数控生产设备--中英文翻译

数控生产设备--中英文翻译 南通职业大学毕业 设计 领导形象设计圆作业设计ao工艺污水处理厂设计附属工程施工组织设计清扫机器人结构设计 、 Numerical control (NC) is a form of programmable automation in which the processing equipment is controlled by means of numbers, letters, and other symbols. The numbers, letters, and symbols are coded in an appropriate format to define a program of instructions for a particular workpart or job. When the job changes, the program of instructions is changed. The capability to change the program is what makes NC suitable for low-and medium-volume production. It is much easier to write new programs than to make major alterations of the processing equipment. A numerical control system consists of the following three basic components: ?Program of instructions ?Machine control unit ?Processing equipment 第1页 共16页 南通职业大学毕业设计 The general relationship among the three components is illustrated in Fig.2.1. The program is fed into the control unit, which directs the processing equipment accordingly. The program of instructions is the detailed step-by-step commands that direct the processing equipment. In its most common form, the commands refer to positions of a machine tool spindle with respect to the worktable on which the part is fixtured. More advanced instructions include selection of spindle speeds, cutting tool, and other function. The most common medium in use over the last several decades has been 1-in. -wide punched tape. Because of the widespread use of the punched tape, NC is sometimes called “tape control”. However, this is a misnomer in modern usage of numerical control. Coming into use more recently have been magnetic tape cassettes and floppy diskettes. The machine control unit (MCU) consists of the electronics and control hardware that read and interpret the program of instruction and convert it into mechanical actions of the machine tool or other processing equipment. The processing equipment is the third basic component of an NC system. It is the component that performs useful work. In the most common example of numerical control, one that performs 第2页 共16页 南通职业大学毕业设计 machining operations, the processing equipment consists of the worktable and spindle as well as the motors and controls needed to drive them. There are two basic types of control systems in numerical control: point-to-point and contouring. In the point-to-point system, also called positioning, each axis of the machine is driven separately by leadscrews and, depending on the type of operation, at different velocities. The machine moves initially at maximum velocity in order to reduce nonproductive time but decelerates as the tool reaches its numerically defined position. Thus in an potation such as drilling or punching, the positioning and cutting take place sequentially. After the hole is drilled or punched, the tool retracts, moves rapidly to another position, and repeats the operation. The path followed from one position to another is important in only one respect: The time required should be minimized for efficiency. Point-to-point systems are used mainly in drilling, punching, and straight milling operations. In the contouring system, also known as the continuous path system, positioning and cutting operations are both along controlled paths but at different velocities. Because the tool 第3页 共16页 南通职业大学毕业设计 cuts as it travels along a prescribed path, accurate control and synchronization of velocities and movements are important. The contouring system is used on lathes, milling machines, grinders, welding machinery, and machining centers. Movement along the path, or interpolation, occurs incrementally, by one of several basic methods. In all interpolations, the path controlled is that of the center of rotation of the tool. Compensation for different tools, different diameter tools, or tool wear during machining, can be made in the NC program. There are a number of interpolation schemes that have been developed to deal with the various problems that are encountered in generating a smooth continuous path with a contouring-type NC system. They include: ?Linear interpolation ?Circular interpolation ?Helical interpolation ?Parabolic interpolation ?Cubic interpolation Each of these interpolation procedures permits the programmer (or operator) to generate machine instructions for linear or curvilinear paths, using a relatively few input parameters. The 第4页 共16页 南通职业大学毕业设计 interpolation module in the MCU performs the calculations and directs the tool along the path. Linear interpolation is the most basic and is used when a straight-line path is to be generated in continuous-path NC. Two-axis and three-axis linear interpolation routines are sometimes distinguished in practice, but conceptually they are the same. The program is required to specify the beginning point and end point of the straight line, and the feed rate that is to be followed along the straight line. The interpolator computes the feed rates for each of the two (or three) axes in order to achieve the specified feed rate. Linear interpolation for creating a circular path would be quite inappropriate because the programmer would be required to specify the line segments and their respective end points that are to be used to approximate the circle. Circular interpolation schemes have been developed that permit the programming of a path consisting of a circular arc by specifying the following parameters of the arc: the coordinates of its end points, the coordinates of its center, its radius, and the direction of the cutter along the arc. The tool path that is created consists of a series of straight-line segments, but the segments are calculated by the interpolation 第5页 共16页 南通职业大学毕业设计 module rather than the programmer. The cutter is directed to move along each line segment one by one in order to generate the smooth circular path. A limitation of circular interpolation is that the plane in which the circular arc exists must be a plane defined by two axes of the NC system. Helical interpolation combines the circular interpolation scheme for two axes described above with linear movement of a third axis. This permits the definition of a helical path in three-dimensional space. Parabolic and cubic interpolation routines are used to provide approximations of free-form curves using higher-order equations. They generally require considerable computational power and are not as common as linear and circular interpolation. Their applications are concentrated in the automobile industry for fabricating dies for car body panels styled with free-form designs that cannot accurately and conveniently be approximated by combining linear and circular interpolations. A program for numerical control consists of a sequence of directions that causes an NC machine to carry out a certain operation, machining being the most commonly used process. Programming for NC may be done by an internal programming 第6页 共16页 南通职业大学毕业设计 department, on the shop floor, or purchased from an outside source. Also, programming may be done manually or with computer assistance. The program contains instructions and commands. Geometric instructions pertain to relative movements between the tool and the workpiece. Processing instructions pertain to spindle speeds, feeds, tools, and so on. Travel instructions pertain to the type of interpolation and slow or rapid movements of the tool or worktable. Switching commands pertain to on/off position for coolant supplies, spindle rotation, direction of spindle rotation, tool changes, workpiece feeding, clamping, and so on. (1) Manual Programming Manual part programming consists of first calculating dimensional relationships of the tool, workpiece, and work table, based on the engineering drawings of the part, and manufacturing operations to be performed and their sequence. A program sheet is then prepared, which consists of the necessary information to carry out the operation, such as cutting tools, spindle speeds, feeds, depth of cut, cutting fluids, power, and tool or workpiece ally a paper tape is first prepared for trying out and debugging the 第7页 共16页 南通职业大学毕业设计 program. Depending on how often it is to be used, the tape may be made of more durable Mylar. Manual programming can be done by someone knowledgeable about the particular process and able to understand, read, and change part programs. Because they are familiar with machine tools and process capabilities, skilled machinists can do manual programming with some training in programming. However, the work is tedious, time consuming, and uneconomical-and is used mostly in simple point-to-point applications. (2) Computer-Aided Programming Computer-aided part programming involves special symbolic programming languages that determine the coordinate points of corners, edges, and surfaces of the part. Programming language is the means of communicating with the computer and involves the use of symbolic characters. The programmer describes the component to be processed in this language, and the computer converts it to commands for the NC machine. Several languages having various features and applications are commercially available. The first language that used English-like statements was developed in the late 1950s and is called APT (for Automatically Programmed Tools). This language, in its various expanded forms, 第8页 共16页 南通职业大学毕业设计 is still the most widely used for both point-to-point and continuous-path programming. Computer-aided part programming has the following significant advantages over manual methods: ? Use of relatively easy to use symbolic language ?Reduced programming time. Programming is capable of accommodating a large amount of data concerning machine characteristics and process variables, such as power, speeds, feed, tool shape, compensation for tool shape changes, tool wear, deflections, and coolant use. ? Reduced possibility of human error, which can occur in manual programming ? Capability of simple changeover of machining sequence or from machine to machine. ? Lower cost because less time is required for programming. Selection of a particular NC programming language depends on the following factors: a) Level of expertise of the personnel in the manufacturing facility. b) Complexity of the part. c) Type of equipment and computers available. d) Time and costs involved in programming. 第9页 共16页 南通职业大学毕业设计 Because numerical control involves the insertion of data concerning workpiece materials and processing parameters, programming must be done by operators or programmers who are knowledgeable about the relevant aspects of the manufacturing processes being used. Before production begins, programs should be verified, either by viewing a simulation of the process on a CRT screen or by making the part from an inexpensive material, such as aluminum, wood, or plastic, rather than the material specified for the finished part 数字控制是用数字、字母和其他控制字符进行编程，来实现机械设备 自动化的一种形式。号码，字母和符号是为特定的工作环境或工作而 设定的一种适当的内编码。根据程序指示的改变，机械的加工也随之 改变方式。更易改写程序的优越性使NC系统更适合加工微小体积的产品。与更换生产设备相比，通过编辑新的程序来实现产品的加工要 容易得多。 一个数控系统包括以下3个基本零部件： （1）指示程序 （2）机器控制单元 第10页 共16页 南通职业大学毕业设计 （3）机床 三者的关系如下图。 指示程序 机器控制单元 机 床 机床根据输入计算机的程序来执行相应的动作。详细的指示程序直接 控制机床一步一步的执行命令。在通常情况下，刀具参考点的指令与 工作台的机床原点位置有关。更先进的指令系统包括机床进给速度的 选择，切削工具和其他功能。在过去几十年里最常用的信息载体是1 英寸宽的穿孔纸带。因为穿孔纸带的广泛使用，NC系统有时也叫“带子控制”，不过，这是现代用法过程中对数字控制的误称。近年来， 卡型盒式磁带和软磁盘开始广泛使用。 机器控制单元（MCU）由读取并理解程序说明，进而将程序转变成机 床或另外生产设备可执行的机械动作所需的硬件和电子元件组成。 机床是NC系统中的第3个基本零部件。它是有用的执行部件，在数 字控制的最普通的例子里，进行机器加工操作就是其中之一，机床由 工作台、主轴和控制主轴所必须的驱动电机组成。 在数字控制过程中有两类基本的控制系统：点位控制和轮廓控制。点 位控制也被称作为位置控制，通过电机以不同的速度分别驱动机器的 各轴，这取决于操作的方式。为了减少空操作的时间，机器在最初是 以最大速度移动，但在刀具到达设定的位置时，要降低速度，这样， 第11页 共16页 南通职业大学毕业设计 在进行过程中，如钻孔或打洞的操作是在准确的位置进行持续切削。 在钻孔或打洞后，刀具退回并迅速移动到另一个位置进行重复操作。 从一点大另一点的路径是一个重要的方面：为提高效率，要求移动时 间降到最小。点位控制系统主要用于钻孔、打洞及直线磨削等方面。 在轮廓控制，也就是所谓的连续路径运行系统中，位置的确定和切削 操作同时沿着设定的路径以不同的速度运行。因为当刀具沿着 规定 关于下班后关闭电源的规定党章中关于入党时间的规定公务员考核规定下载规定办法文件下载宁波关于闷顶的规定 的 路径切削进给时，准确控制速度和运动的同步性是相当重要的，连续 切削控制用于车床、铣床、磨床、焊接机器和机械加工中心。 沿路径运动或位置插补是几种基本的方法之一。在整个插补过程中， 路径控制以刀具的转动为中心。对于不同的刀具补偿，不同的刀具， 及在机器加工过程中刀具的磨损，都能通过NC程序进行调节。 有许多插补程序被开发用于处理连续切削控制系统中形成光滑、连续 的轨迹所遇到的各种各样的问 题 快递公司问题件快递公司问题件货款处理关于圆的周长面积重点题型关于解方程组的题及答案关于南海问题 ，他们包括： ? 直线插补 ? 圆弧插补 ? 螺旋线插补 ? 抛物线插补 这些插补程序是程序员（或操作员）用来生成直线或曲线路径的机器 指令，以相对减少输入饿参数。在MCU方面的插补模式进行计算并按 指定的路径执行。 第12页 共16页 南通职业大学毕业设计 直线插补是最基本的方法，在NC系统中生成连续轨迹时经常用到。 在实践中，两轴和三轴直线插补有时有所区别，但他们的原理是相同 的。程序被要求指定直 线的起点和终点，及沿着直线跟随的进给量，为了取得被指定的进给 量，插补器为两轴（或三轴）中的每个轴计算插补量。 因为程序员要求指定的直线部分和将用来接近圆的各自的终点有差 别，用直线插补生成圆弧轨迹不适合。圆弧插补程序被开发用于圆弧 插补，通过指定组成圆弧轨迹的下列参数：终点、中心、半径。刀具 沿着圆弧的指示坐标进给，被生成的刀具轨迹由一系列直线部分组 成。只是这部分是用插补模块来计算，而不是由程序员预先给定。为 了生成光滑的圆弧轨迹，切削刀具被指定沿着每段直线一步一步的进 给。圆弧插补的局限性在用两轴NC系统加工飞机部件时有所体现。 螺旋线插补是结合应用第三轴的直线运动和圆弧插补的两轴运动，这 就定义了三维空间的螺旋轨迹。 抛物线插补是使用高命令方程式得到的近似值所生成的自由形式的 曲线，他一般需要相当多的计算功能，并且与普通的直线和圆弧插补 不同。他们应用于汽车制造业，适合建立因内应力集中而导致车体损 坏，对那些不能准确计算用以生成自由形式的小汽车的设计，这样可 以方便地通过结合直线和圆弧的插补来接近设计要求。 第13页 共16页 南通职业大学毕业设计 数控程序由指导一台NC机器进行某种操作的一连串命令组成。机械 加工是最常见的方式，NC编程可以由内部的编程部门完成，或者从 外面购买。此外，编程可以是手工或计算机辅助完成。 程序包括命令和说明。几何学说明刀具和工件之间的有关运动；设备 说明有关主轴的速度，进给，刀具等；行程说明属于哪类型的插补及 刀具和工作台移动的快慢，接通命令说明开/关冷却剂的非工作状态，旋转及其方向，刀具的更换，工件的进给，夹具等方面。 （1）人工编程 人工零件编程由先计算刀具、工件和工作台之间的 相对位置，基于零件的 工程 路基工程安全技术交底工程项目施工成本控制工程量增项单年度零星工程技术标正投影法基本原理 图，以及执行生产操作的顺序等组成。然 后准备的图表包含执行操作的各种必要信息。比如切削刀具，主轴速 度、进给，切削深度，切屑，驱动及刀具和工件间的相对位置和运动。 有了这些基本的信息，零件程序准备就绪。 通常先准备一盘纸带用来调试程序。带子可能用更耐用的Mylar材料做成，这取决于它被使用的频率。 人工程序由那些专门的编程员钟对特别的生产而编辑，以变化零件加 工过程，因为熟悉机床功能和工序，熟练的机械师能在编程过程中得 到某些训练，不过，工作是乏味、费时和不经济的，而且主要是简单 的点对点应用。 （2） 计算机辅助编程 计算机辅助零件涉及确定刀具落点，刀具 切削刃，零件表面等有特别象征的程序语言，程序语言是与计算机进 行信息交流的一种方法，其中包含标志符号的使用。程序员用这种语 言对生产加以描述，而计算机把这种语言转化成NC机器能识别的指 第14页 共16页 南通职业大学毕业设计 令，在市场上有各种各样象征和应用的几种语言可买，使用 英语 关于好奇心的名言警句英语高中英语词汇下载高中英语词汇 下载英语衡水体下载小学英语关于形容词和副词的题 那样 陈述的第一种语言在20世纪50年代末被发展成为APT（自动编程工具）。这种语言发展成了各种形体，仍被广泛应用于点位和连续切削。 计算机辅助零件编程与手工方法相比有以下优点： ? 使用相对易于使用的符号语言； ? 减少编程时间。程序能提供大量关于机器特性的数据和处理变量， 例如驱动，速度，进给，刀具形状，对工具形状的补偿，刀具磨损， 挠度及冷却剂的使用； ? 降低在人工编程中可能发生的人为错误的可能性； ? 从机器顺序的简单切换加工能力； ? 因减少编程时间而降低成本。 一种特别的NC程序语言的选择取决于下列因素： （a）生产过程中人员的专门技能水平； （b）零件的复杂程度； （c）可提供的计算机和设备型号； （d）编程涉及的时间和费用。 因为NC系统与工件材料和过程参数的插入有关，程序必须由懂得生 产设备使用相关方面知识的专门人员编辑，在投入使用前，程序应进 行调试，通过CRT屏幕 观看用一种廉价材料加工零件的模拟过程，例如铝，木头或者塑料， 而不是适合成品生产的指定素材。 第15页 共16页 南通职业大学毕业设计 第16页 共16页