清空交换机密码的步骤清空交换机密码的步骤
清空交换机密码步骤:同时也适用于路由器
例如拿Catalyst 3550/3750系列来说: (说明仅方便自己记忆,写在这里不代表什么。)
1.拔掉交换机的电源。
2.按下交换机上的Mode按钮,与此同时,重新插上交换机的电源线。当交换机端口1X上的LED熄灭后可以松开Mode按钮1到2秒,之后将显示一些指示信
息:
The system has been interrupted prior to initializing the flash file
system. The f...
清空交换机密码的步骤
清空交换机密码步骤:同时也适用于路由器
例如拿Catalyst 3550/3750系列来说: (说明仅方便自己记忆,写在这里不代表什么。)
1.拔掉交换机的电源。
2.按下交换机上的Mode按钮,与此同时,重新插上交换机的电源线。当交换机端口1X上的LED熄灭后可以松开Mode按钮1到2秒,之后将显示一些指示信
息:
The system has been interrupted prior to initializing the flash file
system. The following
commands will initialize the flash file system, and finish loading
the operating system
software:
flash_init
load_helper
boot
switch#
3.初始化flash文件系统:
switch#flash_init
4.加载帮助文件:
switch#load_helper
5.显示闪存里的内容:
switch#dir flash:
6.重命名配置文件:
switch#rename flash:config.text flash:config.text.old
7.启动系统,并且如果提示进入setup模式,输入N:
switch#boot
Continue with the configuration dialog? [yes/no]: N
8.进入特权模式,把配置文件名恢复为原始文件名:
Switch#rename flash:config.text.old flash:config.text
9.把配置文件写进内存:
Switch#copy flash:config.text system:running-config
Source filename [config.text]?
Destination filename [running-config]? (到达这一步已基本完成了,后面可以不用管)
10.进入全局配置模式更改密码:
Switch(config)#enable secret {password}
11.退出,并保存到startup-config文件里:
Switch(config)#copy running-config startup-config
二、清空交换机、路由器配置:
Router(config)# erase startup-config
Router(config)#reload
本文档为【清空交换机密码的步骤】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑,
图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。