UC3842

©2002 Fairchild Semiconductor Corporation www.fairchildsemi.com Rev. 1.0.1 Features • Low Start up Current • Maximum Duty Clamp • UVLO With Hysteresis • Operating Frequency up to 500KHz Description The UC3842/UC3843/UC3844/UC3845 are fixed frequencycurrent-mode PWM controller. They are specially designed for Off-Line and DC to DC converter applications with minimum external components. These integrated circuits feature a trimmed oscillator for precise duty cycle control, a temperature compensated reference, high gain error amplifier, current sensing comparator and a high current totempole output for driving a Power MOSFET. The UC3842 and UC3844 have UVLO thresholds of 16V (on) and 10V (off). The UC3843 and UC3845 are 8.5V(on) and 7.9V (off). The UC3842 and UC3843 can operate within 100% duty cycle. The UC3844 and UC3845 can operate with 50% duty cycle. 8-DIP 14-SOP 1 1 8-SOP 1 Internal Block Diagram UC3842/UC3843/UC3844/UC3845 SMPS Controller * NORMALLY 8DIP/8SOP PIN NO. * ( ) IS 14SOP PINNO. * TOGGLE FLIP FLOP USED ONLY IN UC3844, UC3845 UC3842/UC3843/UC3844/UC3845 2 Absolute Maximum Ratings Note: 1. Board Thickness 1.6mm, Board Dimension 76.2mm ×114.3mm, (Reference EIA / JSED51-3, 51-7) 2. Do not exceeed PD and SOA (Safe Operation Area) Power Dissipation Curve Thermal Data Pin Array Parameter Symbol Value Unit Supply Voltage VCC 30 V Output Current IO ±1 A Analog Inputs (Pin 2.3) V(ANA) -0.3 to 6.3 V Error Amp Output Sink Current ISINK (E.A) 10 mA Power Dissipation at TA≤25°C (8DIP) PD(Note1,2) 1200 mW Power Dissipation at TA≤25°C (8SOP) PD(Note1,2) 460 mW Power Dissipation at TA≤25°C (14SOP) PD(Note1,2) 680 mW Storage Temperature Range TSTG -65 ~ +150 °C Lead Temperature (Soldering, 10sec) TLEAD +300 °C Characteristic Symbol 8-DIP 8-SOP 14-SOP Unit Thermal Resistance Junction-ambient Rthj-amb(MAX) 100 265 180 °C/W 800 700 600 500 400 300 900 1000 1100 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 AMBIENT TEMPERATURE (℃) PO W ER D IS SI PA TI O N (m W ) 1200 8DIP 14SOP 8SOP 800 700 600 500 400 300 900 1000 1100 0 10 20 30 40 5030 40 50 60 70 8060 70 80 90 100 11090 100 110 120 130 140120 130 140 150 AMBIENT TEMPERATURE (℃) PO W ER D IS SI PA TI O N (m W ) 1200 8DIP 14SOP 8SOP VCC GND PWR GND COMP 1 N/C 2 VFB N/C 3 4 VREF N/C PWR VC 14 13 12 11 CURRENT SENSE 5 N/C RT/CT 6 7 OUTPUT10 9 8 COMP 1 VFB 2 CURRENT SENSE RT/CT 3 4 VREF VCC OUTPUT GND 8 7 6 5 8DIP,8SOP 14SOP VCC GND PWR GND COMP 1 N/C 2 VFB N/C 3 4 VREF N/C PWR VC 14 13 12 11 CURRENT SENSE 5 N/C RT/CT 6 7 OUTPUT10 9 8 VCC GND PWR GND COMP 1 N/C 2 VFB N/C 3 4 VREF N/C PWR VC 14 13 12 11 CURRENT SENSE 5 N/C RT/CT 6 7 OUTPUT10 9 8 COMP 1 VFB 2 CURRENT SENSE RT/CT 3 4 VREF VCC OUTPUT GND 8 7 6 5 COMP 1 VFB 2 CURRENT SENSE RT/CT 3 4 VREF VCC OUTPUT GND 8 7 6 5 8DIP,8SOP 14SOP UC3842/UC3843/UC3844/UC3845 3 Electrical Characteristics (VCC=15V, RT=10kΩ, CT=3.3nF, TA= 0°C to +70°C, unless otherwise specified) Parameter Symbol Conditions Min. Typ. Max. Unit REFERENCE SECTION Reference Output Voltage VREF TJ = 25°C, IREF = 1mA 4.90 5.00 5.10 V Line Regulation ∆VREF 12V ≤ VCC ≤ 25V - 6 20 mV Load Regulation ∆VREF 1mA ≤ IREF ≤ 20mA - 6 25 mV Short Circuit Output Current ISC TA = 25°C - -100 -180 mA OSCILLATOR SECTION Oscillation Frequency f TJ = 25°C 47 52 57 kHz Frequency Change with Voltage ∆f/∆VCC 12V ≤ VCC ≤ 25V - 0.05 1 % Oscillator Amplitude VOSC - - 1.6 - VP-P ERROR AMPLIFIER SECTION Input Bias Current IBIAS - - -0.1 -2 µA Input Voltage VI(E>A) Vpin1 = 2.5V 2.42 2.50 2.58 V Open Loop Voltage Gain GVO 2V ≤ VO ≤ 4V (Note3) 65 90 - dB Power Supply Rejection Ratio PSRR 12V ≤ VCC ≤ 25V (Note3) 60 70 - dB Output Sink Current ISINK Vpin2 = 2.7V, Vpin1 = 1.1V 2 7 - mA Output Source Current ISOURCE Vpin2 = 2.3V, Vpin1 = 5V -0.6 -1.0 - mA High Output Voltage VOH Vpin2 = 2.3V, RL = 15kΩ to GND 5 6 - V Low Output Voltage VOL Vpin2 = 2.7V, RL = 15kΩ to Pin 8 - 0.8 1.1 V CURRENT SENSE SECTION Gain GV (Note 1 & 2) 2.85 3 3.15 V/V Maximum Input Signal VI(MAX) Vpin1 = 5V(Note 1) 0.9 1 1.1 V Power Supply Rejection Ratio PSRR 12V ≤ VCC ≤ 25V (Note 1,3) - 70 - dB Input Bias Current IBIAS - - -3 -10 µA OUTPUT SECTION Low Output Voltage VOL ISINK = 20mA - 0.08 0.4 V ISINK = 200mA - 1.4 2.2 V High Output Voltage VOH ISOURCE = 20mA 13 13.5 - V ISOURCE = 200mA 12 13.0 - V Rise Time tR TJ = 25°C, CL= 1nF (Note 3) - 45 150 ns Fall Time tF TJ = 25°C, CL= 1nF (Note 3) - 35 150 ns UNDER-VOLTAGE LOCKOUT SECTION Start Threshold VTH(ST) UC3842/UC3844 14.5 16.0 17.5 V UC3843/UC3845 7.8 8.4 9.0 V Min. Operating Voltage (After Turn On) VOPR(MIN) UC3842/UC3844 8.5 10.0 11.5 V UC3843/UC3844 7.0 7.6 8.2 V UC3842/UC3843/UC3844/UC3845 4 Electrical Characteristics (Continued) (VCC=15V, RT=10kΩ, CT=3.3nF, TA= 0°C to +70°C, unless otherwise specified) Adjust VCC above the start threshould before setting at 15V Note: 1. Parameter measured at trip point of latch 2. Gain defined as: 3. These parameters, although guaranteed, are not 100 tested in production. Figure 1. Open Loop Test Circuit High peak currents associated with capacitive loads necessitate careful grounding techniques Timing and bypass capacitors should be connected close to pin 5 in a single point ground. The transistor and 5kΩ potentiometer are used to sample the oscillator waveform and apply an adjustable ramp to pin 3. Parameter Symbol Conditions Min. Typ. Max. Unit PWM SECTION Max. Duty Cycle D(Max) UC3842/UC3843 95 97 100 % D(Max) UC3844/UC3845 47 48 50 % Min. Duty Cycle D(MIN) - - - 0 % TOTAL STANDBY CURRENT Start-Up Current IST - - 0.45 1 mA Operating Supply Current ICC(OPR) Vpin3=Vpin2=ON - 14 17 mA Zener Voltage VZ ICC = 25mA 30 38 - V A ∆Vpin1 ∆Vpin3 ------------------= UC3842 ,0 ≤ Vpin3 ≤ 0.8V UC3842/UC3843/UC3844/UC3845 5 Figure 2. Under Voltage Lockout During Under-Voltage Lock-Out, the output driver is biased to a high impedance state. Pin 6 should be shunted to ground with a bleeder resistor to prevent activating the power switch with output leakage current. Figure 3. Error Amp Configuration Figure 4. Current Sense Circuit Peak current (IS) is determined by the formula: A small RC filter may be required to suppress switch transients. UC3842/44 UC3843/45 IS MAX( ) 1.0VRS ------------= UC3842/UC3843/UC3844/UC3845 6 Figure 5. Oscillator Waveforms and Maximum Duty Cycle Oscillator timing capacitor, CT, is charged by VREF through RT and discharged by an internal current source. During the discharge time, the internal clock signal blanks the output to the low state. Selection of RT and CT therefore determines both oscillator frequency and maximum duty cycle. Charge and discharge times are determined by the formulas: tc = 0.55 RT CT Frequency, then, is: f=(tc + td)-1 Figure 8. Shutdown Techniques Figure 6. Oscillator Dead Time & Frequency Figure 7. Timing Resistance vs Frequency tD RTCTIn 0.0063RT 2.7– 0.0063RT 4– ----------------------------------------  = ForRT 5KΩ f 1.8 RTCT ---------------=,> (Deadtime vs CT RT > 5kΩ) UC3842/UC3843/UC3844/UC3845 7 Shutdown of the UC3842 can be accomplished by two methods; either raise pin 3 above 1V or pull pin 1 below a voltage two diode drops above ground. Either method causes the output of the PWM comparator to be high (refer to block diagram). The PWM latch is reset dominant so that the output will remain low until the next clock cycle after the shutdown condition at pins 1 and/or 3 is removed. In one example, an externally latched shutdown may be accomplished by adding an SCR which will be reset by cycling VCC below the lower UVLO threshold. At this point the reference turns off, allowing the SCR to reset. Figure 9. Slope Compensation A fraction of the oscillator ramp can be resistively summed with the current sense signal to provide slope compensation for converters requiring duty cycles over 50%. Note that capacitor, CT, forms a filter with R2 to suppress the leading edge switch spikes. Temperature (°C) Figure 10. Temperature Drift (Vref) Temperature (°C) Figure 11. Temperature Drift (Ist) Temperature (°C) Figure 12. Temperature Drift (Icc) UC3842/UC3843 UC3842/UC3843/UC3844/UC3845 8 Mechanical Dimensions Package 6.40 ±0.20 3.30 ±0.30 0.130 ±0.012 3.40 ±0.20 0.134 ±0.008 #1 #4 #5 #8 0.252 ±0.008 9. 20 ±0 .2 0 0. 79 2. 54 0. 10 0 0. 03 1 ( ) 0. 46 ±0 .1 0 0. 01 8 ±0 .0 04 0. 06 0 ±0 .0 04 1. 52 4 ±0 .1 0 0. 36 2 ±0 .0 08 9. 60 0. 37 8 M AX 5.08 0.200 0.33 0.013 7.62 0~15° 0.300 MAX MIN 0.25 +0.10 –0.05 0.010 +0.004 –0.002 8-DIP UC3842/UC3843/UC3844/UC3845 9 Mechanical Dimensions (Continued) Package 8-SOP 4. 92 ±0 .2 0 0. 19 4 ±0 .0 08 0. 41 ±0 .1 0 0. 01 6 ±0 .0 04 1. 27 0. 05 0 5.72 0.225 1.55 ±0.20 0.061 ±0.008 0.1~0.25 0.004~0.001 6.00 ±0.30 0.236 ±0.012 3.95 ±0.20 0.156 ±0.008 0.50 ±0.20 0.020 ±0.008 5. 13 0. 20 2 M AX #1 #4 #5 0~ 8° #8 0. 56 0. 02 2 ( ) 1.80 0.071 M AX 0. 10 M AX 0. 00 4 MAX MIN + 0.10 -0.05 0.15 + 0.004 -0.002 0.006 UC3842/UC3843/UC3844/UC3845 10 Mechanical Dimensions (Continued) Package 8. 56 ±0 .2 0 0. 33 7 ±0 .0 08 1. 27 0. 05 0 5.72 0.225 1.55 ±0.10 0.061 ±0.004 0.05 0.002 6.00 ±0.30 0.236 ±0.012 3.95 ±0.20 0.156 ±0.008 0.60 ±0.20 0.024 ±0.008 8. 70 0. 34 3 M AX #1 #7 #8 0~ 8° #14 0. 47 0. 01 9 ( ) 1.80 0.071 M AX 0. 10 M AX 0. 00 4 MAX MIN + 0. 10 - 0. 05 0. 20 + 0. 00 4 - 0. 00 2 0. 00 8 + 0. 10 - 0. 05 0. 40 6 + 0. 00 4 - 0. 00 2 0. 01 6 14-SOP UC3842/UC3843/UC3844/UC3845 11 Ordering Information Product Number Package Operating Temperature UC3842N 8-DIP 0 ~ + 70°C UC3843N UC3844N UC3845N UC3842D1 8-SOP UC3843D1 UC3844D1 UC3845D1 UC3842D 14-SOP UC3843D UC3844D UC3845D UC3842/UC3843/UC3844/UC3845 2/19/02 0.0m 001 Stock#DSxxxxxxxx  2002 Fairchild Semiconductor Corporation LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.