数控机床m代码含义

数控机床m代码含义 M00 程序停 ;M00 Programmable stop ;M01 程序选择停 ;M01 Selective programmable stop ;M03 主轴顺时针转 ;M03 Rotate spindle clockwise ;M04 主轴逆时针转 ;M04 Rotate spindle counterclockwise ;M05 主轴停 ;M05 Spindle stop ;M06 换刀* ;M06 Tool change Start * ;M09 切削液关(所有) ;M09 Coolant off (all coolants) ;M10 B轴夹紧 ;M10 Clamp B-axis ;M11 B轴松开 ;M11 Unclamp B-axis ;M12 Start pallet change * ;M12 托盘交换* ;M20 A轴夹紧 ;M20 Clamp A-axis ;M21 A轴松开 ;M21 Unclamp A-axis ;M51 变量:穿过主轴冷却液 ;M51 VARIANT: High pressure coolant through spindle ;M52 变量:淋浴冷却液 ;M52 VARIANT: Coolant shower ;M53 VARIANT: Air through spindle on (on I y when minimum quantity lubrication) M53 变量:穿过主轴空气开(只有当最小量润滑时) ;M54 VARIANT: Minimum quantity lubrication on M54 最小量润滑开 ;M55 穿过主轴冷却液监控开 ;M55 VARIANT: High pressure coolant monitoring on ;M56 穿过主轴冷却液监控关 ;M56 VARIANT: High pressure coolant monitoring off M57 选择:过程测量开 ;M57 OPTION: In process measuring on M58 选择:过程测量关 ;M58 OPTION: In process measuring off ;M59 设定工件, ;M59 Set part is machined ;M61 托盘 夹紧* ;M61 Clamp pallet * 松开* ;M62 托盘 ;M62 Unclamp pallet * ;M65 钻空检查* ;M65 OPTION check drill * ;M69 托盘交换完成* ;M69 Pallet change finished * ;M71 换刀门关闭 ;M71 Close tool change door ;M72 换刀门打开 ;M72 Open tool change door ;M75 钻头断刀控制: 检查立刻放下刀具, ;M75 OPTION drill break control: check lay down tool immediately ;M76 刀具断刀控制: 检查被标记的刀具, ;M76 OPTION tool break control: check tool of marked place * ;M77 刀具断刀控制:放下刀具时在刀库区作标记 ;M77 OPTION tool break control: mark magazine place of lay down tool * ;M78 钻头断刀控制检查* ;M78 OPTION check drill break control * ;M85 Umspeichermerker Spindel --> Magazin 1 setzen * ;M85 Restore flag spindle --> set magazine 1 * ;M86 Umspeichermerker Spindel --> Magazin 1 ruecksetzen * ;M86 Restore flag spindle --> reset magazine 1 * ;M87 Werkzeugmagazin freigeben von Bearbeitung ;M87 Enable tool magazine from machining ;M88 装刀启动* ;M88 Toolload started * ;M89 卸刀启动* ;M89 Tool unload started * ;M90 装刀 /卸刀 完成* ;M90 Toolload I unload finished * ;M91 刀具卡爪关闭* ;M91 Close tool gripper * ;M92 刀具卡爪打开* ;M92 Open tool gripper * ;M93 主轴紧刀* ;M93 Clamp spindle collet * ;M94 主轴松刀* ;M94 Unclamp spindle collet * ;M96 主轴速度监控关* ;M96 Spindle speed monitoring off * ;M97 主轴速度监控开* ;M97 Spindle speed monitoring on * ;M98 打开循环计时器 ;M98 Start cycle time counter ;M99 关闭循环计时器 ;M99 Stop cycle time counter ; ; ;M151 选择切削液5bar ;M151 OPTION selection coolant 5 bar ;M152 选择切削液10bar ;M152 OPTION selection coolant 10 bar ;M153 选择切削液17bar ;M153 OPTION selection coolant 17 bar ;M154 选择切削液25bar ;M154 OPTION selection coolant 25 bar ;M155 选择切削液33bar ;M155 OPTION selection coolant 33 bar ;M156 选择切削液40bar ;M156 OPTION selection coolant 40 bar ;M157 选择切削液50bar ;M157 OPTION selection coolant 50 bar ;M161 VARIANT: Minimum quantity lubrication select pressure step 1 M161 最小量润滑选择压力1 ;M162 VARIANT- Minimum quantity lubrication select pressure step 2 M162 最小量润滑选择压力2 ;M163 VARIANT: Minimum quantity lubrication select pressure step 3 M163 最小量润滑选择压力3 ;Erweiterte M-Funktionen XHC 241 SIN 840D ;============================================================= ; ;M1=44 以手动断刀检测为条件启动* ;M1=44 OPTION: Check start conditions for manual tool break control * ;M1=45 以手动断刀检测循环完成* ;M1=45 OPTION: Cycle manual tool break control finished * ;M1=48 Freigabe Vorrichtung entkuppeln ;M1=49 暖机程序完成 * ;M1=49 OPTION: Warm-up program finished * ;M1=50 托盘交换循环启动* ;M1=50 Pallet change cycle started * ;M1=51 预先控制托盘夹紧* ;M1=51 Precontrol clamp pallet * ;M1=52 预先控制托盘放松* ;M1=52 Precontrol unclamp pallet * ;M1=53 左侧装置冲洗 * ;M1=53 PCH rinse lifting device * ;M1=54 Z轴进给启动(相反的程序)* ;M1=54 Feed enable Z-axis start from reverse program * ;M1=55 Z轴进给停止(相反的程序)** ;M1=55 Feed enable Z-axis stop from reverse program * ;M1=56 Startvoraussetzung fuer Palettenwechsel fehlt * ;M1=56 Start condition for pallet change missing * ;M1=57 激活断刀控制* ;M1=57 Activate tool break control * ;M1=58 在断刀后取消刀具交换 ;M1=58 Cancel tool change from tool break control * ;M1=59 Pruefen ob Altplatz an Wechselstelle * ;M1=59 Check if old place at change position * ;M1=60 OPTION: Spare for BLUM drill break control laser on * ;M1=61 OPTION- Spare for BLUM drill break control laser off * ;M1=62 OPTION: Spare for BLUM drill break control open cap * ;M1=63 OPTION: Spare for BLUM drill break control close cap * ;M1=64 启动主轴切削液 ;M1=64 Start blow off coolant from spindle ;M1=65 停止主轴切削液 ;M1=65 Stop blow off coolant from spindle ;M1=66 REV (Freifahrprogramm) NC-Kanal 1 begonnen * ;M1=66 REV (reverse program) CN-channel1 started * ;M1=67 REV (Freifahrprogramm) NC-Kanal 1 beendet / Reset * ;M1=67 REV (reverse program) CN-channel1 finished I Reset * ;M1=70 主轴短暖机程序激活* ;M1=70 Spindle short warm-up cycle is active * ;M1=71 主轴短暖机程序循环完成 * ;M1=71 Spindle short warm-up cycle finished * ;M1=72 主轴长暖机程序激活** ;M1=72 Spindle long warm-up cycle is active * ;M1=73 主轴长暖机程序循环完成 * ;M1=73 Spindle long warm-up cycle finished * ;M1=74 主轴暖机程序被低温激活* ;M1=74 Spindle warm-up cycle of low temperature is active * ;M1=75 主轴暖机程序被低温激活后循环完成 * ;M1=75 Spindle warm-up cycle of low temperature finished * ;M1=76 机床暖机循环后关闭* ;M1=76 OPTION: Machine off from warm-up cycle * ;M1=77 开始时间监控器主轴使用10分钟 * ;M1=77 Start time monitoring spindle in use 10 minutes * ;M1=78 开始时间监控主轴使用15分钟 * ;M1=78 Start time monitoring spindle in use 15 minutes * ;M1=79 开始时间监控主轴使用60分钟 * ;M1=79 Start time monitoring spindle in use 60 minutes * ;M1=80 托盘交换请求* ;M1=80 Pallet change desired * ;M1=81 PCH 使能从暖机循环 * ;M1=81 PCH enable from warm-up cycle * ;M1=82 暖机循环中主轴倍率100%打开 ;M1=82 Spindle override 100% on from warm-up cycle * ;M1=83 暖机循环中主轴倍率100%关闭 ;M1=83 Spindle override 100% off from warm-up cycle * ;M1=84 暖机循环持续激活 ;M1=84 Warm-up cycle is still active * ;M1=85 开始时间监控主轴使用30分钟 * ;M1=85 Start time monitoring spindle in use 30 minutes * ;M1=86 启动主轴装卸刀循环使能* ;M1=86 Start enable cycle load I unload tool via spindle * ;M1=87 用主轴装刀激活* ;M1=87 Load tool active via spindle * ;M1=88 用主轴卸刀激活* ;M1=88 Unload tool active via spindle * ;M1=89 刀库旋转* ;M1=89 Rotate tool magazine * ;M1=90 刀库在位 * ;M1=90 Tool magazine in position * ;M1=91 Altplatz zur Wechselstelle positionieren * ;M1=91 Position old place to change position * ;M1=92 Startvoraussetzung fuer Werkzeugwechsel fehlt * ;M1=92 Start condition for tool change missing * ;M1=93 Spindel freigeben fuer Spindel referenzieren * ;M1=93 Spindle enable for referencing spindle * ;M1=98 Reserviert fuer Maschinendauerlauf mit autom. Werkstueck spannen * ;M1=98 Spare for machine continuous cycle with autom. part clamp * ;M1=99 Reserviert fuer Maschinendauerlauf mit Palettenwechsel * ;M1=99 Spare for machine continuous cycle with pallet change * ; ;M-Funktionen K2 XHC 241 SIN 840D ;============================================================= ; ;M64 请求启动监控器在通道2检查钻头 ;M64 OPTION: Request start enable cycles check drill CN-channel 2 * ;M65 在通道2检查钻头** ;M65 OPTION: Check drill CN-channel 2 * ;M66 Bohrer pruefen beendet NC-Kanal 2 * ;M66 OPTION: Check drill finished CN-channel 2 * ;M71 Rev-Progr. (Freifahrprogramm) NC-Kanal 2 begonnen * ;M71 Rev-progr. (reverse program) CN-channel 2 started * ;M72 Rev-Progr. (Freifahrprogramm) NC-Kanal 2 beendet * ;M72 Rev-progr. (reverse program) CN-channel 2 finished * ;M78 监控器在通道2检查钻头* ;M78 OPTION: Monitoring start check drill CN-channel 2 * ;M91 刀具卡爪关闭** ;M91 OPTION: Close tool gripper * ;M92 刀具卡爪打开** ;M92 OPTION: Open tool gripper *