双卡套管接头
双卡套管接头是由美国人佛瑞德A.雷能在 1947 年发明的。对比于螺纹、扩
孔、单卡套等接头形式,双卡套管接头是一种兼顾密封及安全的小口径管道连接
件。一个优良的双卡套管接头可以做到:
承受高达管子爆破的压力而不泄漏。
可用于真空及高压液体系统。
可在低温状态下工作保证密封。
在管子的最高额定温度下持久的密封。
可重复拆装且保证密封。
双卡套管接头的这些性能使其广泛地应用于仪器仪
表
关于同志近三年现实表现材料材料类招标技术评分表图表与交易pdf视力表打印pdf用图表说话 pdf
、石油化工、电力、气
体等行业。
一.双卡套管接头的结构
二.双卡套管接头的安装步骤:
第一步:将管子插入接头,确保管子端部达到接头底部,并用手指拧紧卡套
螺母。
第二步:在卡套螺母的 6 点位置做一标记。
第三步:用扳手固定接头本体,旋转卡套螺母一又四分之一转,这时所做标
记旋转 540 度,至 9 点钟位置。
三.双卡套管接头的工作原理:
在卡套螺母拧紧一又四分之一转的过程中,接头内部依次完成下面
设计
领导形象设计圆作业设计ao工艺污水处理厂设计附属工程施工组织设计清扫机器人结构设计
好的
动作。
1. 通过螺纹机械式推进,卡套螺母向前运动推动后卡套向前,同时后卡
套推动前卡套向前运动。
2. 接头本体的尖端向内挤压前卡套。
3. 前卡套消除它的内径与管子外径间的公差。
4. 随着后卡套的推进,前卡套向前向内动作,后端抬起,与接头本体斜
面形成密封。
5. 随着管子更大的变形和本体斜面与前卡套接触面的增大,更大的阻力
迫使后卡套向内动作,从而在管子上形成第二道牢固的支撑。
6. 在卡套螺母拧紧一又四分之一转,它前进了 1/16inch(1.52mm),
接头完成了密封,抱紧管子的作用。
卡套接头用 Tube 管的选择
选择卡套接头用 Tube 管要考虑的因素:
1.管子的材料和制造方法
2.管子的外径和壁厚及它们的公差
3.管子外表面的光洁度
4.管子硬度
5.管子的同心度
6.管子的椭圆度
对于金属 Tube 管,一个可靠的方法是采用下面技术标准生产的管子。
适合卡套接头的金属 Tube 管技术标准
来源:PARKER
Swagelok Tube Fitting Instructions
Installation Instructions:
1. Insert tubing into the Swagelok tube fitting. Make sure that the tubing rests firmly
on the shoulder of the tube fitting body and that the nut is finger-tight.
2. Scribe the nut at the 6 o'clock position.
3. While holding fitting body steady with a back-up wrench, tighten the nut 1 1/4 turns
to the 9 o'clock position.
Note: For 1/16, 1/8, and 3/16 in.; 2, 3, and 4 mm tube fittings, tighten the nut 3/4
turn to the 3 o'clock position.
Administrator
图章
Gageability—On initial installation, the Swagelok gap inspection gage assures the
installer or inspector that a fitting has been sufficiently tightened.
Position the Swagelok gap inspection gage next to the gap between the nut and body.
· If the gage will not enter the gap, the fitting is sufficiently tightened.
· If the gage will enter the gap, additional tightening is required.
Reassembly Instructions—You may disassemble and reassemble a Swagelok
tube fitting many times.
1. Insert tubing with pre-swaged ferrules into the fitting body until the front ferrule seats.
2. Rotate the nut with a wrench to the previously pulled-up position, at this point a
significant increase in resistance will be encountered.
3. Tighten slightly with a wrench (approximately a quarter turn).
www.swagelok.com
双卡套管接头TWO FERRULE TUBE FITTING
卡套接头用Tube管的选择
世伟洛克卡套接头安装指南Swagelok Tube Fitting Installation Instructions