Bates_House纸模

Fold Guide Optional - Cut out windows (leaving the center rails). Build the window inserts and glue in place behind each window and door opening. Note - “Mother” is in the front, top, left window. 5B 5B 8A Insert tabs through slots and glue down tabs Apply a small amount of glue to top corners and top edges. Insert tabs through slots of 5A, 2B and 2C. DO NOT GLUE DOWN TABS YET! Score and fold the edges of 5A, 2B and 2C as shown. Apply a small amount of glue to bottom corners and top edges of roof parts 6A and 6B. Position roof parts so TABS ARE OUTSIDE (see inset)! When roof is in position, glue down tabs. 2B 2C 5A 6B 6B 6A 6A Apply a small amount of glue to top corners and edges. Apply a small amount of glue to bottom corners and edges. Assemble roof parts 6A and 6B. TABS ARE OUTSIDE! 4A 1A 3A 2A 2A 3A 7A 7B A Please note that this project is not recommended for children. It requires a moderate degree of skill, and the use of a cutting blade, which is extremely dangerous. When using cutting blades always use protective eyewear. This model was designed to be printed on Matte Paper Heavyweight, and the use of white glue is recommended. Black dashed lines represent a mountain fold (a fold which point upward), and orange dashed lines represent a valley fold (the fold points downward). The orange dashed lines are accompanied by a red “+” at each end. These are to be used as pin guides. Poke small holes at the “+”, flip the sheet over, and score between the holes for a clean valley fold. Read the instructions and study the illustrations carefully before beginning. A free project from http://www.haunteddimensions.raykeim.com B Apply a small amount of glue to bottom corners and top edges of tower roof 5C. Position roof parts so TABS ARE OUTSIDE (see inset)! When roof is in position, glue down tabs. 5C 5C 8E 8D 8C 4H 4C 8B 4J 4J 4B 6C Completed Model 6C 4B 4B x 2 6C x 2 4F & 4G 4F & 4G 4D4D 4iAssemble tower roof parts 5C and dormer 4D. Insert tabs in slot then glue down tabs. Attach beneath side door. Attach to side of porch. Apply glue to tabs then insert. TABS ARE OUTSIDE! 1 of 9 slots "Mother" window Porch 7B here 1A 3A4A 2 of 9 slots slots slots 2A 2C 2B A free project from http://www.haunteddimensions.raykeim.com 3 of 9 3A Attach piece 2A here A free project from http://www.haunteddimensions.raykeim.com 4 of 9 to 3A 4A 4B 4B 4C 4D 4i 4H 4J 4F 4G slots A free project from http://www.haunteddimensions.raykeim.com 5 of 9 slots slots slots slots slots5C 5A 5B A free project from http://www.haunteddimensions.raykeim.com 6 of 9 slots slotsslots slotsslots slots 6A Front Back 6B 6C 6C A free project from http://www.haunteddimensions.raykeim.com 7 of 9 7A 7B A free project from http://www.haunteddimensions.raykeim.com slots slots 8 of 9 8A 8B* 8B 8D* 8C* 8C 8E 8E* 8D 8A* * for optional transparency printing A free project from http://www.haunteddimensions.raykeim.com 9 of 9 Mother Side Door Front Door Tower front Towerside Optional window inserts A free project from http://www.haunteddimensions.raykeim.com