航海英语 (22)

Unit 22 Ship’ Equipment TEXT 1 Hatch Covers When hatch covers or pontoons are stowed on the weather deck abreast of hatches, they shall be arranged in stable not closer to the hatch coaming than 0.91m.Exception:On the working side of the hatch, hatch covers or pontoons may be spread one high between the coaming and bulwark with no space between them, provided the height of the hatch coamming is no less than 0.61m .Under no circumstances shall hatch covers or pontoons be stacked higher than the hatch coaming or bulwark on the working side of the hatch. 22单元船舶设备 文本 1舱盖 当舱口盖板或方形盖板堆叠在露天甲板上且与舱口并列时,它们应稳定绑扎离舱口围板不接近0.91m. 除非: 在舱口工作一侧,当舱口盖或方形盖板舱口围板和舷墙之间并排没有空间时,则高于舱口围板的高度不少于0.61m。在舱口边工作时,任何情况下都不允许舱口盖的堆放高于堡垒舱口围或舷墙。 On seagoing vessels, hatch boards or similar covers removed from the hatch beams in a section of partially opened hatch during cargo handling, cleaning or other operations shall not be stowed on the boards or covers left in place within that section. 在海上航行船舶上、当打开舱口在货物装卸、清洗或其他作业时,舱口盖板或类似的覆盖物被移开舱口盖梁段部分不应放在未被打开的部分上。 Hatch beams shall be laid on their sides, or stood on edge close together and lashed .Exception: The latter paragraph shall not apply in cases where hatch beams are of such design that: 舱口活动梁应该放在它们的位置上,或保持边缘紧密绑扎相靠。.除非:进一步作业不宜适用,那样的舱口活动梁 设计 领导形象设计圆作业设计ao工艺污水处理厂设计附属工程施工组织设计清扫机器人结构设计 : The width of the flange is 50 percent or more of the height of the web; 折边的宽度50%及以上的高度的强肋骨; and The flange rests flat on the deck when the hatch beam is stood upright. 当舱口活动梁直立着折边平摊在甲板上时。 Strongbacks, hatch covers, and pontoons removed from hatch openings and placed on the weather deck shall not obstruct clear fore-and-aft or coaming-to-bulwark passageways and shall be lashed or otherwise secured to prevent accidental dislodgement. Dunnage or other suitable material shall be used under and between tiers of strongbacks and pontoons to prevent them from sliding when stowed on steel decks. 强力盖板,舱盖,方形舱盖从舱盖口移开放置在露天甲板上不得阻碍清晰的首尾线舱口围板到舷墙的长廊,并且绑扎或固定以防止意外的脱出。当装在钢质甲板时,货垫或其它合适的 材料 关于××同志的政审材料调查表环保先进个人材料国家普通话测试材料农民专业合作社注销四查四问剖析材料 应该是在强力盖板下层和方形舱盖之间以及防止滑动。 Hatch covers unshipped in an intermediate deck shall be placed at least 0.91m from the coaming or they shall be removed to another deck. Strongbacks unshipped in an intermediate deck shall not be placed closer than 15.24cm from the coaming and, if placed closed than 0.91m,shall be secured so that they cannot be tipped or dragged into a lower compartment . If such placement or securement is not possible, strongbacks shall be removed to another deck. 未安装舱盖板的地方应把它放在至少离舱口围板0.91m,它们要移到另一层甲板上。未安装强力盖板的地方应把它放在距离舱口围板不小于15.24cm,如果靠近小于0.91m,则使他们不能绑牢或不能斜出拖入下一层甲板。如果这样的放置或系固是不可能的, 强力盖板应移到另一层甲板上 Any hatch beam or pontoon left in place next to an open hatch section being worked shall be locked or otherwise secured ,so that it cannot be accidentally displaced .All portable, manually handled hatch covers ,including those bound together to make a larger cover ,shall be removed from any working section ,and adjacent sections , unless securely lashed . 在靠近正在工作中的舱口,任何舱口横梁或方形盖板均应锁住或将其系固,,以便使他不能发生意外移动。所有轻便的,可手工操作的舱口遮盖物,包括这些有较大遮盖物的区域,均应移离任何工作中的区域和临近的区域,除非已将其扎牢。 The roller hatch beam at the edge of the open section of the hatch shall be lashed or pinned back so that it cannot be moved toward the open section. 舱口开口区边缘的滚动舱口横梁,应将其扎牢或将其压住,以便使它不能移向开口区域。 Rolling, sectional or telescopic hatch covers of barges which open in a fore and aft direction shall be secured against unintentional movement while in the open position. 驳船上,在船首和船尾方向开着的滚动式、拼接式或套叠式舱盖均应系牢,以避免在开启位置发生意外的移动。 Hinged or folding hatch covers normally stowed in an approximately vertical position shall be positively secured when in the upright position, unless the design of the system otherwise prevents unintentional movement. 铰链式或折叠式舱盖一般装置近似垂直安全的位置,防止垂直时发生意外,除非系统要求,否则避免意外移动。 Hatches shall not be opened or closed while employees are in the square of the hatch below. 当船员在舱内作业时,舱口不得关闭,有船员在舱口下时,也不要开启。 All materials such as dunnage lashings, twist locks, or stacking cones shall be removed from the hatch cover or be secured to prevent them from falling off the cover before the hatch cover is moved. 所有的材料,如货垫,捆绑,旋锁,不应放在舱口盖上或覆盖在舱口盖摇动,固定阻止他们掉下来的 When a hatch is to be covered ,hatch covers or night tents shall be used . Any covering that only partially covers the hatch ,such as alternate hatch covers or strips of dunnage ,shall not be covered by a tarpaulin .Exception : A tarpaulin may be used to cover an open or partially open hatch to reduce dust emissions during bulk cargo loading operations ,if positive means are taken to prevent employees from walking on the tarpaulin . 当舱口将被盖住时,舱口盖或夜晚的帐篷应被使用,任何遮蔽物部分的遮蔽舱口,例如交替舱口盖或搬走支撑板,将不会被防水布覆盖。除外,防水布可用来覆盖开着或部分开的 舱口以减少在货物装卸过程中汽油的挥发,如果可能的话,采用积极的手段来阻止从业人员在油布上行走。 Ⅱ ventilation 通风 1. Introduction介绍 Shipboard ventilation systems supply and remove air to/from spaces throughout the ship. In doing so ,these systems control quality of breathing air and protect personnel and sensitive cargoes from potentially hazardous airborne contaminants, fires, explosions, and excessive heat. Theability of ventilation systems to protect personnel from these hazards is particularly important aboard ships, shich are like floating cities fitted into a very limited apsce.Well designed and easily maintained ventilation systems are critical to a safe and comfortable shipboard work environment. 装货通风系统为整艘船舶提供并注入空气。当启动那些系统的时候,那些系统提供大量的新鲜空气,从一些潜在的经过空气传播的污染物,比如火灾,爆炸和过多的热流中,保护全体船员和敏感货物。通风系统在船上从危险中保护船上全体成员的能力是非常重要的。这个就像一个漂浮的城市忽然间被装进一个非常狭窄的空间里一样。好的设计和简单的维护通风系统决定了装货工作环境的安全和舒适程度。 Ventilation systems include a supply, or makeup air system and an exhaust system. Supply systems replace contaminated air exhausted from a workspace with uncontaminated outside air. Supply ventilations systems also provide replenishment air to air conditioning recirculation systems. Exhaust systems remove odors, heated air, and airborne contaminants from the workspace. Both supple and exhaust airflow quantities must be balanced. 通风系统包括供给或者接通空气系统和为被污染的空气。供给系统从一个未被污染物污染的空气的场所,取代污染空气的排放。供给通风系统支持补充空气给空调循环系统,排气系统能消除工作场所异味,排除热空气,排除污染物。供给和排放对空气流动的工程量必须平衡。 All components of ventilation systems such an fans, motors, ducts, dampers, air intakes and outlets, filters, and access panels, must work properly in order for the systems to operate safely and efficiently, Therefore, ventilation system design must be considered an essential part of planning, development, and production of new shipboard equipment and systems and the facilities needed for their support. Not only must the systems themselves operate properly, but the way in which the operator and maintained fit into the design, or human systems integration, must also be taken into account. Failure to provide effective ventilation systems in the design stag can create costly obstacles to safe and efficient ship operation and maintenance, which ultimately presents a threat to personnel safety and health. 为了是系统安全和有效的工作,所有的通风系统的部件,例如风扇,马达,管道,气阀,空气吸入和排除,过滤器检修门都应该前挡工作,因此,通风系统的设计必须被看作是 计划 项目进度计划表范例计划下载计划下载计划下载课程教学计划下载 ,发展,新船舷设备制作以及系统和需要他们支持的设施的必须的一部分。不仅系统自身的恰当操作,并且适合设计的操纵和维持的方式以及人工系统整合,都应该是考虑的因素,在设计阶段未能成功提供有效的通风系统,会对安全和有效的船舶操纵和维护产生高昂障碍代价,因此对个人安全和健康呈现威胁。 2. Ventalation design and maintenance problems in laundries and galleys Aboard ships, a great deal of actively involving complex equipment makes place in a relatively small space using large amounts of energy, A by-product of energy is heat. The most widespread ventilation problem aboard ship is controlling heat humidity produced by the cleaning and cooking processes in laundries and galleys. the build-up dirt, grease, and oil in the ducts serving these spaces, will restrict airflow and reduce exhaust and supply air flow capabilities. Restricted air exhaust and supply will result in elevated temperatures, High heat and humidity lead to heat stress conditions that are both uncomfortable and reduce personnel productivity. In extreme cases, uncontrolled heat stress will expose personnel to the possibility of heat-related illnesses like heat exhaustion and heat stroke. Under certain conditions, personnel must be allowed time in a cooler environment to recover physiologically from the effects of heat stress. This has an indirect, but potentially very significant effect on cost over the life of the ship, because of reduced productivity and the need for additional manpower to perform a given set of tasks. 登船时大量关于复杂设备的活动发生在相对较小的空间,这些活动要消耗大量能量。发热是能量消耗的副作用,在船上通风产生最普遍的问题是控制由在洗衣房和厨房进行的清洁和烹饪产生的热量和湿度。在接触上述地方的甲板上,逐渐增加的污垢,油脂和油,将会限制空气流动,减少废弃排除和供空气流通的能力。高温和高湿度所导致的热压力状况,使人感到不舒服并降低个人的劳动效率。在极度事件中,未得到控制的热压力将使人暴露在可能与热量相关的疾病下,如:中暑衰竭。在通常情况下,一个人为了从热压力影响下恢复生理作用,必须允许有足够的呆在阴凉环境下的时间。这对于船舶的寿命有间接的作用,但却是潜在的并对花费具有重要影响,因为这降低了劳动生产率和为了完成给定任务所需要的额外劳动力。 Another common ventilation problem associated with shipboard laundries and galleys is that airborne materials can collect in ducts unless a good pre-filtration system is available and effectively maintained. Large volumes of lint generated in laundries can partially obstruct airflow and serve as potential combustion sources. Grease and other cooking residues generated in galleys that collect in ducts can also become combustible, Ventilation duct fires are extremely difficult to extinguish. 另一个几点相关的通风问题是除非有一个很好的可利用的且直接有效的过滤系统,船上洗衣房和厨房经空气传播的物质才可以收集到管理里。洗衣房里大容积的麻布由于部分地被阻隔了空气流通会成为潜在的燃烧源头。厨房里被收集到的管道的油脂和另外一些剩下的食物也有可能成为燃烧物,通风管道里的火灾非常难以扑灭。 3. Ventilation and maintenance problems in hazardous material storerooms and workshops Poorly maintained shipboard ventilation systems will result in dirty aid-filters that exceed design pressure drops, clogged ductwork, and low airflow. This can be particularly dangerous in shipboard hazardous material storerooms and in workshops that use hazardous materials. Inadequate ventilation can result in build-up of potentially hazardous levels of contaminants such as paint solvents. In extreme cases, control below fire-safety levels may be jeopardized, particularly after a hazardous material spill. 保养不善的船上通风系统将导致脏的空气过滤(超过设计的眼里落尘,阻塞管道,和低的空气通过量)。在船上物料间或在工作间使用危险物料将尤为危险,不恰当的通风系统将导致增加潜在污染物危险水平,例如油漆,在极端条件下,防火安全控制将危急,尤其危险材料溢出时。 4.Ventilation component maintenance & status monitoring problems 通风装置的维护及状况监测的问题 Shipboard ventilation components are a particular challenge to maintain and monitor because: 船上通风装置的维护与监测是一项特殊的挑战,因为: Ventilation components aboard ship suffer from the entry of salt-water spray, and re-entry of exhaust soot into supply air intakes resulting in internal corrosion to ductwork, and deterioration of air handling equipment. 船上通风装置会成为喷雾状海水的入口,同时排除带黑烟的气体也进入空气通风口,导致管道系统内部的侵蚀,空气控制设备变坏。 Most ventilation components are located in constrained spaces, making maintenance and repairs difficult. 大部分通风设备位于狭窄的空间里,使维护和修理起来困难。 Maintenance costs are high where the current maintenance strategy is based exclusively on either periodic efforts or component failures. This strategy results in regular disruption of service to sailors. 维护费用高是由于现在的维护的 方法 快递客服问题件处理详细方法山木方法pdf计算方法pdf华与华方法下载八字理论方法下载 是基于周期的维护和装置故障的维护,这种方法导致水手的维护工作被规律的分散开。 Awkward location and poor labeling of monitoring equipment can complicate maintenance of ventilation systems and increase expenses over the life cycle of a ship. 由于笨重货物的摆放以及监测设备标签的缺损,使得通风系统的维护更加复杂,同时在船舶的寿命周期中花费增加。 5.Ventilation system are often a significant source of shipboard noise, Because of space constraints, air ducts used aboard ships are often very small and have sharp curves and bends. This results in air, moving through the ducts at very high velocities. Air moving at high velocities can be the cause of noise and vibration in the ventilation system. Fans can also project noise throughout the ventilation system if they are poorly mounted, not properly isolated from air ducts, and/or are the wrong size. Finally, noise, may be generated at the air duct outlets that distribute air in work environment if proper design parameters are not followed. Noise can be disturbing to personnel concentration levels, which could result in lost productivity. High noise levels may also present the risk of hearing loss to personnel in affected work spaces. 通风系统是船舶噪音重要来源,因为空间受限,船上空气管道一般很小且有大的曲线和弯曲。这导致空气在管道中高速流动。高速流动的空气是造成通风系统噪音和颤动的原因。当风扇安装不善,没恰当的与空气管道分离,同时,或者尺寸不对时,它将突出噪音。最终,如果恰当的设计部件没有被执行,噪音将发生在空气管道出口影响空气工作环境。噪音能影响个人的注意力水平,可能导致丧失生产力。在受影响的工作空间,高分贝的噪音将导致个 人的失聪明。 Ⅲ Cargo tank venting sy stems shall be independent of the ventilation arrangements for any other compartments. The arrangement and position of the openings in the cargo tank deck from which the emission of flammable vapours can occur shall be such an to minimize the possibility of flammable vapours being admitted into enclosed spaces containing a source of ignition or collecting in the vicinity of machinery and equipments which may constitute an ignition hazard. 油舱通风系统是独立于其他通风安排的部分,液货舱甲板上空间的安排和位置分布应使 散发的易燃蒸汽应该尽可能减到最小,易燃蒸汽必须无可否认的要装在一个密闭的空间里, 这些可能着火的来源或者在邻近的机器设备都可能构成燃烧起来的危险。 The cargo tank venting arrangements shall— 货物货舱通风安排将- Be so designed and constructed as to ensure that the pressure, above or below that of the atmosphere, within the tanks does not exceed the design pressures, 那么设计和建设,保障压力,高于或低于货舱内的大气压,不超过设计压力, Include pressure-vacuum valves capable of providing for the flow of vapour, air or inert gas mixtures caused by thermal variations within the cargo tank, and 包括真空-压力阀门的流量提供多方位的蒸汽、空中、水上或惰性气体混合物引起了热 力变化货舱,和货物,和 Be capable of providing for the flow of vapour, air or inert gas mixtures whilst the tank is being loaded, ballasted or discharged at the highest rate. 有能力的流量提供蒸汽、空中、水上或惰性气体混合物而货舱正在装货,压载或卸货, 利率最高。 Every vent system outlet to atmosphere from a valve shall be located an high and at the furthest distance from a source of ignition as is practicable and in no case shall it be located less than 2 metres above the cargo tank deck or less than 5 metres from air intakes or openings to enclosed spaces containing a source of ignition or from machinery and equipment which may constitute an ignition hazard. 每个排放系统从阀门口到大气中应该有高于且尽量远离火源是可行的,在任何情况下, 它不得在液货舱物甲板之上小于2m,或离进气孔或缺口含封闭空间点火源或离可能构成点 火的危害的机械和设备少于5m。 By-pass arrangements for the pressure-vacuum vales may be fitted if the vales are located in a vent main or masthead riser. Indicators showing whether the by-pass is open or shut shall be provided. 当阀门安在通风柱或桅顶竖板时,旁路应安排安装空气真空压力阀。隔水管指标显示将 提供旁通阀是否已被打开或关闭。 Every vent system outlet to atmosphere provided in accordance with subregulation shall: 每个排放系统提供出口到大气中,应与 规则 编码规则下载淘宝规则下载天猫规则下载麻将竞赛规则pdf麻将竞赛规则pdf 一致应该: Permit the free flow of vapour mixtures or be so designed that the discharge velocity of the vapour mixtures is at lease 30 metres per second; 设计允许自由蒸汽混合物流量或蒸汽混合排出速度至少30米每秒 Be so arranged that the vapour mixture is discharged vertically upwards; 安排混合蒸汽能垂直地向上排放。 Where the system permits the free flow of vapour mixtures be such that the outlets to atmosphere are located at least 6 metres above the cargo tank(If a fore and aft gangway is provided the outlets from the tanks shall be located at least 6 metres above the gangway if any outlet is less than 4 metres, measured horizontally, from the gangway or is less than 10 metres, measured horizontally, from the nearest air intake or opening to an enclosed space containing a source of ignition and from machinery and equipment which may constitute an ignition hazard); 在对出口到大气的系统允许的自由流动蒸汽混合物 ,须安装至少高于液货舱甲板6m。(如果在船头和船尾过道油箱开口须至少在过道6m以上处,当任何一开口水平测量距离过道应小于4m,或水平测量当离最近空气进口或来自机器或能造成点火危险的装备的火源围起的空间时,应小于10m); Where the system is so designed that the discharge velocity of vapour mixtures is at least 30metres per second, be such that the outlets to atmosphere are located at least 2 metres above the cargo tank deck and at least 10metres, measured horizontally, from the nearest air intake or opening to an enclosed space containing a source of ignition and from machinery and equipment which may constitute an ignition hazard; and 系统被设计能排出混合水汽的速度至少30m/s,这样对突出开口至少应在液货甲板以上2m,或水平测量离最近的空气进口,或火源围起的空间来自机器或能造成点火危险的装备至少10m。 Be so arrange as to prevent the design pressure of any cargo tank exceeded. 如此安排,防止任何货物货舱超过设计压力。 The venting arrangement of each cargo tank may be independent or combine with other cargo tanks and may be connected to the inert gas piping. Where the arrangements are combined with other cargo tanks, stop valves or other effective means of isolating each cargo tank shall be provided, Stop valves shall be provided with locking arrangements to permit control of their operation. Any cargo tank isolation arrangement provided in accordance with this subregulation shall not prevent the flow of vapour, air or inert gas caused by thermal variations within the tank. 由每批油舱独立或结合其他货舱, 在安排其他货舱结合时可以连接惰性气体管道,在安排与其他油舱相连时,应有截止阀或其他有效方法来允许它们的操作控制。任何油舱隔离安排应与规定一致,不应妨碍在油舱里流动的空气或蒸汽的惰性气体的热种群变化。 The venting system shall be provided with devices to prevent the passage of flame into the cargo tanks. The design, construction, location and testing of these devices shall be in accordance with relevant regulations. The devices for cargo tanks in which the atmosephere is flammable shall be flame arresters or high velocity vents. 排气系统应提供设备用于阻止通道内火焰进入油箱。这些设备的设计、建造、位置和测试都应当依照有关规定,有应当阻火器或能高流速排气。 The vents shall be connected to the top of each cargo tank and be self-draining to the cargo tanks when the ship is upright, trimmed up to 10 degrees by the stern and when inclined at any angle of list up to and including 15 degrees either way. Other permanently installed drainage arrangements may be permitted where it is not possible to provide self-draining vent lines. 通风空应在每一油箱顶部修整了10度尾倾,或任意角度倾斜15度情况之一时能自排水。在不能提供排气线的地方应安装永久排水系统。 High level alarms or overflow control systems or other ecquivalent means together with cargo tank content gauges and filling procedures shall be protec the tanks from excess pressure due to overfilling. 高位警报器或溢出控制系统意味着油舱容量计量和灌装程序盈满足保护油舱防止由于过度填充的过度压力。 Isolation of the slop tanks containing oil or oil residue in combination carriers from other cargo tanks shall be by blank flanges which shall remain in position at all tomes when cargoes other than oil cargoes are carried. 当不是油舱货物被装运时,单独的污水箱包括油和来自其他油舱运载物的污油,应通过一直保持了位置的空白边缘搬运。 The master shall be provided with information regarding the maximum permissible loading rate for each cargo tank and, in the case of each combined venting systems, for each group of cargo tanks. 在考虑通风系统和每批油舱货物的情况下, 船长应当提供关于每一油舱估计最大装载量信息。