n型硅电池做成的组件

HIT photovoltaic module n electrode Thin mono crystalline silicon wafer Ultra-thin amorphous silicon layer Ultra-thin amorphous silicon layer HIT ® Solar Cell Structure Three tabs no rm al iz ed o ut pu t p ow er Changes in generated power daytime HIT time approx. 10%up Module temp.75℃ Kobe (Japan), 24. July 2007, faced to south, tilt angle 30° 0.8 0.5 5 7 9 11 13 15 17 19 c-Si E N Benefit in Terms of Performance The SANYO HIT(Heterojunction with Intrinsic Thin layer) solar cell is made of a thin mono crystalline silicon wafer surrounded by ultra-thin amorphous silicon layers. This product provides the industry's leading performance and value using state-of-the-art manufacturing techniques. High performance at high temperatures Environmentally-Friendly Solar Cell More Clean Energy HIT can generate more clean Energy than other conventional crystalline solar cells. SANYO HIT solar modules are 100% emission free, have no moving parts and produce no noise.The dimensions of the HIT modules allow space-saving installation and achievement of maximum output power possible on given roof area. Special Features Even at high temperatures, the HIT solar cell can maintain higher efficiency than a conventional crystalline silicon solar cell. HIT cell technology 19.0*% HIT is a registered trademark of SANYO Electric Co., Ltd. The name "HIT " comes from "Heterojunction with intrinsic Thin-layer" which is an original technology of SANYO Electric Co., Ltd. - Carrier recombination loss - Optical absorption loss - Resistance loss Improvement of the cell efficiency to reduce - Reducing electrical loss between the cell fingers and tabs - Making the tab width thinner to expand the light receiving surface Three tabs application New tab design R&D technology adaptation Anti- reflection glass Light capturing technology - Reducing reflection and scattering of incoming light - Improving generated electricity levels in morning and evening times HIT-N240SE10 HIT-N235SE10 HIT-N230SE10 The HIT cell and module have very high conversion efficiency in mass production. * For HIT-N240SE10 190 W/m2 HIT-N240SE10 HIT-N235SE10 19.0%21.6% 18.6%21.1% HIT-N230SE10 18.2%20.7% Model Cell E�ciency Module E�ciency Output / m2 190 W/m2 186 W/m2 182 W/m2 CAUTION! Please read the installation manual carefully before using the products. Due to our policy of continual improvement the products covered by this brochure may be changed without notice. Electrical and Mechanical Characteristics 11 /1 0 Stahlgruberring 4 81829 Munich, Germany Tel.+49-(0)89-460095-0 Fax.+49-(0)89-460095-170 http://www.sanyo-solar.eu email: info.solar@sanyo-solar.eu SANYO Component Europe GmbH Solar Division http://www.sanyo.com/solar/ SANYO Electric Co.,Ltd. Solar Division unit: mm Dimensions and weight Weight: 15 Kg Weight/m2: 11,9 Kg/m2 Front side Section A-A Section B-B A A B B 798 15 80 (24) 35 (12) 35 35 Backside L a b e l C o n n e c t o r M C 3 (762) (3 30 ) 4-Ø7 JUNCTION BOX (1 23 ) (9 60 ) Please consult your local dealer for more information. Guarantee Power output: 10 years (90% of Pmin) 25 years (80% of Pmin) Product workmanship: 5 years (Based on guarantee document) Materials Cell material: 5 inch HIT cells Glass material: AR coated tempered glass Frame materials: Black anodized aluminium Connectors type: MC3 Electrical Protection Class ll Safety tested, IEC 61730 ●　 Periodic Inspection●　 1343200000 Certi�cates Member of IEC 61215 IEC 61730 E N 235 45.9 41.7 1.10 49.0 1.17 182 49.4 4.71 41.1 4.44 240 240 -0.30 -0.131 1.76 44.0 Models HIT-NxxxSE10 1000 +10/-5* 15 240 52.4 5.85 43.7 5.51 240 235 230 44.7 43.8 41.0 40.6 1.09 1.08 48.4 47.8 1.17 1.17 175 48.3 4.70 39.9 4.38 230 179 48.9 4.70 40.5 4.41 235 44.0 235 230 -0.30 -0.128 1.75 -0.30 -0.130 1.75 44.0 230 51.2 5.83 42.3 5.45 230 235 51.8 5.84 43.0 5.48 235 HIT-N240SE10, HIT-N235SE10, HIT-N230SE10 At low irradiance Maximum power (Pmax) [W] Max. power voltage (Vmp) [V] Max. power current (Imp) [A] Open circuit voltage (Voc) [V] Short circuit current (Isc) [A] Note: Low irradiance: Air mass 1.5 spectrum, Irradiance = 200W/m2, cell temperature = 25°C Maximum power (Pmax) [W] Max. power voltage (Vmp) [V] Max. power current (Imp) [A] Open circuit voltage (Voc) [V] Short circuit current (Isc) [A] At NOCT Note: Nominal Operating Cell Temperature : Air mass 1.5 spectrum, Irradiance = 800W/m2, Air temperature = 20°C , wind speed 1 m/s Temperature (NOCT) [°C] Temperature characteristics Temperature coe�cient of Pmax [%/°C] Temperature coe�cient of Voc [V/°C] Temperature coe�cient of lsc [mA/°C] Maximum power (Pmax) [W] Max. power voltage (Vmp) [V] Max. power current (Imp) [A] Open circuit voltage (Voc) [V] Short circuit current (Isc) [A] Maximum system voltage [V] Electrical data (at STC) Output power tolerance [%] Note: Standard Test Conditions: Air mass 1.5, Irradiance = 1000W/m2, cell temperature = 25°C Maximum over current rating [A] Dependence on irradiance Reference data for model HIT-N240E10 (Cell temperature: 25oC) Cu rr en t[ A ] 0.00 1.00 2.00 3.00 4.00 5.00 6.00 7.00 Voltage[V] 100 20 30 40 50 60 1000W/m 2 800W/m 2 600W/m 2 400W/m 2 200W/m 2 * All modules measured by SANYO facility have output with positive tolerance HIT-N240-235-230-EN_f HIT-N240-235-230-EN_b