Materials
What you’ll need to get started
on your D.I.Y. Project
DIY Carpet kit (includes knee kicker, knife & tucking tool)
Underlay
Carpet
Tools
Knee Pads & Goggles
Hammer
Measuring Tape
Carpet Gripper (Smoothedge)
Joining Tape (if required)
Safety
Use kneepads to protect knees and goggles for hammering in nails. Use gloves if
necessary when handling the carpet gripper due to the sharp pins protruding.
Planning your next
D.I.Y. Project
The Bunnings D.I.Y. brochures are designed to help you step
the way through your D.I.Y. home projects.
They’ll give you the right advice on what materials you’ll need,
how to get the job done and tips and ideas for achieving
the best result.
For more information go to
bunnings.com.au
How to
Install Carpet
BU
N
N
794 03/09
Expert D.I.Y. advice
If it’s advice you’re after, come in and discuss the project with
one of our experts. Ask about organising Same Day Delivery, Tool Hire,
Installation or even enrol in one of our D.I.Y. classes.
How to install carpet
D.I.Y.
FREE
How to D.I.Y.
Install Carpet
Decorate a room with new
carpet. Carpet is a soft
textile that adds warmth
and colour to any room.
Choose from a range of
textures, styles and colours
available and add value
to your home. DIY carpet,
the solution to your fl ooring
needs.
Please Note:
Information in this brochure is Bunnings’ opinion and we don’t warrant
the accuracy or completeness of that information. Bunnings excludes all
liability in relation to the statements in this brochure.
Here’s a guide for cutting:
– for cut pile (twist & plush) carpet - cut along back of carpet with a utility
knife
– for loop pile carpet - cut through the face of your carpet
Take a measurement of your room and cut about 100 to 150mm extra so
that you have some excess carpet.
Attaching the carpet to the gripper
Now you’re ready to hook the carpet onto the
gripper strips. You’re ready to use the knee
kicker! Starting on one wall, push the teeth of
the knee kicker into the carpet approximately
25 – 50mm from the wall. Kick the cushioned
end of the knee kicker with your knee. This will
fi rmly hook the carpet onto the gripper strip.
In addition to this you can use a hammer to
fi rmly ‘rub’ along the carpet pushing it on to
the gripper strips. Continue along each wall
anchoring the carpet on to the carpet gripper
Stretching Using the Kicker
Using the knee kicker, stretch the length and the width of the carpet until
reasonably tight – do not ‘over kick’ with the kicker as it may rip the
carpet.
Trimming & Tucking
Once the carpet has been stretched onto the gripper, trim the excess carpet
off leaving approximately 10 – 15mm of carpet for tucking. Tuck the 10-
15mm of carpet down between the skirting board and gripper using the
tucking tool – this gives a nice smooth fi nish.
If required, fi t a doorway trim at the doorway to fi nish of the carpet to the
doorway.
Glueing Carpet Directly To the Floor
Carpet can be directly stuck to the sub-fl oor using the appropriate carpet
adhesive. This method is useful for areas where more then one width of
carpet is required, therefore avoiding heat seaming joins.
Follow the directions on the adhesive container for best results.
D.I.Y. Hints and Tips
1. When pulling up old carpet, cut in to one metre wide strips to make it
easier to get out of the room.
2. If skirting boards require painting, paint them after removing old
carpet so painting can go all the way to the bottom of the board –
allow curing time before installing new carpet.
Preparing your fl oors
Installing carpet begins with preparing your fl oors. If you have a wooden
fl oor, a thorough sweep or vacuum should do the trick. Nail down any loose
fl oorboards. If you have ducted heating, fi nd out where exactly the ducts are
so that you can cut the holes out after the carpet has been installed.
Measuring the room
Using the Bunnings on line fl ooring estimator or measuring pads in store,
measure the length and width of the room to determine the quantity of carpet
required – NOTE: take in to account the width of carpet product purchased.
Installing the carpet
Installing the carpet gripper (smoothedge)
The fi rst step in laying carpet is to install the
carpet gripper. Cut the gripper strip to fi t the
length of each wall. You’re going to nail the
strips around each wall, leaving about 8 -12
mm between the strip and the wall. Nail the
strip using the nails pre-fi tted in the strip. The
pins should point toward the wall. Make sure
that the strips join together at the corners of
the room. For concrete fl oors, use concrete
gripper; for timber fl oors, use timber gripper
– noted on the box at point of purchase.
Installing the underlay
The next step is to install the underlay. You need to cut the underlay in lengths
long enough to reach the carpet gripper. Staple the carpet underlay every
150mm to secure it to the fl oor. If your fl oor is concrete, you’ll need to spot
glue the underlay to the fl oor using any carpet adhesive. Let the adhesive dry
completely before moving on to the next step in order to prevent the underlay
from bunching up under the carpet as you fi t it. Remember that the underlay
should not overlap, but rather butt together. Cover seams with tape. Cut off
any excess underlay with a knife.
Place the carpet in to the room
When placing the carpet in to the room for installation, be careful of painted
surfaces as the carpet backing may graze paint. Roll carpet out ready for
cutting and fi tting.
Joining carpet
If the room being carpeted is bigger than the width of the carpet then a
join is required. A simple method is to use wide pre-glued tape with peel of
backing. Using this restricts the amount of stretching of the carpet using the
kicker as it may cause the join to come apart. Commercially available heat
irons and heat bond tape can be used if required.
Cutting the carpet
When cutting the carpet, you need to remember a few points regarding the
texture of your carpet. The pile should always face in the same direction,
make sure that the pile faces one direction — usually toward the main
doorway is the preferred direction.
For further expert advice consult the qualifi ed Team Members at your
local Bunnings Warehouse.
<<
/ASCII85EncodePages false
/AllowTransparency false
/AutoPositionEPSFiles true
/AutoRotatePages /None
/Binding /Left
/CalGrayProfile (Dot Gain 20%)
/CalRGBProfile (sRGB IEC61966-2.1)
/CalCMYKProfile (U.S. Web Coated \050SWOP\051 v2)
/sRGBProfile (sRGB IEC61966-2.1)
/CannotEmbedFontPolicy /Error
/CompatibilityLevel 1.4
/CompressObjects /Tags
/CompressPages true
/ConvertImagesToIndexed true
/PassThroughJPEGImages true
/CreateJDFFile false
/CreateJobTicket false
/DefaultRenderingIntent /Default
/DetectBlends true
/DetectCurves 0.0000
/ColorConversionStrategy /CMYK
/DoThumbnails false
/EmbedAllFonts true
/EmbedOpenType false
/ParseICCProfilesInComments true
/EmbedJobOptions true
/DSCReportingLevel 0
/EmitDSCWarnings false
/EndPage -1
/ImageMemory 1048576
/LockDistillerParams false
/MaxSubsetPct 100
/Optimize true
/OPM 1
/ParseDSCComments true
/ParseDSCCommentsForDocInfo true
/PreserveCopyPage true
/PreserveDICMYKValues true
/PreserveEPSInfo true
/PreserveFlatness true
/PreserveHalftoneInfo false
/PreserveOPIComments true
/PreserveOverprintSettings true
/StartPage 1
/SubsetFonts true
/TransferFunctionInfo /Apply
/UCRandBGInfo /Preserve
/UsePrologue false
/ColorSettingsFile ()
/AlwaysEmbed [ true
]
/NeverEmbed [ true
]
/AntiAliasColorImages false
/CropColorImages true
/ColorImageMinResolution 300
/ColorImageMinResolutionPolicy /OK
/DownsampleColorImages true
/ColorImageDownsampleType /Bicubic
/ColorImageResolution 300
/ColorImageDepth -1
/ColorImageMinDownsampleDepth 1
/ColorImageDownsampleThreshold 1.50000
/EncodeColorImages true
/ColorImageFilter /DCTEncode
/AutoFilterColorImages true
/ColorImageAutoFilterStrategy /JPEG
/ColorACSImageDict <<
/QFactor 0.15
/HSamples [1 1 1 1] /VSamples [1 1 1 1]
>>
/ColorImageDict <<
/QFactor 0.15
/HSamples [1 1 1 1] /VSamples [1 1 1 1]
>>
/JPEG2000ColorACSImageDict <<
/TileWidth 256
/TileHeight 256
/Quality 30
>>
/JPEG2000ColorImageDict <<
/TileWidth 256
/TileHeight 256
/Quality 30
>>
/AntiAliasGrayImages false
/CropGrayImages true
/GrayImageMinResolution 300
/GrayImageMinResolutionPolicy /OK
/DownsampleGrayImages true
/GrayImageDownsampleType /Bicubic
/GrayImageResolution 300
/GrayImageDepth -1
/GrayImageMinDownsampleDepth 2
/GrayImageDownsampleThreshold 1.50000
/EncodeGrayImages true
/GrayImageFilter /DCTEncode
/AutoFilterGrayImages true
/GrayImageAutoFilterStrategy /JPEG
/GrayACSImageDict <<
/QFactor 0.15
/HSamples [1 1 1 1] /VSamples [1 1 1 1]
>>
/GrayImageDict <<
/QFactor 0.15
/HSamples [1 1 1 1] /VSamples [1 1 1 1]
>>
/JPEG2000GrayACSImageDict <<
/TileWidth 256
/TileHeight 256
/Quality 30
>>
/JPEG2000GrayImageDict <<
/TileWidth 256
/TileHeight 256
/Quality 30
>>
/AntiAliasMonoImages false
/CropMonoImages true
/MonoImageMinResolution 1200
/MonoImageMinResolutionPolicy /OK
/DownsampleMonoImages true
/MonoImageDownsampleType /Bicubic
/MonoImageResolution 1200
/MonoImageDepth -1
/MonoImageDownsampleThreshold 1.50000
/EncodeMonoImages true
/MonoImageFilter /CCITTFaxEncode
/MonoImageDict <<
/K -1
>>
/AllowPSXObjects false
/CheckCompliance [
/None
]
/PDFX1aCheck false
/PDFX3Check false
/PDFXCompliantPDFOnly false
/PDFXNoTrimBoxError true
/PDFXTrimBoxToMediaBoxOffset [
0.00000
0.00000
0.00000
0.00000
]
/PDFXSetBleedBoxToMediaBox true
/PDFXBleedBoxToTrimBoxOffset [
0.00000
0.00000
0.00000
0.00000
]
/PDFXOutputIntentProfile ()
/PDFXOutputConditionIdentifier ()
/PDFXOutputCondition ()
/PDFXRegistryName ()
/PDFXTrapped /False
/Description <<
/CHS
/CHT
/DAN
/DEU
/ESP
/FRA
/ITA
/JPN
/KOR
/NLD (Gebruik deze instellingen om Adobe PDF-documenten te maken die zijn geoptimaliseerd voor prepress-afdrukken van hoge kwaliteit. De gemaakte PDF-documenten kunnen worden geopend met Acrobat en Adobe Reader 5.0 en hoger.)
/NOR
/PTB
/SUO
/SVE
/ENU (Use these settings to create Adobe PDF documents best suited for high-quality prepress printing. Created PDF documents can be opened with Acrobat and Adobe Reader 5.0 and later.)
>>
/Namespace [
(Adobe)
(Common)
(1.0)
]
/OtherNamespaces [
<<
/AsReaderSpreads false
/CropImagesToFrames true
/ErrorControl /WarnAnd
本文档为【How_to_install_carpet】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑,
图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。