1000TEU集装箱船
图号
油水分离器试验程序
Test program for oil-water
separator
图 样 标 记
比例
标记
处数
更改文件号
签字
日期
编 制
打印
校对
共 4 页
第 1 页
审核
材料:
江苏东方造船有限公司
审定
日 期
江苏东方造船有限公司
油水分离器试验程序
图号:
共 4 页 第 2 页
本程序适用于1000TEU集装箱船油水分离器部分的试验程序。
The program uses to test for the oil-water separator of 1000TEU ship.
油水分离器的调试必须在供应服务商在场指导下进行。
Adjust the oil-water separator must under the present direction of the technique server.
1、油水分离器的主要参数
Main parameter of the separator
型号:TCS2.5HD
Model:TCS2.5HD
工作压力:7.8bar
Working pressure: 7.8bar
排放MATCH_
word
word文档格式规范word作业纸小票打印word模板word简历模板免费word简历
_1714127426770_0:<15ppm
Drain standard:<15ppm
泵的排量:2.5 m3/h
Capacity of pump:2.5 m3/h
泵的压头:2.3bar
Press.head of pump: 2.3bar
电机功率:0.75kW
Working power for motor:0.75kW
2、试验前的准备
Preparation before test
2.1检查相关系统及设备已安装完毕,并检验合格。
Check interrelated system and equipments have been installed, and checked eligibility.
2.2 系统管系密性试验检查合格。
The sealing test of system should be passed for checking.
2.3 配制一瓶含油量大于15ppm的水样。
It’s should be have one bottle water sample, and the oiliness magnitude more then 15ppm.
2.4 在污水舱有一定量的污水,供使用。
It’s should be have a little sewage water in the sewage water tank, it’s using for oily water separator.
2.5 调整油分浓度计,将报警点设定为15ppm。
Regulate the oily consistence meter, make the alarm point at the 15ppm.
2.6 打开舱底水舱和分离器之间的所有阀件及分离器排出口的有关阀件。
Open all valves between the bilge water tank and the separator then
江苏东方造船有限公司
油水分离器试验程序
图号:
共 4 页 第 3 页
open all valves on the separator discharge line.
3、油水分离器运行试验
Running test for oil-water separator
3.1 干运行试验,如果管路中无流动信号,5秒延迟后,干运行保护装置报警并停泵。
Dry running test, if there is no flow signal, after 5 second, dry running protect alarm will be activated and the pump will be stopped.
3.2 排放用三通阀自动转换试验。
The automatism conversion test of three-way valve for draining.
3.3 加热器高低温报警试验。
The high/low temp. alarm test of heater.
3.4 油分浓度计报警试验(试验2~3次)。
The alarm test of oily consistence meter(test 2~3 times).
4、设备的检查
Inspection for equipment
4.1 设备运行时, 检查运行情况,要求无泄露及异常振动、响声。
Check running condition of oily water separator, to be required no leaked and no abnormal vibration noise.
4.2 检查控制箱停止/运动开关的位置动作,接线及指示的正确性。
Check the exactness for stop/start switch、connection and direction of control box.
4.3 检查三通自动转换性能,当油含量超过15ppm时,三通阀能立即切换(试验2~3次)。
Check the automatism conversion performance of three-way valve, when the oily consistence more than 15ppm, it must be conversion(test 2~3 times).
4.4 检查加热器工作及报警性能, 并
记录
混凝土 养护记录下载土方回填监理旁站记录免费下载集备记录下载集备记录下载集备记录下载
加热所用时间。
Check the working and alarm conversion of heaters, and then record the time for heating.
4.5 将排放水取样进行化验,并记录化验结果。
Make a test for drain water temple, then record the testing result.
4.6 测量记录电机起动电流,控制设备的冷、热态绝缘电阻值应不小于1 MΩ。
Record starting current of motor and cold & hot insulation resistance of control device, it should be not less than 1 MΩ.
江苏东方造船有限公司
油水分离器试验程序
图号:
共 4 页 第 4 页
油水分离器试验记录
Recording for oily water separator test
1) 加热器试验记录
Record for heater
报警
Alarm
加热时间
Time of heating
加热器
Heater
1#
2#
3#
2) 排放水化验结果
Testing result of the drain water
排放水样
water sample
化验结果
Testing result
No.1
No.2
No.3
3) 电机数据记录
Record for motor
项目
Item
设备
Equipment
起动电流(A)
Starting current
工作电流(A)
Working current
工作电压(V)
Working
voltage
冷态电阻(MΩ)
Cold resistance
热态电阻(MΩ)
Hot
resistance
备 注
Remark
电机
Motor
服务商Server: ___________________ 验船师 Surveyor:______________________
船 东 Owner: ___________________ 厂 检 Shipyard QC:_______________