cs-iosnaming

IOS Code Letter Feature a APPN a2 ATM a3 SNASW b Appletalk Routing c Remote Access Server d Desktop routing dsc Dial Shelf Controller g5 Enterprise Wireless (7200) g6 GPRS Gateway Support Node (7200) i IP routing i5 IP routing, no ISDN (mc3810) in Base IP (8500CSR) j Enterprise (kitchen sink routing) n IPX Routing (low-end routers) p Service Provider (or DOCSIS for uBR) r(x) IBM telco Telco w3 Distributed Director wp IP/ATM Base Image (8500MSR,LS1010) y/y5 IP Routing (low-end routers) (missing some IP routing/features like BGP) y7 IP/ADSL Last Updated: June 13, 2005 This reference is intended to assist engineers in ascertaining the feature sets included with an image. In most cases, the image name should correspond with the image name as downloaded from CCO. Assuming this to be the case, the image will have many numbers and letters in it, which indicate the feature functionality included in the image. The list below, while not "comprehensive," is a list of the most popular codes in a IOS naming convention. "Legacy naming" - Letters at the beginning 56i Encryption(DES) ent Plus (only when used with 'telco') k1 BPI k2/k8/k9 Encryption(DES=k8, 3DES=k9) o Firewall o3 Firewall/IDS s Plus, or "LAN Only" on Cat6K/7600 s2 Voice IP to IP Voice Gateway (26xx/36xx/37xx only) s3 "Basic" (limited IP routing, for limited-memory 26xx, 36xx) s4 "Basic" without switching s5 "Basic" without HD analog/AIM/Voice t Telco Return v VIP Support v3,v8 Voice (17xx) - v3=VOICE, v8=VOX w6 Wireless x(or x2) MCM l Runs from Flash m Runs from RAM z Compressed image "Legacy Naming" - Letters in the middle "Legacy Naming" - Letters at the end Notes - "Legacy Naming" Conventions 7200 and 7500 images for "IP Only" are always "IP Plus." Therefore, Base IP supports IP Gateway cards like the PA-VXC's, whereas in the 17/26/36/37xx's you need IP Plus. c7200-is-mz.121-11.bin - 12.1(11) mainline, IP Only (note: this is a 7200, so IP Plus = IP), runs from RAM and is a compressed image "Legacy Naming" - Feature Sets - Common Features Needed Plus - Needed for modems, ATM, voice (non-17xx), DLSw+. Also adds "back in" IP features not in low- end router "y" images, like BGP. VIP Support - Needed for VIP2/4/6 (75xx), FlexWAN (C6K) Desktop - Has IP, IPX, and usually AT. Some older IOS revs have DEC/LAT in there, too. Enterprise - "Kitchen Sink" - has every protocol possible, except those that require their own letter code. In the 1700, the "s" for PLUS feature sets sometimes is the first letter, as opposed in the middle, and the "y" for IP is sometimes at the end, instead of the beginning. Some sample decodes: c1700-bk2no3r2sv3y7-mz.121-5.YB5.bin - 12.1(5)YB2, AT/3DES/IPX/FW/IDS/IBM/Plus/Voice/IP/ADSL, runs from RAM and is a compressed image Image Name Feature Set cxxxx-ipbase-mz IP Base cxxxx-ipvoice-mz IP Voice cxxxx-advsecurityk9-mz Advanced Security (note k9=strong encryption) cxxxx-spservicesk9-mz Service Provider Services (note: also known as SP Services) cxxxx-entbase-mz Enterprise Base cxxxx-advipservicesk9-mz Advanced IP Services cxxxx-entservicesk9-mz Enterprise Services cxxxx-adventerprisek9-mz Advanced Enterprise Services New IOS Naming - Eight Feature Sets In early 2003, the IOS teams in Cisco redid the IOS feature sets to "pull in the reigns," so to speak, and get the whole granular list "boiled down" to just a few feature sets. This will (hopefully) make choosing a feature set easier as time moves on. Certain IOS feature sets that are "specials" - for instance, H.323/MCM, will always be separate. These sets were introduced first on the 1700, 2600XM, 2691, and 3700 series routers in 12.3 mainline. 12.3T will have only the new feature sets for these platforms and new ones. Later on, 12.2S and 12.3 special releases for the 7200, 10000, 12000, and other routers are planned to follow the same example. The key concept is "inheritance" - when you "move up" the diagram above, you "inherit" all the features from the feature sets below. For instance, Advanced IP Services combines the features in Advanced Security, Service Provider Services, IP Voice, and IP Base. Feature sets are easier to see their names, as well (substitute "2600" or "3700" or any other router model in place of "xxxx"): special note on Advanced IP Services: Notes - New IOS Naming With the transition to new feature sets, no doubt many end users will want to know what feature is in which feature set. For any installation, it is always recommended to first use the lookup tool known as Feature Navigator, located at http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp However, in a quick reference, please consult the following to figure out which feature set you need: IP Base - Entry-level image, rolls up into all other images. Provides core routing functionality, including static routes, RIP, OSPF, EIGRP, for IPv4 only. Includes modems (both analog and digital) trunking (802.1q and ISL) and DSL, which were previously premium services only obtainable in the "IP Plus" feature set. Also includes NAT. Advanced IP Services - Beyond merging Advanced Security and SP Services, it adds IPv6. The remaining feature sets mostly "add" lower sets together, and do little to no feature addition. A IP Voice - Adds VoIP and VoFR. Advanced Security - Adds IOS/Firewall, IDS, SSH, NAC, and IPSec (DES, 3DES, and AES). Service Provider Services - Adds Netflow, SSH, BGP, ATM, and VoATM. Enterprise Base - Adds support for "legacy" L3 protocols such as IPX and Appletalk. Also adds IBM features such as DLSw+, STUN/BSTUN, and RSRB.