AT070TN83_V.1

The copyright belongs to InnoLux. Any unauthorized use is prohibited. INNOLUX DISPLAY CORPORATION LCD MODULE SPECIFICATIONSPECIFICATIONSPECIFICATIONSPECIFICATION Customer: Model Name: AT070TN83 V.1 SPEC NO.: A070-83-TT-11 Date: 2007/05/11 Version: 01 □□□□Preliminary Specification ■■■■Final Specification Option ■ AT070TN83 V.1 LCM (TTL T-con with LED Driver) For Customer ’s Acceptance Approved by Comment INNOLUX The copyright belongs to InnoLux. Any unauthorized use is prohibited. InnoLux copyright 2004 All rights reserved, Copying forbidden. Record of Revision Version Revise Date Page Content Pre. Spec. 01 2006/12/05 Initial release. 02 2007/03/05 2 Add Note 1,2,3 Modify TTL connector model from “FH19S-40S-0.5SH” to “FH19SC-40S-0.5SH” 3 Add Note 4 Add “ I: input, O: output, P: power” 6 Add “Backlight Driving Conditions” 16 Add Note 4 18 Modify TTL connector model in the Mechanical Drawing Final-spec.01 2007/05/11 1 Modify backlight power consumption from “1.728W” to “2.500W”. Modify panel power consumption from “0.990W” to “0.825W”. 5 Add the Max.value of VLED. 6 Modify the Typ.value of Icc from”300mA” to “250mA” and Max.value from”350mA” to “300mA”. Modify “IL” to ”ILED” and the value from “180mA” to “500mA”. Add Max.value of ILED. Add Note 2,Note 3. Modify Note 5. 12 Modify test condition 1. 14 Modify Note 6. 19 Add the weight of corrugated board. INNOLUX The copyright belongs to InnoLux. Any unauthorized use is prohibited. Contents 1. General Specifications............................................................................................................1 2. Pin Assignment.......................................................................................................................2 3. Operation Specifications.........................................................................................................5 3.1. Absolute Maximum Ratings..............................................................................................5 3.2. Typical Operation Conditions...........................................................................................6 3.3. Power Sequence .............................................................................................................7 3.4. Timing Characteristics .....................................................................................................8 3.4.1. Timing Conditions....................................................................................................8 3.4.2. Timing Diagram .....................................................................................................10 4. Optical Specifications............................................................................................................12 5. Reliability Test Items.............................................................................................................16 6. General Precautions.............................................................................................................17 6.1. Safety .............................................................................................................................17 6.2. Handling .........................................................................................................................17 6.3. Static Electricity ..............................................................................................................17 6.4. Storage...........................................................................................................................17 6.5. Cleaning .........................................................................................................................17 7. Mechanical Drawing .............................................................................................................18 8. Package Drawing .................................................................................................................19 8.1. Packaging Material Table ...............................................................................................19 8.2. Packaging Quantity ........................................................................................................19 8.3. Packaging Drawing ........................................................................................................20 INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 1/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 1. General Specifications No. Item Specification Remark 1 LCD size 7.0 inch(Diagonal) 2 Driver element a-Si TFT active matrix 3 Resolution 800X3(RGB)X480 4 Display mode Normally white, Transmissive 5 Dot pitch 0.0635(W)X0.1905(H) mm 6 Active area 152.4 (W)X91.44 (H) mm 7 Module size 165(W)X104(H)X5.5(D) mm Note 1 8 Surface treatment Anti-Glare 9 Color arrangement RGB-stripe 10 Interface Digital(TTL) 11 Backlight power consumption 2.500W(Typ.) Note 3 12 Panel power consumption 0.825W(Typ.) Note 2 13 Weight 130g (Typ.) Note 1: Refer to Mechanical Drawing. Note 2: Including T-con Board power consumption. Note 3: Including LED Driver power consumption. INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 2/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 2. Pin Assignment TFT LCD Panel Driving Section TTL Connector is used for the module electronics interface. The recommended model is FH19SC-40S-0.5SH manufactured by Hirose. Pin No. Symbol I/O Function Remark 1 VLED P Power voltage for LED Driver 2 VLED P Power voltage for LED Driver 3 ADJ I Adjust the led brightness with PWM Pulse Note 1,2 4 GLED P Ground for LED circuit 5 GLED P Ground for LED circuit 6 VCC P Power voltage for digital circuit 7 VCC P Power voltage for digital circuit 8 MODE I DE or HV mode control Note 3 9 DE I Data enable 10 VS I Vsync signal input 11 HS I Hsync signal input 12 GND P Power ground 13 B5 I Blue data input (MSB) 14 B4 I Blue data input 15 B3 I Blue data input 16 GND P Power ground 17 B2 I Blue data input 18 B1 I Blue data input INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 3/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 19 B0 I Blue data input(LSB) 20 GND P Power ground 21 G5 I Green data input(MSB) 22 G4 I Green data input 23 G3 I Green data input 24 GND P Power ground 25 G2 I Green data input 26 G1 I Green data input 27 G0 I Green data input(LSB) 28 GND P Power ground 29 R5 I Red data input(MSB) 30 R4 I Red data input 31 R3 I Red data input 32 GND P Power ground 33 R2 I Red data input 34 R1 I Red data input 35 R0 I Red data input(LSB) 36 GND P Power ground 37 DCLK I Sample clock 38 GND P Power ground 39 L/R I Select left or right scanning direction Note 4 40 U/D I Select up or down scanning direction Note 4 I: input, O: output, P: power INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 4/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. Note1: ADJ adjust brightness to control Pin,Pulse duty the bigger the brighter. Note 2: ADJ signal=0~3.3V;Operating frequency:100~300Hz. Note 3: DE Mode: Mode=”H”, HS floating and VS floating. HV Mode: Mode=”L” and DE floating. Note 4: Selection of scanning mode Setting of scan control input U/D L/R Scanning direction GND VCC Up to down, left to right VCC GND Down to up, right to left GND GND Up to down, right to left VCC VCC Down to up, left to right INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 5/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 3. Operation Specifications 3.1. Absolute Maximum Ratings Values Item Symbol Min. Max. Unit Remark VCC -0.3 6.0 V Power voltage VLED - 5.5 V Input signal voltage VI -0.3 6.3 V Operation Temperature TOP -20 70 ℃ Storage Temperature TST -30 80 ℃ Note: The absolute maximum rating values of this product are not allowed to be exceeded at any times. A module should be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be recovered, or in an extreme condition, the module may be permanently destroyed. INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 6/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 3.2. Typical Operation Conditions Values Item Symbol Min. Typ. Max. Unit Remark VCC 3.1 3.3 3.5 V Note 1 Power voltage VLED 4.8 5.0 5.2 V Note 2 Icc - 250 300 mA Current consumption ILED - 500 550 mA Note 3 Input logic high voltage VIH 0.7VCC - VCC V Input logic low voltage VIL 0 - 0.3VCC V Note 4 LED life time - 20,000 - - Hr Note 5 Note 1: VCC setting should match the signals output voltage (refer to Note 4) of customer’s system board. Note 2: LED driving voltage. Note 3: LED driving current. Note 4: DCLK,DE, HS, VS, R0~ R5,,G0~ G5,B0~ B5. Note 5: The “LED life time” is defined as the module brightness decrease to 50% original brightness at Ta=25℃ and VLED=5.0V. The LED lifetime could be decreased if operating VLED is larger than 5.0V. INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 7/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 3.3. Power Sequence Power Supply Vcc Data Signal t 1 B/L t 2 t 3 t 1 t1 ＞＞＞＞ 50 mSec t2 ≧≧≧≧ 200 mSec t3 ≧≧≧≧ 200 mSec Note: Data Signal includes DCLK, DE, HS, VS, R0~ R5, G0~ G5, B0~ B5. INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 8/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 3.4. Timing Characteristics 3.4.1. Timing Conditions SYNC mode Input signal characteristics ( 800 x 480 ) Values Item Symbol Min. Typ. Max. Unit Remark Clock Period tCLK 20.0 30.0 - ns Clock Frequency fCLK - 33.3 50 MHz Clock Low Level Width tWCL 8 - - Clock High Level Width tWCH 8 - - Clock Rise/Fall Time tCLKr, tCLKf - - 3 ns HSYNC Period tHP - 928 - tCLK HSYNC Pulse Width tHW - 48 - tCLK HSYNC Back Porch tHBP - 40 - tCLK HSYNC Width + Back Porch thw + tHBP 88 tCLK Horizontal valid data width tHV 800 tCLK HSYNC Front Porch tHFP tHP - tHW - tHBP - tHV tCLK Horizontal Blank tHBK tHP - tHV tCLK VSYNC Period tVP - 525 - tHP VSYNC Pulse Width tVW - 3 - tHP VSYNC Back Porch tVBP 29 tHP Vertical valid data width tw 480 tHP Vertical Front Porch tVFP tVP - tVW - tVBP - tw tHP Vertical Blank tVBK tVP - tw tHP Data Setup Time tDS 5 - - ns Data Hold Time tDH 10 - - ns INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 9/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. DE mode Input signal characteristics ( 800 x 480 ) Values Item Symbol Min. Typ. Max. Unit Remark Period tCLK 20.0 30.0 - ns Frequency fCLK - 33.3 50 MHz Low Level Width tWCL 6 - - High Level Width tWCH 6 - - Rise/Fall Time tCLKr, tCLKf - - 3 ns DCLK Duty - 0.45 0.50 0.55 - tCLKL/ tCLK Setup Time tDES 5 - - Hold Time tDEH 10 - - Rise/Fall Time tDEr, tDEf - - 16 ns Horizontal Period tHP - 928 - Horizontal Valid tHV 800 Horizontal Blank tHBK tHP - tHV tCLK Vertical Period tVP - 525 - Vertical Valid tw 480 DE Vertical Blank tVBK tVP - tw tHP Setup Time tDS 5 - - Hold Time tDH 10 - - DATA Rise/Fall Time tDr, tDf - - 3 ns INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 10/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 3.4.2. Timing Diagram H s y n c D E t H B K t H W t H B P t H P t H V t H F P Input Vertical Timing Input Horizontal Timing INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 11/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. DE(RGB Data) t DEr( t Dr) t DEf( t Df) 0.7VDD 0.3VDD DE and RGB Input Timing INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 12/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 4. Optical Specifications Values Item Symbol Condition Min. Typ. Max. Unit Remark θL Φ=180°(9 o’clock) 60 70 - θR Φ=0°(3 o’clock) 60 70 - θT Φ=90°(12 o’clock) 40 50 - Viewing angle (CR≥ 10) θB Φ=270°(6 o’clock) 60 70 - degree Note 1 TON - 10 20 msec Note 3 Response time TOFF - 15 30 msec Note 3 Contrast ratio CR 400 500 - - Note 4 WX 0.26 0.31 0.36 - Color chromaticity WY 0.28 0.33 0.38 - Note 2 Note 5 Note 6 Luminance L 250 300 - Cd/m2 Note 6 Luminance uniformity YU Normal θ=Φ=0° 70 75 - % Note 7 Test Conditions: 1. VCC=3.3V, VLED=5.0V.The ambient temperature is 25 .℃ 2. The test systems refer to Note 2. INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 13/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. Note 1: Definition of viewing angle range Fig. 4-1 Definition of viewing angle Note 2: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 30 minutes operation, the optical properties are measured at the center point of the LCD screen. (Response time is measured by Photo detector TOPCON BM-7, other items are measured by BM-5A/Field of view: 1° /Height: 500mm.) Fig. 4-2 Optical measurement system setup Normal line θ=Φ=0° Φ=90° 12 o’clock direction Φ=270° 6 o’clock direction Φ=0° Φ=180° Active Area θL θT θB θR Normal line θ=Φ=0° Photo detector Φ=90° 12 o’clock direction Φ=270° 6 o’clock direction Φ=0° Φ=180° Active Area 500mm LCM LCM INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 14/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. Note 3: Definition of Response time The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the time between photo detector output intensity changed from 10% to 90%. Fig. 4-3 Definition of response time Note 4: Definition of contrast ratio state Black"" the on LCD whenmeasured Luminance state White"" the on LCD whenmeasured Luminance (CR) ratio Contrast = Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel. The LED driving condition is VLED=5.0V. 100% 90% 10% 0% P h o to d e te c to r o u tp u t (R e la ti v e v a lu e ) TON TOFF White (TFT OFF) Black (TFT ON) White (TFT OFF) INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 15/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. Note 7: Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every measuring point is placed at the center of each measuring area. max min B B (Yu)Uniformity Luminance = L-------Active area length W----- Active area width W W /3 W /3 W /6 L/3L/3L/6 L Fig. 4-4 Definition of measuring points Bmax: The measured maximum luminance of all measurement position. Bmin: The measured minimum luminance of all measurement position. INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 16/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 5. Reliability Test Items (Note3) Item Test Conditions Remark High Temperature Storage Ta = 80 240 hrs℃ Note 1 Low Temperature Storage Ta = -30 ℃ 240hrs Note 1 High Temperature Operation Ts = 70 240hrs℃ Note 2 Low Temperature Operation Ta =-20 ℃ 240hrs Note 1,Note 4 Operate at High Temperature and Humidity +40 , 90%RH max. ℃ 240 hrs Note 4 Thermal Shock -30 /30 min ~ +℃ 80 /30 min for a total 100 ℃ cycles, Start with cold temperature and end with high temperature. Note 4 Vibration Test Frequency range:10~55Hz Stroke:1.5mm Sweep:10Hz~55Hz~10Hz 2 hours for each direction of X. Y. Z. (6 hours for total) Mechanical Shock 100G 6ms,±X, ±Y, ±Z 3 times for each direction Package Vibration Test Random Vibration : 0.015G*G/Hz from 5-200HZ, -6dB/Octave from 200-500HZ 2 hours for each direction of X. Y. Z. (6 hours for total) Package Drop Test Height:60 cm 1 corner, 3 edges, 6 surfaces Electro Static Discharge ± 2KV, Human Body Mode, 100pF/1500Ω Note 1: Ta is the ambient temperature of samples. Note 2: Ts is the temperature of panel’s surface. Note 3: In the standard condition, there shall be no practical problem that may affect the display function. After the reliability test, the product only guarantees operation, but doesn’t guarantee all the cosmetic specification. Note 4: Before cosmetic and function test, the product must have enough recovery time, at least 2 hours at room temperature. INNOLUX SPEC NO.: A070-83-TT-11 PAGE: 17/20 The copyright belongs to InnoLux. Any unauthorized use is prohibited. 6. General Precautions 6.1. Safety Liquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your skin or clothes, wash it off immediately by using soap and water. 6.2. Handling 1. The LCD panel is plate glass. Do not subject the panel to mechanical shock or to excessive force on its surface. 2. The polarizer attached to the display is easily damaged. Please handle it carefully to avoid scratch or other damages. 3. To avoid contamination on the display surface, do not touch the module surface with bare hands. 4. Keep a spac