JHD529M1

JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 1PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS CUSTOMER APPROVAL P/N: JHD529M1 APPROVALCHECKEDCHECKED CUSTOMER: SUPPLIER APPROVAL APPROVALCHECKEDCHECKED Tel：86-755-83674016;86-755-61361995 Fax：86-755-83779544 Address：Room A512, Baohua office building, Shenzhen, P.R.China E-mail: jhd2@baohua.com.cn Website: www.jhdlcd.com.cn JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 2PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS ALLINITIAL RELEASE31/05/051 REMARKPAGEDESCRIPTION OF REVISIONREV. DATEREV. NO. •REVISION RECORD JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 3PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS CONTENTS 1. FEATURES ……………………………………………...........................…. 2. MECHANICAL SPEC ……………………………………………………..…. 3. ABSOLUTE MAXIMUM RATING ………………………..…………………. 4. ELECTRICAL CHARACTERISTICS …..…………………………………… 5. ELECTRO-OPTICAL CHARACTERISTICS .…………...…………………. 6. QC/QA PROCEDURE ......………………………………...………………... 7. RELIABILITY .……...…………………………………………………..……... 8. BLOCK DIAGRAM ..……………………………………………………….… 9. POWER SUPPLY …………………..……………………………………….. 10. TIMIING DIAGRAM ……………………………….…..………….……….... 11. AC CHARACTERISTICS……………………………………………………. 12. INSTRUCTION SET ……..…………….………………………..…………... 13. HANDLING PRECAUTION.……..……..…………………………………... 14. EXTERNAL DIMENSION .....……..…………………………….………….. 15. INTERFACE .....……..…………………………….………………………….. 4 4 5 5 6 7 8 9 9 10 11 12 14 17 18 JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 4PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS •Display construction…………… •Display mode ……………………… •Display type ……………………… •Viewing direction………………… •Operating temperature…………… •Driving voltage…………………… •Driving method……………………… •Type…………………………………… •Number of data line……………… •Connector…………………………… 128*64 DOTS STN / Yellow Green Positive Transmissive 6 o’clock Indoor Single power 1/33 duty, 1/6bias COB (Chip On Board) 8-bit parallel Pin gAbout 50Weight mm2.7Diameter of mounting hole mm-0.52 0.52 Pitch mm-0.48 0.48 Size Dot mm-38.8 70.7 Viewing area mm12.7(MAX)70.0 93.0 Module size UNITTHICKNESSHEIGHTWIDTHITEM 1. FEATURES 2. MECHANICAL DATA JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 5PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS 3. ABSOLUTE MAXIMUM RATINGS 4. ELECTRICAL CHARACTERISTICS JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 6PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS 5. ELECTRO-OPTICAL CHARACTERISTICS q q Æ Æ Top Bottom Left R ight V iew ing Surface Top View ing Angle V iew ing Angle Bottom Please select e ither top or bottom v iew ing angle Note 3: Definition of Viewing Angle Note 1: Definition of Contrast Ratio “K” Note 2: Definition of Optical Response Time K= 10% 90% Brightness Curve of selected area Brightness Curve of non-selected area Vop Driving Voltage B rig ht ne ss Brightness of non-selected segment(A) A B Brightness of selected segment(B) Non-selected Selected Non-selected 100% 0% Brightness 90% 10% Rise Time Fall Time -30 -- +30θ 3deg. -40 -- +40 K ≥2.0 φ Viewing angle 2ms350250φ=0TfResponse time (fall) 2ms300250-φ=0TrResponse time (rise) 1--41.4φ=0KContrast ratio NOTEUNITMAX.TYP.MIN.CONDITIONSYMBOLITEM JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 7PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS 6. QC/QA PROCEDURE Parts QA Dept. LCD Mfg. Dept. LCM QA Dept. Parts Soldering Soldering Inspection Parts Acceptance Inspection LCM Assembling High Temp. Test Heat Cycle Aging Inspection Storage/Shipping Outgoing Inspection Packaging 1. Function & Appearance & Dimension: Sample Test 2. Reliability: Random Sampling Soldering Condition 1. Dimension: Sample Test 2. Function: 100% Inspection -10~60℃ (1 Cycle=6 Hrs). 2 Cycle: 100% Inspection Function & Appearance: 100% Inspection (ex. 50℃) 1. Function & Appearance: 100% Inspection 2. Dimension: Random Sampling Package Condition & Label: 100% Inspection 1. Function,Appearance & Dimension: Random Sampling 2. Package Product & Label: Random Sampling 3.Electro-optical Characteristic: 100% Inspection 4. Reliability: Random Sampling JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 8PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS •Operating life time: Longer than 50000 hours (at room temperature without direct irradiation of sunlight) •Reliability Characteristics: 1.Operating time: Thirty minutes exposure in each direction (x, y, z) 2.Sweep Frequency (1min):10Hz→ 55Hz →10Hz 3.Amplitude: 0.75mm double amplitude Vibration -10℃→25℃→60℃→25℃ /5 Cycles (30min) (5min) (30min) (5min) Thermal shock 40℃ * 90%RH / 200 HrsHigh humidity -10℃ / 200 HrsLow temp. nTotal current consumption should be below double of initial value nContrast ratio should be within initial value±50% nNo defect in cosmetic and operational function is allowable 60℃ / 200 HrsHigh temp CriterionTestItem 7. RELIABILITY JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 9PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS 8. BLOCK DIAGRAM & 9.POWER SUPPLY 256X 32 JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 10PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS 10. TIMING DIAGRAM JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 11PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS 11. AC CHARACTERISTICS JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 12PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS 12. INSTRUCTION SET JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 13PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 14PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS 13. Handling Precautions 1. Limitation of Application: Optrex products are designed for use in ordinary electronic devices such as business machines, telecommunications equipment,measurement devices and etc. Please handle the products with care. (see below) Optrex products are not designed,intended ,or authorized for use in any application which the failure of the product could result in a situation where personal injury or death may occur . these applications include, but are not limited to . life-sustaining equipment,nuclear control devices , aerospace equipment , devices related to hazardous or flammable materials , etc.[If Buyer intends to purchase or use the Optrex Products for such unintended or unauthorized applications , Buyer must secure prior written consent to such use by a responsible officer of Optrex Corporation.]Should Buyer purchase or use Optrex Products for any such unintended or unauthorized application [ without such consent ].Buyer shall indemnify and hold Optrex and its officers. employees. subsidiaries, affiliates and distributors harmless against all claims, costs, damages and expenses , and reasonable attorney’s fees,arising out of , directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Optrex was negligent regarding the design or manufacture of the part. 2.Industrial Rights and Patents Optrex shall not be responsible for any infringement of industrial property rights of third parties in any country arising out of the application or use of Optrex products, except which directly concern the structure or production of such products. If pressure to LCD, orientation may be disturbed. LCD will broken by shock! Liquid Crystal may be leaked when display is broked. If it accidentally gets your hands, wash then with water! No Press and Shock! Don’t Swallow or Touch Liquid Crystal! Don’t not Scratch! No DC Voltage to LCD! Polarizer is a soft material and can easily be scratched. DC No! DC volrage or driveing higher than the specified voltage will reduce the lifetime of the LCD. JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 15PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS be reshaped, which will conductive rubber may LCD may be shifted or cause defects. Pressure on the metallic frame and PCB may deform the conductive rubber or break the liquid crystal cell and back light, which will cause defects. Don’t Press the Metallic Frame and Disassemble the LCM Avoid static electricity. Slowly Peel Off Protective Film! Please be sure to ground human body and electric apploances during work. It is preferable to use conductive mat on table and wear cotton clothes or conduction processed fiber. Synthetic fiber is not recommended. Avoid Static Electricity! Wear Gloves While Handing! LCD deteriorates. Keep Away From Extreme Heat and Humidity! When attaching with the heat seal or anisontropically conductive film, wipe off with alcohol before use. Alcohol Use Alcohol to Clean Terminals! GLOVE It is preferable to wear gloves to avoid damaging the LCD. Please do not touch electrodes with bare hands or make them dirty. JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 16PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS Note that the presence of waterdrops or dew in the LCD panel may deteriorate the polarizer or corrade electrode. Don’t Drop Water on LCD! Precaution in Soldering LCD Module Basic instructions: Solder I/O terminals only. Use soldering iron without leakage. (1)Soldering condition to I/O terminals Temperature at tip of the iron: 280±10℃ Soldering time: 3~4 sec. Type of solder: Eutectic solder (containing colophony-flux) *Please do not use flux because it may soak into LCD Module or contaminate it. *It is preferable to peel off protective film on display surface after soldering I/O terminals is finished. (2)Remove connector or cable *When you remove connector or cable soldered to I/O terminals, please confirm that solder is fully melted. If you remove by force, electrodes at I/O terminals may be damaged(or stripped off). *It is recommended to use solder suction machine. Long-term Storage If it is necessary to store LCD modules for a long time, please comply with the following procedures. If storage condition is not satisfactory, display(especially polarizer) may be deteriorated or soldering I/O terminals may become difficult(some oxide is generated at I/O terminals plating). 1.Store as delivered by Optrex 2.If you store as unpacked,put in anti-static bag,seal its opening and store where it is not subjected to direct sunshine nor fluorescent lamp. 3.Store at temperature 0 to +35℃ and at low humidity.Please refer to our specification sheets for storage temperature range and humidity condition. Long-term Storage Please use power supply with built-in surge protection circuit. JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 17PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS 14. EXTERNAL DIMENSION JHD529M1 LCD MODULE SPECIFICATION FOR APPROVAL 18PAGE 1.1VER. 31/05/05DATE JHD ELECTRONICS 15. INTERFACE PIN NO. SYMBOL DESCRIPTION FUNCTION 1 VSS GROUND 0V (GND) 2 VDD POWER SUPPLY FOR LOGIC CIRCUIT +5V 3 V0/VDD/NC LCD CONTRAST ADJUSTMENT OR LCD VOLTAGE OR NC 4 D/I INSTRUCTION/DATA REGISTER SELECTION D/I = 0 : INSTRUCTION REGISTER D/I = 1 : DATA REGISTER 5 R/W READ/WRITE SELECTION R/W = 0 : REGISTER WRITE R/W = 1 : REGISTER READ 6 E ENABLE SIGNAL 7 DB0 8 DB1 9 DB2 10 DB3 11 DB4 12 DB5 13 DB6 14 DB7 15 PSB SERIAL/PARALLEL SELECTION PSB=0:SERIAL MODE PSB=1:8/4BIT PARALLEL BUS MODE 16 NC 17 RST RESET SIGNAL RSTB=0,DISPLAY OFF,DISPLAY FROM LINE 0. 18 VEE/NC LCD DRIVE VOLTAGE/NC 19 A SUPPLY VOLTAGE FOR LED+ +5V 20 K SUPPLY VOLTAGE FOR LED- 0V DATA INPUT/OUTPUT LINES 8 BIT: DB0-DB7