模具英语专业术语
模具述语
一、入水:gate
进入位: gate location
水口形式:gate type
大水口:edge gate
细水口: pin-point gate
水口大小:gate size
转水口: switching runner/gate
唧嘴口径: sprue diameter
二、流道: runner
热流道: hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道:round(full/half runner
流道电脑分析:mold flow analysis
流道平衡:runner balance
热嘴: hot sprue
热流道板:hot manifold
发热管:cartridge heater
探针: thermocouples
插头: connector plug
插座: connector socket
密封/封料: seal
三、运水:water line
喉塞:line lpug
喉管:tube
塑胶管:plastic tube
快速接头:jiffy quick connector plug/socker
四、模具零件: mold components
三板模:3-plate mold
二板模:2-plate mold
边钉/导边:leader pin/guide pin
边司/导套:bushing/guide bushing
中托司:shoulder guide bushing
中托边 L:guide pin
顶针板:ejector retainner plate
托板: support plate
螺丝: screw
管钉:dowel pin
开模槽:ply bar scot
内模管位:core/cavity inter-lock
顶针: ejector pin
司筒:ejector sleeve
司筒针:ejector pin
推板:stripper plate
缩呵:movable core,return core core puller
扣机(尼龙拉勾):nylon latch lock
斜顶:lifter
模胚(架): mold base
上内模:cavity insert
下内模:core insert
行位(滑块): slide
镶件:insert
压座/斜鸡:wedge
耐磨板/油板:wedge wear plate
压条:plate
撑头: support pillar
唧嘴: sprue bushing
挡板:stop plate
定位圈:locating ring
锁扣:latch
扣鸡:parting lock set
推杆:push bar
栓打螺丝:S.H.S.B
顶板:eracuretun
活动臂:lever arm
分流锥:spure sperader
水口司:bush
垃圾钉:stop pin
隔片:buffle
弹弓柱:spring rod
弹弓:die spring
中托司:ejector guide bush
中托边:ejector guide pin
镶针:pin
销子:dowel pin
波子弹弓:ball catch
喉塞: pipe plug
锁模块:lock plate
斜顶:angle from pin
斜顶杆:angle ejector rod
尼龙拉勾:parting locks
活动臂:lever arm
复位键、提前回杆:early return bar
气阀:valves
斜导边:angle pin
术语:terms
承压平面平衡:parting surface support balance
模排气:parting line venting
回针碰料位:return pin and cavity interference
模总高超出啤机规格:mold base shut hight
顶针碰运水:water line interferes withejector pin
料位出上/下模:part from cavith (core) side
模胚原身出料位:cavity direct cut on A-plate,core direct cut
on B-plate.
不准用镶件: Do not use (core/cavity) insert
用铍铜做镶件: use beryllium copper insert
初步(正式)模图
设计
领导形象设计圆作业设计ao工艺污水处理厂设计附属工程施工组织设计清扫机器人结构设计
:preliinary (final) mold design
反呵:reverse core
弹弓压缩量:spring compressed length
稳定性好:good stability,stable
强度不够:insufficient rigidity
均匀冷却:even cooling
扣模:sticking
热膨胀:thero expansion
公差:tolorance
铜公(电极):copper electrode
Mold & die components 模具单元
Mold changing systems 换模系统
Mold core 模芯
Mold heaters/chillers 模具加热器/冷却器
Mold polishing/texturing 模具打磨/磨纹
Mold repair 模具维修
Molds 模具
Pressing dies 压模
Quick die change systems 速换模系统
Quick mold change systems 快速换模系统
三、模具
塑料模具 mould of plastics
注塑模具 injection mould
冲压模具 die
模架 mould base
定模座板 Top clamping plate
Top plate
Fixed clamp plate
水口推板 stripper plate
A 板 A plate
B 板 B plate
支承板 support plate
方铁 spacer plate
底针板 ejector plate
面针板 ejector retainer plate
回针 Return pin
导柱 Guide pin
有托导套 Shoulder Guide bush
直导套 Straight Guide bush
动模座板 Bottom clamp plate
Moving clamp plate
基准线 datum line
基准面 datum plan
型芯固定板 core-retainer plate
凸模固定板 punch-retainer plate
顶针 ejector pin
单腔模具 single cavity mould
多腔模具 multi-cavity mould
多浇口 multi-gating
浇口 gate
缺料 starving
排气 breathing
光泽 gloss
合模力 mould clamping force
锁模力 mould locking force
挤出 extrusion
开裂 crack
循环时间 cycle time
老化 aging
螺杆 screw
麻点 pit
嵌件 insert
活动镶件 movable insert
起垩 chalking
浇注系统 feed system
主流道 sprue
分流道 runner
浇口 gate
直浇口 direct gate , sprue gate
轮辐浇口 spoke gate , spider gate
点浇口 pin-point gate
测浇口 edge gate
潜伏浇口 submarine gate , tunnel gate
料穴 cold-slug well
浇口套 sprue bush
流道板 runner plate
排飞槽 vent
分型线(面)parting line
定模 stationary mould,Fixed mould
动模 movable mould, movable half
上模 upper mould, upper half
下模 lower mould, lower half
型腔 cavity
凹模 cavity plate,cavity block
拼块 split
定位销 dowel
定位销孔 dowel hole
型芯 core
斜销 angle pin, finger cam
滑块 slide
滑块导板 slide guide strip
楔紧块 heel block, wedge lock
拉料杆 sprue puller
定位环 locating ring
冷却通 cooling channel
脱模斜度 draft
滑动型芯 slide core
螺纹型芯 threaded core
热流道模具 hot-runner mould
绝热流道模 insulated runner mould
熔合纹 weld line (flow line)
三板式模具 three plate mould
脱模 ejection
换模腔模具 interchangeable cavity mould
脱模剂 release agent
注射能力 shot capacity
注射速率 injection rate
注射压力 injection pressure
差色剂 colorant
保压时间 holdup time
闭模时间 closing time
定型装置 sizing system
阴模 female mould,cavity block
阳模 male mould
电加工设备 Electron Discharge Machining
数控加工中心 CNC machine center
万能铁床 Universal milling machine
卧式刨床 Horizontal planer
车床 Engine lathe
平面磨床 Surface grinding machine
去磁机 Demagnetization machine
万能摇臂钻床 Universal radial movable driller
立式钻床 Vertical driller
超声波清洗机 Ultrasonic clearing machine
compre sion molding 压缩成型
flash mold 溢流式模具
plsitive mold 挤压式模具
split mold 分割式模具
cavity 型控 母模
core 模心 公模
taper 锥拔
leather cloak 仿皮革
shiver 饰纹
flow mark 流痕
welding mark 溶合痕
post screw insert 螺纹套筒埋值
self tapping screw 自攻螺丝
striper plate 脱料板
piston 活塞
cylinder 汽缸套
chip 细碎物
handle mold 手持式模具
(移转成型用模具)
encapsulation molding 低压封装成型
(射出成型用模具)
two plate 两极式(模具)
well type 蓄料井
insulated runner 绝缘浇道方式
hot runner 热浇道
runner plat 浇道模块
valve gate 阀门浇口
band heater 环带状的电热器
spindle 阀针
spear head 刨尖头
slag well 冷料井
cold slag 冷料渣
air vent 排气道
welding line 熔合痕
eject pin 顶出针
knock pin 顶出销
return pin 回位销反顶针
sleave 套筒
stripper plate 脱料板
insert core 放置入子
runner stripper plate 浇道脱料板
guide pin 导销
eject rod (bar)(成型机)顶业捧
subzero 深冷处理
three plate 三极式模具
runner system 浇道系统
stress crack 应力电裂
orientation 定向
sprue gate 射料浇口,直浇口
nozzle 射嘴
sprue lock pin 料头钩销(拉料杆)
slag well 冷料井
side gate 侧浇口
edge gate 侧缘浇口
tab gate 搭接浇口
film gate 薄膜浇口
flash gate 闸门浇口
slit gate 缝隙浇口
fan gate 扇形浇口
dish gate 因盘形浇口
diaphragm gate 隔膜浇口
ring gate 环形浇口
subarine gate 潜入式浇口
tunnel gate 隧道式浇口
pin gate 针点浇口
Runner less 无浇道
(sprue less)无射料管方式
long nozzle 延长喷嘴方式
sprue 浇口;溶渣
emboss 凸点
dome 凸圆
semi-shearing 半剪
stamp mark 冲记号
deburr or coin 压毛边
punch riveting 冲压铆合
side stretch 侧冲压平
reel stretch 卷圆压平
groove 压线
blanking 下料
stamp letter 冲字(料号)
shearing 剪断
tick-mark nearside 正面压印
tick-mark farside 反面压印
冲压名称类
extension dwg 展开图
procedure dwg 工程图
die structure dwg 模具结构图
material 材质
material thickness 料片厚度
factor 系数
upward 向上
downward 向下
press specification 冲床规格
die height range 适用模高
die height 闭模高度
burr 毛边
gap 间隙
weight 重量
total wt.总重量
punch wt.上模重量
五金零件类
inner guiding post 内导柱
inner hexagon screw 内六角螺钉
dowel pin 固定销
coil spring 弹簧
lifter pin 顶料销
eq-height sleeves=spool 等高套筒
pin 销
lifter guide pin 浮升导料销
guide pin 导正销
wire spring 圆线弹簧
outer guiding post 外导柱
stop screw 止付螺丝
located pin 定位销
outer bush 外导套
模板
个人简介word模板免费下载关于员工迟到处罚通告模板康奈尔office模板下载康奈尔 笔记本 模板 下载软件方案模板免费下载
类
top plate 上托板(顶板)
top block 上垫脚
punch set 上模座
punch pad 上垫板
punch holder 上夹板
stripper pad 脱料背板
up stripper 上脱料板
male die 公模(凸模)
feature die 公母模
female die 母模(凹模)
upper plate 上模板
lower plate 下模板
die pad 下垫板
die holder 下夹板
die set 下模座
bottom block 下垫脚
bottom plate 下托板(底板)
stripping plate 内外打(脱料板)
outer stripper 外脱料板
inner stripper 内脱料板
lower stripper 下脱料板
零件类
punch 冲头
insert 入块(嵌入件)
deburring punch 压毛边冲子
groove punch 压线冲子
stamped punch 字模冲子
round punch 圆冲子
special shape punch 异形冲子
bending block 折刀
roller 滚轴
baffle plate 挡块
located block 定位块
supporting block for location
定位支承块
air cushion plate 气垫板
air-cushion eject-rod 气垫顶杆
trimming punch 切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch 压筋冲子
reel-stretch punch 卷圆压平冲子
guide plate 定位板
sliding block 滑块
汪军锋 制作 029wangjunfeng@sina.com