电火锅外观检验标准

电火锅外观检验标准 一、 说明 本标准适用于顺德格力小家电有限公司所生产的电火锅外观 检测 工程第三方检测合同工程防雷检测合同植筋拉拔检测方案传感器技术课后答案检测机构通用要求培训 判定标准。 二、 检查方法及条件 1( 光源充足; 2( 检查人员校正视力必须具备在0.8以上; 3( 检查方法采用目视检测，测试距离为30?。 三、 检查标准 1( 印花钢板: 序号 检验内容 合格限度判定标准 1 杂色、黑点 正面?,1.0?，非正面?,1.5?的杂色、黑点允许2个;?,0.5?呈分散状允许数量不超过10 个，?,0.3?呈分散状分布允许存在。 2 涂膜凹陷 可见坯料:不合格;看不见坯料:直径小于,3.0?不超过3个 3 纤维丝 不允许有头发;正面部位:长度小于50?允许1条;其他部位:长度小于80?允许存在1条。 4 击痕(凸点) 不明显的击痕允许存在。 5 划伤 反光才可看见的划痕不要求;可见基材的划伤不允许，但长度小于15?，宽度小于0.25?的伤痕 可用颜色一致的漆补上。 defense work, fully meet annual targets. Foreign Affairs strengthened immigration and passport, file management, the implementation of the Office system, promote standardization and institutionalization of the management of Foreign Affairs. Overseas Chinese, based on policy advocacy and for "overseas Chinese" servicesregistration system on duty, troubleshooting safety and maintain social stability. Comprehensive control of public security and was affirmed by the community. 4, further strengthening of foreign and overseas Chinese Affairs, local records ' compilation and civil air 2( 玻璃盖 序号 检验内容 合格限度判定标准 1 击痕 不允许存在击痕; 2 气泡 允许?,1.5?气泡2个呈分散存在距离大于4?，宽度小于0.3?，长度小于5?条状气泡存在2条呈分散状距离4? 3 杂色、黑点 不允许明显的杂色、黑点存在; 4 划伤 允许宽度?,0.1?的轻微划伤存在2条，长度不大于20?，要求呈分散状分布; 5 爆边 中心孔允许2?宽度的爆边存在，其他位置不允许。 3( 塑料件 (1) 外壳 序号 检验内容 合格限度判定标准 正面:?,1.0?的浅色点或?,0.5?的深色点允许3处;其他部位:?,1.0?的浅色点或?,0.5?的深色点允1 黑点、杂色 许5处;长度?10?，宽度小于0.3?的浅色杂色条纹允许2条呈分散状; 2 收缩痕 可允许有轻微的收缩痕(见极限样本); 3 水纹 可允许有轻微的水纹或熔接痕(见极限样本); 4 填充不足 表 关于同志近三年现实表现材料材料类招标技术评分表图表与交易pdf视力表打印pdf用图表说话 pdf 面不允许存在填充不足，非可见部位不影响装配的允许存在轻微填充不足。 5 擦花 反光才能看见的线条擦痕不考虑;片状面积小于250M?的擦花允许2处。 6 气泡 小于,0.6?的分散气泡允许存在，允许存小于,1.2?凹陷较浅的气泡不超过5个。 defense work, fully meet annual targets. Foreign Affairs strengthened immigration and passport, file management, the implementation of the Office system, promote standardization and institutionalization of the management of Foreign Affairs. Overseas Chinese, based on policy advocacy and for "overseas Chinese" servicesregistration system on duty, troubleshooting safety and maintain social stability. Comprehensive control of public security and was affirmed by the community. 4, further strengthening of foreign and overseas Chinese Affairs, local records ' compilation and civil air 7 飞边 宽度0.5?，长度小于50?的气边允许存在1处; (2) 底座 序号 检验内容 合格限度判定标准 ?,1.6?的浅色点或?,0.8?的深色点允许3处;长度?10?，宽度小于0.5?的浅色杂色条纹允许2条呈分散状; 1 黑点、杂色 2 水纹、熔接痕 可允许有轻微的收缩痕(见极限样本); 3 擦花 反光才能看见的线条擦痕不考虑;片状面积小于250M?的擦花允许2处。 4 填充不足 表面不允许存在填充不足，非可见部位不影响装配的允许存在轻微填充不足。 5 气泡 小于,0.6?的分散气泡允许存在，允许存小于,1.2?凹陷较浅的气泡不超过5个。 6 飞边 明显飞边不允许存在; 注:底座下表面外观不要求。 4( 五金件 (1)外锅(镀铝钢板) 序号 检验内容 合格限度判定标准 1 击痕变形 允许直径?,10?的变形1处(但须对装配无影响); 2 黑斑 侧面允许直径?,5?的5点呈分散状分布，淡色油斑不要求; defense work, fully meet annual targets. Foreign Affairs strengthened immigration and passport, file management, the implementation of the Office system, promote standardization and institutionalization of the management of Foreign Affairs. Overseas Chinese, based on policy advocacy and for "overseas Chinese" servicesregistration system on duty, troubleshooting safety and maintain social stability. Comprehensive control of public security and was affirmed by the community. 4, further strengthening of foreign and overseas Chinese Affairs, local records ' compilation and civil air 3 黑色条纹 允许色泽较浅宽度?5?长度?100?三条; 4 划痕 长度?100?的轻微划痕允许存在2条呈分散状; 5 镀层脱落 ?,1.5?的小点允许存在3点; 注:装配后不可见的外观不良不考虑。 (1)外锅(喷粉) 序号 检验内容 合格限度判定标准 1 击痕变形 允许直径?,10?的变形1处(但须对装配无影响); 浅色杂点允许直径?,3?的5点呈分散状分布，深色或黑色杂点允许直径?,2?的5点呈分散状分布，条纹状杂色2 杂色、黑点 允许色泽较浅宽度?1?长度?20?三条; 3 凸点 允许直径?2?的凸点3点呈分散状分布; 4 划痕 可见基材的划伤不允许，但长度小于20?，宽度小于0.5?的划痕可用颜色一致的漆补上; (3)内锅 序号 检验内容 合格限度判定标准 1 划伤 外表面允许宽度?,0.1?,长度?30?的划伤3条;内表面卷边处允许长度小于20?的划伤1条,但不能 露出基材;内表面侧面允许小于5?的划伤1条但不能露出基材; 2 杂色 卷边处面积?700m?的杂色斑允许存在2处，杂色与涂层颜色接近; 3 凸点 底部允许有?,1.0?的圆滑凸点3处，侧面允许?,1.5?的圆滑凸点3处(尖锐凸点不允许存在); defense work, fully meet annual targets. Foreign Affairs strengthened immigration and passport, file management, the implementation of the Office system, promote standardization and institutionalization of the management of Foreign Affairs. Overseas Chinese, based on policy advocacy and for "overseas Chinese" servicesregistration system on duty, troubleshooting safety and maintain social stability. Comprehensive control of public security and was affirmed by the community. 4, further strengthening of foreign and overseas Chinese Affairs, local records ' compilation and civil air 4 晶斑 不要求; 5 材料痕 无明显发黑的材料痕允许存在; 6 压痕 直径?,3?的压痕允许不超过3个(压痕为材料本身原因); 7 碰瘪 直径?,5?的轻微碰瘪允许1处(不能在底面); 8 油斑 色泽较浅的油斑不要求，直径?,3?的油斑允许存在3点呈分散分布; 5、控制面板 序号 检验内容 合格限度判定标准 1 划伤 轻微指甲痕在边缘位置允许1处，反光可见的轻微划伤允许存在，划伤不得产生对控制面板商标及字体上。 2 黑点 ?,0.8?的黑点允许存在分散3点，?,1.0?的黑点允许存在1点。 3 杂色 ?,2?的杂色点允许存在1处。 4 飞边 面板边缘不允许飞边。 6、成品间隙 产品系列名称 各部位间隙标准 RF-P150Y(时尚电火锅) 外壳—控制盒:?1.0?;外壳—底座:?,0.7?;底座—控制盒:?,0.8?; RF-P130Y/B(时尚电火锅) 外壳—控制盒:?0.5?;外壳—底座:?,0.7?;底座—底座盖板:?,1.0?; defense work, fully meet annual targets. Foreign Affairs strengthened immigration and passport, file management, the implementation of the Office system, promote standardization and institutionalization of the management of Foreign Affairs. Overseas Chinese, based on policy advocacy and for "overseas Chinese" servicesregistration system on duty, troubleshooting safety and maintain social stability. Comprehensive control of public security and was affirmed by the community. 4, further strengthening of foreign and overseas Chinese Affairs, local records ' compilation and civil air RF-P150S(时尚电火锅) 外壳—底座:?,0.7?; defense work, fully meet annual targets. Foreign Affairs strengthened immigration and passport, file management, the implementation of the Office system, promote standardization and institutionalization of the management of Foreign Affairs. Overseas Chinese, based on policy advocacy and for "overseas Chinese" servicesregistration system on duty, troubleshooting safety and maintain social stability. Comprehensive control of public security and was affirmed by the community. 4, further strengthening of foreign and overseas Chinese Affairs, local records ' compilation and civil air