + F1 (3-1-4-2 -) into to the first and the second to the same number, Done in 10 porcelain tsui in good ceramic nozzle in the main menu 5-3-5-6 enter - 2 impedance (not more than 60 is normal) explain porcelain mouth has lock and press 3 save for porcelain mouth, according to the main menu after 5-3-1-2 into the press B1 B2 on ceramic nozzle seal position B3 and confirm - OK then B3 - OK - > Done welding line modification pause menu - > according to item 3, adjust, arc power, time, pressure, according to the five changes one or two solder joints (mobile location is not too big) : B1 confirmation line number, B2 change position, B3 modification to modify the good press Done (solder) main menu press 1 and 2 1, ONCE 2 items, 3 items from the first cup, the first line of the cup to start welding Alarm processing method Pause: press 6 for a single point, 7 items Error: (W/Hoper) according to the five - according to item 2 shown above (ON) for automatic feeding function, open (OFF) for don't open this function, press 1, 2, you can choose. (in the menu, shift + F4 to 5) Error: 326 catches no material to press 3 , paragraphs 1 and machines to grasp the case 2, drop one grab a material item 3, 4 items of clear material box, falling into a lattice 6 items, direction of the arrow to adjust up and down the five, exit menu box, press 2 June, height adjustment Error: 391 4, exit without material box on the right press 3 into five, explanation or the left box full error: 103 not burning ball, operation key press 3, press f8 to open the clamp, wear a good line, the angular point B1 in stent tail off line, press shift + F6 to burn the ball, and according to 4 (B3 press 2 times to fill line), and again KS8028PPS wire machine job instruction Function of keyboard corresponding screen F1 formula one - F10 - F10 F1: size screen switch F2: large screen zoom, narrowing the F3, a small screen magnification: F4: small screens to narrow F5: welding head back to the center position, F6: welding head reset F7: ultrasonic testing F8: clamp switch F9: lighting switch F10: LIGN 1, 2, ring lights 7 main light, set up 8, keep Sdue: save the shift + F1: save the shift + F3: sonfiguve item 1, 2, 3, to SHOW the shift + F4: WOVKHO item 4 is the workbench to open shift + F5: item 8 IMPUT (left bin) 1, left bin fell one OUTPUT (right material box), a 3, 2, rising material box out shift + F6: burning ball shift + F7: high in materials. When the porcelain mouth is on the high shift + F8: direction arrow to unlock Shift + F10: the grab arm, right grasp arm reset the first is pre-heat block temperature welding on the right heating block 1, 2, Motov stop operating keyboard motor power switch Runstop: start/pause, press the no reaction, press 1 and then press start Ihdex: feed/a piece of Autolndex: automatic a piece Bdck space: delete it one Escape: quit the mouse: B1 default, B2 B3 remove # 830 steps into the system boot light up to alert the press 1 - press 1 - press 1 and so on in a minute and then follow the prompt press 1, such as system bring up program (H/B posi Tim) message to the platen screen in 1 position according to B1, move to the position of 2 B1, then moved to the position according to B3 as shown in figure 3 one 2 3 Shift + F3: sonfiguve 1, 2, 3 changes to SHOW (open account shows the solder and line number) 2, the main menu of program 1 solder: 3 to 3, 3 to 1 to 1 to 1, click Netx to set the diagonal point, and press B1 for the straight stand point Diagonal position 1 2 3, 4, (after showing opvpont 2) and click Next, take pictures support Angle, the light is good, good box bracket angular point According to B1 - Netx - Netx, changing (VLL L1-1) item 1 to OFF, then B2 moving workbench to the first two joint press B1, second, third, fourth solder joints are according to B1, after the completion of the solder joints are 1, 2, 3, 4, as shown in figure 2 a - > Netx solder joints Press on the main menu: 3-3-2 - Netx electrode Angle on chip, as shown in figure: the first point in B1, the second click B1 (opvpont 2) show 2 - Netx 1 wafer electrode diagonals 2 2 Electrode Angle pictures for good chip, aimed at B1, click - Netx - Netx (U1-1) item 1 should become (padfinder) OFF, B2 move aimed at first a solder joint press B1, and moving on the second a solder joint press B1, three, designation for the solder joints, same finish four solder joints - Done - Done. 1 3 The wafer electrode is photographed Electrode one soldering bitmap 2 4 3 the attachment After the main menu press 3-4-1 to enter From two solder joints according to B1, B2 to move to a solder joint connected in B1, the first in the same line connection methods, 2, 3, 4 line (do not add a golden ball, from one connected to the second welding) welding 1, 2, 1, 3, 2, 4, 3, 4 Good connection to press the Done 4 copy According to the main menu after 3-7-8 into the six input (line), seven input 2 and 4 (column) - > click after nine, B2 moved to support the first click B1 as shown in figure 1 3 1 2 , then move to the diagonal support 2 click B1, the system will automatically move to the third click B1, completion of replication, eight solder joints, small screen - Done - click the nine - click on 9 - click 2 item, and click