机械英语论文-变速箱体噪音(中英文对照)

机械英语论文-变速箱体噪音(中英文对照) 机械英语论文-变速箱体噪音(中英文对照) 机械英语论文 Gearbox Noise? Gearbox Noise? Correlation with Transmission Error and Influence of Bearing Preload Doctoral Thesis in Machine Design TRITA-MMK 2008:19 ISSN 1400-1179 ISRN/KTH/MMK/R-08/19-SE Department of Machine Design Royal institute of Technology SE??100 44 Stockholm, Sweeden ? Mats ?kerblom 2008 ABSTRACT The five appended papers all deal with gearbox noise and vibration. The first paper presents a review of previously published literature on gearbox noise and vibration. The second paper describes a test rig that was specially designed and built for noise testing of gears. Finite element analysis was used to predict the dynamic properties of the test rig, and experimental modal analysis of the ——————————————————————————————————————————————— gearbox housing was used to verify the theoretical predictions of natural frequencies.In the third paper, the influence of gear finishing method and gear deviations on gearbox noise is investigated in what is primarily an experimental study. Eleven test gear pairs were manufactured using three different finishing methods. Transmission error, which is considered to be an important excitation mechanism for gear noise, was measured as well as predicted. The test rig was used to measure gearbox noise and vibration for the different test gear pairs. The measured noise and vibration levels were compared with the predicted and measured transmission error. Most of the experimental results can be interpreted in terms of measured and predicted transmission error. However, it does not seem possible to identify one single parameter,such as measured peak-to-peak transmission error, that can be directly related to measured noise and vibration. The measurements also show that disassembly and reassembly of the gearbox with the same gear pair can change the levels of measured noise and 机械英语论文 Gearbox Noise? vibration considerably.This finding indicates that other factors besides the gears affect gear noise.In the fourth paper, the influence of bearing endplay or preload on gearbox noise and vibration is investigated. Vibration measurements were carried out at torque levels ——————————————————————————————————————————————— of 140 Nm and 400Nm, with 0.15 mm and 0 mm bearing endplay, and with 0.15 mm bearing preload. The results show that the bearing endplay and preload influence the gearbox vibrations. With preloaded bearings, the vibrations increase at speeds over 2000 rpm and decrease at speeds below 2000 rpm, compared with bearings with endplay. Finite element simulations show the same tendencies as the measurements.The fifth paper describes how gearbox noise is reduced by optimizing the gear geometry for decreased transmission error. Robustness with respect to gear deviations and varying torque is considered in order to find a gear geometry giving low noise in an appropriate torque range despite deviations from the nominal geometry due to manufacturing tolerances. Static and dynamic transmission error, noise, and housing vibrations were measured. The correlation between dynamic transmission error, housing vibrations and noise was investigated in speed sweeps from 500 to 2500 rpm at constant torque. No correlation was found between dynamic transmission error and noise. Static loaded transmission error seems to be correlated with the ability of the gear pair to excite vibration in the gearbox dynamic system. Keywords: gear, gearbox, noise, vibration, transmission error, bearing preload. ACKNOWLEDGEMENTS This work was carried out at Volvo Construction Equipment in Eskilstuna and at the Department of Machine Design at the Royal ——————————————————————————————————————————————— Institute of Technology (KTH) in Stockholm. The work was initiated by Professor Jack Samuelsson (Volvo and KTH), Professor S?ren Andersson (KTH), and Dr. Lars Br?the (Volvo).The financial support of the Swedish Foundation for Strategic Research and the Swedish Agency for Innovation Systems – VINNOVA – is gratefully acknowledged. Volvo Construction Equipment is acknowledged for giving me the opportunity to devote time to this 机械英语论文 Gearbox Noise? work.Professor S?ren Andersson is gratefully acknowledged for excellent guidance and encouragement.I also wish to express my appreciation to my colleagues at the Department of Machine Design, and especially to Dr. Ulf Sellgren for performing simulations and contributing to the writing of Paper D, and Dr. Stefan Bj?rklund for performing surface finish measurements.The contributions to Paper C by Dr. Mikael P?rssinen are highly appreciated. All contributionsto this work by colleagues at Volvo are gratefully appreciated. 1 INTRODUCTION 1.1 Background Noise is increasingly considered an environmental issue. This belief is reflected in demands for lower noise levels in many areas of society, including the working environment. Employees spend a lot of time in this environment and noise can lead not only to hearing impairment but also ——————————————————————————————————————————————— to decreased ability to concentrate, resulting in decreased productivity and an increased risk of accidents. Quality, too, has become increasingly important. The quality of a product can be defined as its ability to fulfill customers’ demands. These demands often change over time, and the best competitors in the market will set the standard.Noise concerns are also expressed in relation to construction machinery such as wheel loaders and articulated haulers. T ———————————————————————————————————————————————