AS 1110.1—2000
ISO 4014:1999
Australian Standard™
ISO metric hexagon bolts and screws—
Product grades A and B
Part 1: Bolts
[ISO title: Hexagon head bolts—Product grades A and B]
AS
1110
.1
This Australian Standard was prepared by Committee ME/29, Fasteners. It was
approved on behalf of the Council of Standards Australia on 21 April 2000 and
published on 23 June 2000.
The following interests are represented on Committee ME/29:
Australian Building Codes Board
Australian Chamber of Commerce and Industry
Australian Industry Group
Bureau of Steel Manufacturers of Australia
Electricity Supply Association of Australia
Federal Chamber of Automotive Industries
Institute of Materials Engineering Australasia
Metal Building Products Manufacturers Association
Keeping Standards up-to-date
Standards are living documents which reflect progress in science, technology and
systems. To maintain their currency, all Standards are periodically reviewed, and
new editions are published. Between editions, amendments may be issued.
Standards may also be withdrawn. It is important that readers assure themselves
they are using a current Standard, which should include any amendments which
may have been published since the Standard was purchased.
Detailed information about Standards can be found by visiting the Standards
Australia web site at www.standards.com.au and looking up the relevant Standard
in the on-line catalogue.
Alternatively, the printed Catalogue provides information current at 1 January each
year, and the monthly magazine, The Australian Standard, has a full listing of
revisions and amendments published each month.
We also welcome suggestions for improvement in our Standards, and especially
encourage readers to notify us immediately of any apparent inaccuracies or
ambiguities.
This Standard was issued in draft form for comment as DR 00036.
AS 1110.1—2000
Australian Standard™
ISO metric hexagon bolts and screws—
Product grades A and B
Part 1: Bolts
Originated as AS 1110—1972.
Previous edition AS/NZS 1110:1995.
Revised and redesignated, in part, as AS 1110.1—2000.
COPYRIGHT
© Standards Australia International
ii
PREFACE
This Standard was prepared by the Standards Australia Committee ME/29, Fasteners to supersede
AS/NZS 1110:1995, ISO metric precision hexagon bolts and screws, in part.
The objective of this Standard is to provide manufacturers, suppliers and users with the dimensions,
tolerances and material requirements for hexagon head bolts ISO product grades A and B with
ISO metric coarse threads.
This Standard is Part 1 of a two-part series on ISO metric hexagon bolts and screws. Part 2 gives the
dimensions for screws.
This edition has been technically revised and introduces the designations of product grade A and
product grade B in place of the term ‘precision’ which has been used in previous editions.
NOTE: The product grades refer to the quality of the product and to the size of the tolerances where
grade A is the most precise and grade C is the least precise.
This Standard is identical with and has been reproduced from, ISO 4014:1999, Hexagon head bolts—
Product grades A and B.
Statements expressed in mandatory terms in notes to tables and figures are deemed to be requirements
of this Standard.
As this Standard is reproduced from an International Standard, the following applies:
(a)
Its number does not appear on each page of text and its identity is shown only on the cover and
title page.
(b)
In the source text ‘this International Standard’ should read ‘this Australian Standard’.
(c)
A full point should be substituted for a comma when referring to a decimal marker.
References to International Standards should be replaced by references to equivalent Australian
Standards, as follows:
Reference to International Standard Australian Standard
ISO AS
225 Fasteners—Bolts, screws, studs and
nuts—Symbols and designations of
dimensions
—
724 ISO general-purpose metric screw
threads—Basic dimensions
—
888 Bolts, screws and studs—Nominal
lengths, and thread lengths for general
purpose bolts
—
898 Mechanical properties of fasteners
made of carbon steel and alloy steel
4291 Mechanical properties of fasteners
made of carbon, steel and alloy steel
898-1 Part 1: Bolts, screws and studs 4291.1 Part 1: Bolts, screws and studs
965 ISO general purpose metric screw
threads—Tolerances
—
965-1 Part 1: Principles and basic data —
3269 Fasteners—Acceptable inspection —
3506 Mechanical properties of corrosion-
resistant stainless-steel fasteners
—
3506-1 Part 1: Bolts, screws and studs —
4017 Hexagon head screws—Product
grades A and B
1110 ISO metric hexagon head bolts and
screws—Product grades A and B
1110.2 Part 2: Screws
iii
ISO
4042 Fasteners—electroplated coatings
AS
—
4753 Fasteners—Ends of parts with external
metric ISO thread
—
4759 Tolerances for fasteners —
4759-1 Part 1: Bolts, screws, studs and
nuts—Product grades A, B and C
—
6157 Fasteners—Surface discontinuities —
8839 Mechanical properties of fasteners—
Bolts, screws, studs and nuts made of
non-ferrous metals
—
8992 Fasteners—General requirements for
bolts, screws, studs and nuts
—
10683 Fasteners—Non-electrolytically
applied zinc flake coatings
—
iv
CONTENTS
Page
Introduction................................................................................................................... ........v
1
Scope...........................................................................................................................1
2
Normative references ...................................................................................................1
3
Dimensions...................................................................................................................2
4
Specifications and reference standards ......................................................................10
5
Designation ................................................................................................................10
Bibliography ................................................................................................................... .....11
Standards Australia
Standards Australia is an independent company, limited by guarantee, which prepares and publishes
most of the voluntary technical and commercial standards used in Australia. These standards are
developed through an open process of consultation and consensus, in which all interested parties are
invited to participate. Through a Memorandum of Understanding with the Commonwealth government,
Standards Australia is recognized as Australia’s peak national standards body.
Australian Standards
Australian Standards are prepared by committees of experts from industry, governments, consumers
and other relevant sectors. The requirements or recommendations contained in published Standards are
a consensus of the views of representative interests and also take account of comments received from
other sources. They reflect the latest scientific and industry experience. Australian Standards are kept
under continuous review after publication and are updated regularly to take account of changing
technology.
International Involvement
Standards Australia is responsible for ensuring that the Australian viewpoint is considered in the
formulation of international Standards and that the latest international experience is incorporated in
national Standards. This role is vital in assisting local industry to compete in international markets.
Standards Australia represents Australia at both ISO (The International Organization
for Standardization) and the International Electrotechnical Commission (IEC).
Electronic Standards
All Australian Standards are available in electronic editions, either downloaded individually from our Web
site, or via on-line and CD ROM subscription services.
ISBN 0 7337 3399 9 Printed in Australia
AS 1110.1-2000 ISO metric hexagon bolts and screws-Product grades A and B - Bolts
本文档为【AS 1110.1-2000 ISO metric hexagon bolts and screws - Product grades A and B - Bolts】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑,
图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。