proe精简技巧（proe精简技巧）
proe精简技巧(proe精简技巧)
ProE streamlining skills
1, change the boot screen
Teach you to change the starting screen, so that you have a good mood every day
Open the installation directory for PROE
TEXT/RESORCE
Inside a picture changed it
2 、 dimensions and tolerances of engineering drawings
@++0.1@#@--0.1@#
3, select the ring surface (Loop Surf)
1. first select the principal surface;
2. press the shift button and don't let go;
3. move the mouse to the boundary of the main surface, at the right bottom of the mouse, pop up "edge: * * *";
4. click the left mouse button to confirm the release of the shift key, OK!
Selection of tangent chains (Tangent)
1. first select a section of the edge;
2. press the shift button and don't let go;
3. move the mouse to any edge tangent to the selected edge, with the word "tangency" at the bottom right of the mouse;
4. click the left mouse button to confirm the release of the shift key, OK
If you have too many broken faces on the Copy surface, you can choose the Boundary method: first select a seed surface, and then click the left mouse button on the shift+ to select the boundary
4, engineering drawings change the number: the original number 200 can be changed to any number, as long as the @d changed to @o, add the digital mother O you want
5, the following fillet method, and now share with you:
The steps for mapping are as follows (version wildfire):
1> creates a chamfer reference stop point on the edge that requires the chamfer;
2> used as a variable chamfer method, first do change chamfer, do not point to complete";
3> hit live switch to transition"
4> click "Transitions""
5> select the part of the chamfer that has not been needed on the gray chamfer that has been generated
6> in the Default (stop case 3) drop-down menu, select "stop at reference""
7> in the "stop references" option bar, select the end of the chamfer you created. The result is shown below:
6, assembly mode tips, you may not know:
When a piece of work is assembled, the workpiece may not be in good position when it is transferred in,
CTRL+AlT+ can press the right mouse button - translation;
You can rotate in CTRL+AlT+ mouse button bit;
You can press the left mouse button of CTRL+AlT+ to translate other pieces that have been assembled
7, you are not tired of wildfires and Miss Grey interface, 2001 interface.
Just add use_pre_wildfire_color_scheme YES to CONFIG
8, delete the trail file
In the config file, add one sentence
Trail_dir f:\temp
* the specified trail file storage directory, each PRO/E to start automatically generate a trail file once, you can specify the trail generated directory regularly delete can also be removed at PRO/E startup, automatically delete the previously generated trail file each time you start PRO/E, only the last generation of trail, this is PROE non normal exit to restore model files
9, "how to input the AutoCAD diagram of 2D to proe."":
In the CAD DWG file into DXF file, and then directly open the DXF file in the PROE, should it be, the best is to set the origin, in the PROE open after the line color change unit (later transferred should be Imperial).
In 10, wildfires in engineering drawing marking, how will the bean number changed to point decimal_marker
COMMA_FOR_METRIC_DUAL?
11, when drawing out the transition line of drawing round:
Tan_edge_display_for_new_views no_disp_tan
12, wildfire 2 how every time you turn out the CAD graphics, the model color and section color are white, how to make it out of the drawings, default to PERO2.0 inside color?
DXf_exprot.pro file
=========================================
Ran
Map_layer dxf_Dimension _Dim
Map_layer dxf_Axis _Axis
Map_layer dxf_hatching _Haych
Map_layer dxf_Text _Text
Map_layer dxf_Table _Table
Map_layer dxf_Format _Format
Map_layer dxf_Continuons_line _Solidine
Map_colar GEOMETRY_COLOR 3
Added to the config file
13. Open the 3D annotation in PRO/E:
14. How do you mark the angle between the curve and the straight
line in the sketch?
Select the curve, the intersection point, the line, and then
press the middle key. This is the basic operation
15, the square marked method engineering diagram:
1:
25 squared
finish writing sth.
{0:25}{1:@+2@#}
2:
{0:25}@+2
It's fine too～
16, proe window how to change size?
The configuration file added to visible_message_lines 1 is OK
Super 17, Toury's engineering skills:
In the national standard, the provisions of the project drawings are cutaway view, bone to bone, tendon location for non dissection,
But in PROE engineering diagram, section view will always place to show all section
Come out. This inevitably results in bone fracture, and PROE
does not provide such an order,
Cutaway to tendons not shown.
18, friends who have the habit of saving often will not save any changes to the parts and produce unnecessary versions. You can add save_objects changed_and_updated to config.pro. This will prompt you because the file has not been saved since it has not been changed. You can also press Alt+w+o to open the system window and enter purge to clear all the old versions in the current working directory.
19, pro/e inside the relationship between father and son can be lifted?
First try to delete the parent feature, and then the child's features are lit in the feature tree. Click cancel at this point.
When you understand the parent-child relationship, you can redefine these sub features first to separate them from the parent. Then try deleting again until there are no more child features.
Such operations are also safe in assembly.
No more, just save the disk before you do this dangerous operation. It's best to activate it in the highest level of assembly drawing
20, usually in the PRO/E DRAWING inside the transfer of
engineering drawings, is not the first time there will be a lot of hidden things are running out, good bother?
Just set it in PROE2001, draw, setup, or, PROE, wildfire, drawing, options:
Ignore_model_layer_status===NO can synchronize PART or ASSEMBLE
Is it convenient?
