公制螺纹接头内径与软管内径对照表

公制螺纹接头内径与软管内径对照表 公制螺纹接头内径与软管内径对照表 Comparison table for inside diameter, connector with metric threads to inside diameter, conduits 公制螺纹管接头 软管CONDUIT CONNECTOR WITH METRIC THREAD 标称内径 nominal 内径 Inside diameter width mm (nom.) ID 内径 螺纹规格 NW Inside ø nominal Thread size 标准 excel标准偏差excel标准偏差函数exl标准差函数国标检验抽样标准表免费下载红头文件格式标准下载 金属螺纹 聚酰胺螺纹公制metric standard metal thread polyamide thread - 07 10 6.2 M10 - 5.7 10 12 9.6 M12 8.0 - 10 12 9.6 M16 11.0 9.7 12 16 12.0 M16 11.0 13.7 17 20 16.2 M20 14.6 18.6 23 25 22.6 M25 19.0 25.7 29 32 29.0 M32 26.0 33.4 36 40 36.5 M40 32.0 42.7 48 50 47.5 M50 42.0 54.0 48 50 47.5 M63 53.0 PG 螺纹接头内径与软管内径对照表 Comparison table for inside diameter, connector with PG threads to inside diameter, conduits PG制螺纹管接头 软管CONDUIT CONNECTOR WITH PG THREAD 标称内径nominal width 内径 Inside diameter mm (nom.) ID NW 内径 螺纹规格 Inside ø nominal Thread size 金属螺纹metal 标准 聚酰胺螺纹公制metric thread standard polyamide thread - 07 10 6.2 PG07 8.0 9.5 10 12 9.6 PG09 10.0 12.5 12 16 12.0 PG11 13.0 14.5 - - - PG13.5 14.5 16.5 17 20 16.2 PG16 17.5 22.5 23 25 22.6 PG21 22.5 30.5 29 32 29.0 PG29 30.5 40.5 36 40 36.5 PG36 37.5 - - - - PG42 48.0 52.0 48 50 47.5 PG48 50.0 适用于PMA接头扭矩 Torques for PMA connector PMA 接头螺纹推荐扭矩 / Recommended torques for the PMA connector thread 对带螺纹孔的开口 / For threaded bore holes 带螺母 / With lock nuts * 螺纹组合:金属，金属 / Thread combination: metal + metal ** 螺纹组合:金属，聚酰胺或聚酰胺，聚酰胺 / Thread combination: metal + polyamide or polyamide + polyamide 注意:以上数据为近似值。在实际应用中请考虑螺纹的影响。The dates are approximate values. At application please take into account the influence of the counter-thread. 接头带消除应力设计 / Connector to achieve strain relief 当设计和指定安装两个连接点时，以下尺寸应要计算在内。 在每个管接头内的插入长度要额外计算，请参照下表。 The following dimensions have to be taken into account if designing and specifying a certain length between two connecting points. The push-in length have to be additionally considered for each connector as mentioned below. 如不正确安装，将不能达到指定IP 防水防尘等级。 Straight cut with PMA Cutting tool 使用PMACUT 剪切工具剪切软1. PMACUT, 90o to the conduit axis. 管，剪切面与软管轴心垂直。 The retaining clip is pre-mounted. 管卡已预先安装，推入时轻微转Push in with a slight twist until the 2. 动直至不能推入为止。 stop. Pull back slightly to ensure the 3. 轻微回拉软管，确保锁紧。 locking mechanism is fully engaged. Recommendation for applications under vibrations or similar: 在振动或相似情况下的应用建 Protect threads with commercial 4. 议:为保护螺纹最好使用密封胶 adhesive or seal compound (e.g. 或黏合剂。(如:Loctite) Loctite). Do not bend off the PMAFLEX 安装管接头的软管部分不要弯conduit directly after the connector. If 5. 曲，如果定位请使用管夹或其他necessary destine the direction with 支撑。 a system support or similar. For safety reasons: To re-open a 为安全起见: 需用螺丝刀才能6. screwdriver has to be used. 开启管夹。 使用PMACUT 剪切工具剪切软 管，剪切面与软管轴心垂直。 Straight cut with PMA Cutting tool 1. PMACUT, 90o to the conduit axis. Conduit – Seal Cap – Connector - 软管,密封套,管接头管夹,O 2. Oval Clip – Flat Gasket or O-ring 型环或垫圈 Push seal cap onto end of conduit to achieve an ingress protection up to 将密封套安装于软管末端， 根 IP68 according to IEC 529 / EN 3. 据IEC529/EN60529 标准， 防 60529. 护等级可达IP68 。 For ease of installation moisten seal 为安装方便， 密封套可使用水4. cap with water or lubricant. 或润滑剂来润滑。 Push conduit with seal cap with slight twist fully into connector. (For 将带密封套的软管完全推进接 safety reasons, retaining clip will not fit if 5. 头。(如果密封套没有完全安装 seal cap is not fully installed.) 好，管卡将不能安装) Push in the Retaining Oval Clip until the barbed hooks are optimal set. 推进管卡直至完全配合。(确保(Ensure that the opening slot of the retaining 6. 管卡缺口部位在软管侧) clip is on conduit side) Recommendation for applications under vibrations or similar: 在振动或相似情况下的应用建 Protect threads with commercial 7. 议:为保护螺纹最好使用密封胶 adhesive or seal compound (e.g. 或黏合剂。(如:Loctite) Loctite). Do not bend off the PMAFLEX conduit directly after the fitting. If 安装接头的软管部分不要弯曲， necessary destine the direction with 8. 如果定位请使用管夹或其他支 a system support or similar. 撑。 For safety reasons: To re-open a 为安全起见: 需用螺丝刀才能9. screwdriver has to be used. 开启管夹。