Disassembly Procedure
V1.0
2 - 1
Disassembly Procedure
Please follow the information provided in this section to perform the complete
disassembly procedure of the notebook. Be sure to use proper tools described
before.
SUS K42 Series Notebook consists of various modules. This chapter describes the
procedures for the complete notebook disassembly. In addition, in between procedures, the
detailed disassembly procedure of individual modules will be provided for your service
needs.
The disassembly procedure consists of the following steps:
◆ Battery Module
◆ Memory Module
◆ HDD Module
◆ ODD Module
◆ Keyboard Module
◆ Wireless LAN Module
◆ Top Case Module
◆ LCD Module
◆ Motherboard Module
Chapter
2
A
Disassembly Procedure
V1.0
2 - 2
Battery Module
The illustration below shows how to remove the battery module.
Remove Battery Module
Open latch 1 and hold the latch 2 when take the battery away.
BACK
Memory Module
The illustration shows how to remove the Memory Module form the notebook.
Remove Memory Module
1. Remove 2 screws on the DIMM door. Remove the DIMM door.
B A T T E R Y
M E M O R Y
Disassembly Procedure
V1.0
2 - 3
2. Pull two latches here to pop the memories module up at 45 angles, and then pull out the
module at that angle.
BACK
HDD Module
The illustrations below show how to remove the HDD Module from the notebook.
Remove HDD Module
1. Remove 2 screws on HDD door. Lift up the HDD door and take it away.
H D D
Disassembly Procedure
V1.0
2 - 4
2. Remove 4 screws on the HDD module. Pull back the HDD module and lift it away.
2. Remove 4 screws to separate HDD from HDD housing
BACK
Disassembly Procedure
V1.0
2 - 5
ODD Module
The illustrations below show how to remove the ODD Module.
Remove ODD Module
1. Remove 2 screws on the bottom case and pull out the ODD module from the compartment.
BACK
Keyboard Module
The illustrations below show how to remove the Keyboard and disassemble the Keyboard Cover.
Remove the Keyboard
1. Open 4 latches (ESC, F5, F12 and Delete) on keyboard module by a pair of tweezers.
O D D
K E Y B O A R
Disassembly Procedure
V1.0
2 - 6
2. Turn over the keyboard plate and disconnect the keyboard FPC and remove the keyboard
plate.
Remove Keyboard Cable
1. Use a flexible connector tool to unlock the cable connector on both ends (no. 1).
2. Carefully pull out the keyboard cable (no. 2) with a pair of tweezers.
3. Lock the connector (no. 3) again to avoid possible breakage.
1. Unlock
2. Cable out
3.
Lock
1. Unlock
3.
Lock
Disassembly Procedure
V1.0
2 - 7
BACK
Wireless LAN Module
The illustration below shows how to remove the Wireless LAN Module from the notebook.
Remove Wireless LAN Module
Disconnect the antennas and remove 2 screws on Wireless LAN card and pull out the card from
its slot.
BACK
W L A N
Disassembly Procedure
V1.0
2 - 8
Top Case Module
The illustrations below show how to remove and disassemble the Top Case Module of the notebook.
Remove the Top Case Module
1. Remove dummy SD card from the system.
2. Remove 11 screws on the top case and disconnect the touchpad FPC. Turn over the device and
remove 14 screws on the bottom case. Then separate the bottom case from the top case and take the
top case away.
T O P C A S E
Disassembly Procedure
V1.0
2 - 9
Disassembly Procedure
V1.0
2 - 10
Disassemble the Top Case Module
3. Tear off the touchpad mylar on the top case. Disconnect the touchpad FPC and remove the FPC.
BACK
Disassembly Procedure
V1.0
2 - 11
LCD Module
The illustrations below show how to remove and disassemble the LCD Module.
Remove the LCD Module
1. Remove 6 screws securing the LCD module. Disconnect the LVDS cable and release the WLAN
antennas. Then lift up the LCD module and take it away.
L C D
Disassembly Procedure
V1.0
2 - 12
Disassemble the LCD Module
2. Remove 8 screws on the LCD bezel. Pry the edges of LCD bezel and remove the front bezel.
Disassembly Procedure
V1.0
2 - 13
3. Remove 12 screws securing the LCD panel. Disconnect the camera cable and release the
microphone. Then remove the LCD panel.
Disassembly Procedure
V1.0
2 - 14
4. Disconnect the LVDS cable and remove the cable.
Disassembly Procedure
V1.0
2 - 15
5. Remove 8 screws on LCD brackets and separate the 2 brackets.
BACK
Disassembly Procedure
V1.0
2 - 16
Motherboard Module
The illustrations below show how to disassemble and remove the Motherboard Module.
Remove the Motherboard Module
1. Remove 2 screws on the motherboard. Disconnect the Bluetooth cable and the speaker cable.
Remove the motherboard from the bottom case.
M O T H E R B O A R D
Disassembly Procedure
V1.0
2 - 17
Disassemble the Motherboard Module
2. Remove 6 screws on the thermal solution. Disconnect the fan cable. Remove the thermal.
3. Turn the non-removable screw here 180 degrees counter-clockwise to loosen the CPU.
Squeeze the vacuum handling pump on the CPU and use it to lift the CPU away.
Disassembly Procedure
V1.0
2 - 18
4. Remove the IO board from the bottom case.
5. Remove 4 screws on the speaker. Disassemble the speaker from the bottom case.
BACK
Battery Module
Remove Battery Module
Memory Module
Remove Memory Module
battery
Memory
HDD Module
Remove HDD Module
HDD
ODD Module
Remove ODD Module
Keyboard Module
Remove the Keyboard
odd
Keyboar
Wireless LAN Module
Remove Wireless LAN Module
WLAN
Top Case Module
Remove the Top Case Module
Disassemble the Top Case Module
Top case
LCD Module
Remove the LCD Module
Disassemble the LCD Module
lcd
Motherboard Module
Remove the Motherboard Module
Disassemble the Motherboard Module
Motherboard
本文档为【K42_Series_Chapter_02-v1.0】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑,
图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。