Driving Unipolar Stepper Motors Using C51C251

C51 Microcontrollers Application Note Driving Unipolar Stepper Motors Using C51/C251 Introduction Stepper motors are commonly used in accurate motion control. They allow to control any motion with high precision by counting the number of steps applied to the motor. Most of systems controlling stepper motors are embedded systems such as printer, scanner or floppy disk drive. This application note describes how to drive a unipolar stepper motor with the Programmable Counter Array of an Atmel C51/C251 microcontroller. Description C51/C251 microcontroller output pins cannot directly drive stepper motors. These have to be powered before being applied to the stepper motor. This document explains uses the Programmable Counter Array (PCA) of the micro- controller to generate the control signals to the Power Interface. The Power Interface allows the microcontroller to drive enough current into coils of a stepper motor. There are two advantages to using PCA. First of all, PCA provides greater accuracy than toggling pins in software because the toggle occurs before the interrupt request is serviced. Thus, interrupt response time does not affect the accuracy of the output. Secondly the microcontroller CPU is left free for application task execution while the PCA drives stepper motors. There are two major types of stepper motors: Permanent magnet stepper motors (uni- polar stepper motors and bipolar stepper motors) and variable reluctance stepper motors (hybrid stepper motors). Rev. 4214B–8051–12/02 1 Figure 1. System Configuration 2 C51/C251 Application Note Identification of Stepper Motor There are several types of stepper motors, these cannot be driven in the same way. In this application note, we have chosen to drive a unipolar stepper motor (see Figure 2). For more information you will find schemes to identify the other types of stepper motors. Unipolar Stepper Motor Unipolar stepper motors are characterised by their center-tapped windings. Figure 2. Unipolar Stepper Motors Coils Bipolar Stepper Motor Bipolar stepper motors are designed with separate coils. Figure 3. Bipolar Stepper Motor Coils Variable Reluctance Variable reluctance stepper motor (also called hybrid motors) are characterised by one common lead. Stepper Motor Power Interface C51/C251 ControlSignals Control Signals Powered 4214B–8051–12/02 C51/C251 Application Note Figure 4. Hybrid Stepper Motor Coils 3 Driving Unipolar Stepper Motors There are three ways to drive unipolar stepper motors (one phase on, two phase on or half step), each one has some advantages and disavantages. One Phase On Mode (Full Step mode) Table 1. One Phase On Sequence Step 1a 1b 2a 2b 1 1 0 0 0 2 0 1 0 0 3 0 0 1 0 4 0 0 0 1 4214B–8051–12/02 Figure 5. One Phase Steps 4 C51/C251 Application Note In one phase mode, each successive coil is energized in turn. One phase mode pro- duces smooth rotations and the lowest power comsumption of the three modes. Steps are applied in order from one to four. After step four, the sequence is repeated from step one. Applying steps from one to four makes the motor run clockwise, reversing the order of step from four to one will make the motor run counter-clockwise. Figure 6. One Phase On Steps Sequence 4214B–8051–12/02 C51/C251 Application Note Two Phases On Mode Table 2. Two Phases On Sequence 5 (Alternate Full step Mode) Figure 7. Two Phases On Steps In two phase mode, successive pairs of adjacent coils are energised in turn, motion is not as smooth as in one phase mode, power comsumption is more important but it pro- duces greater torque. As in one phase mode, applying the steps in order makes the stepper motor run clock- wise and reversing order makes it turn counter-clockwise. Step 1a 1b 2a 2b 1 1 0 0 1 2 1 1 0 0 3 0 1 1 0 4 0 0 1 1 4214B–8051–12/02 Figure 8. Two Phases On Steps Sequence 6 C51/C251 Application Note Half Step Mode Table 3. Half Step Sequence The half step sequence is a mix of one phase on and two phase on sequences. The main advantage of this mode is to increase by two the nominal number of steps of your stepper motor. By example, an unipolar stepper motor of 24 steps of 15 degrees each "becomes", when we use half step mode, a stepper motor of 48 steps of 7.5 degrees. Step 1a 1b 2a 2b 1 1 0 0 1 2 1 0 0 0 3 1 1 0 0 4 0 1 0 0 5 0 1 1 0 6 0 0 1 0 7 0 0 1 1 8 0 0 0 1 4214B–8051–12/02 C51/C251 Application Note Figure 9. Half Step Sequence 7 4214B–8051–12/02 Figure 10. Half Step Sequence 8 C51/C251 Application Note Hardware The following schematics shows the power interface between the Atmel C51/C251 and a stepper motor. The four PCA pins must have the following hardware connected. Coils are connected with both center-tapped windings connected to 12V power supply. Figure 11. Power Interface In this configuration, the stepper motor is opto-isolated from the microcontroller with a high protection level. The 2N2222A transistor helps to drive enough current in 4N37 led (via 1kΩ resistor). Stepper motor power is given by 12V power supply via TIP121 transistor. Diode on stepper motor coil is used to prevent inductive kicks produced when coil is turned off. C51/C251 100K 12V Stepper P1.x/CEXx 1K 5V 2N2222A 4N37 1K TIP121 Motor Coil X412V GND5V GND center-tapped winding 1N 40 07 4214B–8051–12/02 C51/C251 Application Note Driving Two Stepper It is possible to drive two stepper motors at the same time with only four PCA channels. 9 Motors with Only One PCA For this, we will use the the Two Phase On mode (see Table 2 and Figure 6). In this mode, signals 1 and 2 are respectively opposite waveforms of signals 3 and 4. Thus, it is possible to have the four signals needed for one stepper motor with only two PCA channels and two logical inverters. Software The software of this application note (Given in appendix A), written in C language allows to make a motor turn NB_LOOP loops clockwise (or counter-clockwise) direction in half step mode. NB_LOOP and clockwise (or counter-clockwise) are defined in constant variable at the beginning of code, and must be defined before compilation. The user also needs to define (via constant variable) the number of steps of the motor. The unipolar stepper motor will be driven with PCA via Power Interface described in section 3. - The following software initializes CEX0 to CEX3 of Programmable Counter Array in High Speed Output Mode - Timer 0 is configured in 8 bit auto-reload mode - Clock of the PCA is given by overflow of Timer 0. - PCA interrupt vector at address 0x0033h is also used. If speed precision is not very important in the application it is possible to use Fosc/12 or Fosc/4 for PCA clock input, it will leave Timer 0 free for the application itself. Stepper Motor 1 Power Interface Control Signals Control Signals Powered C51/C251 Stepper Motor 2 Power Interface Control Signals Control Signals Powered 1 2 4214B–8051–12/02 The speed of the stepper motor may be calculated with the formula: 10 C51/C251 Application Note SPEED = Speed in rotations per minute NBSTEP = Number of step of the motor, in general written on the stepper motor itself (48, 96, 200..) Fosc = Frequency of the oscillator in Hertz. For example, when using stepper motor with 200 steps and a 12 Mhz oscillator and loading THO with 0xFC, the speed is 12.2 rotations per minute. With the same formula THO is found by: The table below lists the values of speed for different oscillator frequencies and nominal number of steps of the motor, when using Fosc / 12 and Fosc / 4 as PCA clock input. Value for other oscillator frequency or number of steps can be found easily by arithmetic operation. For example, at Fosc = 12 MHz and clock input = Fosc / 12 , NBSTEP = 96 we found 76.295 rotations per minute. If another motor of 48 steps is used instead, we found now 2*76.295 rotations per minute. Note: Above values are theoretical for high speed rotation, motors are limited by needed torque. Sometimes it will be necessary to start the motor slowly and accelerate it after few seconds. Rot/Min Fosc (MHz) Nb of Step 210.941 11.0592 96 Fosc / 4 70.314 11.0592 96 Fosc / 12 101.252 11.0592 200 Fosc / 4 33.751 11.0592 200 Fosc / 12 178.705 12 96 Fosc / 4 76.295 12 96 Fosc / 12 109.865 12 200 Fosc / 4 36.622 12 200 Fosc / 12 305.180 16 96 Fosc / 4 101.723 16 96 Fosc / 12 146.487 16 200 Fosc / 4 48.829 16 200 Fosc / 12 * 0xFFFF * [ 0xFF - TH0 ] Fosc 12 * NB STEP 8 SPEED = 60 40 * Fosc NB STEP * 0xFFFF * SPEEDTH0 = 0xFF - 4214B–8051–12/02 C51/C251 Application Note Appendix A: Software 11 MAIN.C /*C************************************************************************************ * NAME : Stepper.c *-------------------------------------------------------------------------------------- * CREATED_BY : Eric TINLOT * CREATION_DATE : 05/02/01 *-------------------------------------------------------------------------------------- * PURPOSE : Driving unipolar stepper motor in half step mode using PCA. **************************************************************************************/ /*_____ I N C L U D E S _______________________________________________________________*/ #include "89C51RD2.H" /* sfr definition file */ /*_____ D E C L A R A T I O N__________________________________________________________*/ /*_____ M A C R O S __________________________________________________________________*/ #define ENABLE_ALL_IT ( EA = 1 ) #define PCA_ON ( CCON |= 0x40) #define PCA_OFF ( CCON &= 0xBF) /*_____ D E F I N I T I O N ___________________________________________________________*/ #define NB_LOOP 10/* place here the number of loop desired */ /* select rotation direction here */ #define CLOCKWISE #define NB_STEP 48 /* define by stepping motor itself */ #define P_HIGH 0xFF #define P_LOW 0x00 long int nb_it=0; /*F************************************************************************************ * NAME :ccaxh_reload_value *-------------------------------------------------------------------------------------- * AUTHOR :Eric TINLOT * DATE :05/02/01 *-------------------------------------------------------------------------------------- * PURPOSE:Load value in PCA register CCAPxH * INPUTS:value for CCAP0H,CCAP1H,CCAP2H,CCAP3H 4214B–8051–12/02 * OUTPUTS:void 12 C51/C251 Application Note **************************************************************************************/ void ccapxh_reload_value(char h0, char h1, char h2, char h3) { CCAP0H = h0; CCAP1H = h1; CCAP2H = h2; CCAP3H = h3; } /*F************************************************************************************ * NAME :timer0_init *-------------------------------------------------------------------------------------- * AUTHOR :Eric TINLOT * DATE :05/02/01 *-------------------------------------------------------------------------------------- * PURPOSE:init timer 0 for PCA clock * INPUTS :void * OUTPUTS:void **************************************************************************************/ void timer0_init(void) { TH0 = 0xB3; TL0 = 0xB3; TMOD = TMOD | 0x02; TCON = TCON | 0x10; } /*F************************************************************************************ * NAME :pca_init *-------------------------------------------------------------------------------------- * AUTHOR :Eric TINLOT * DATE :05/02/01 *-------------------------------------------------------------------------------------- * PURPOSE:init pca to run in High speed Output * INPUTS :void * OUTPUTS:void **************************************************************************************/ void pca_init(void) { CCAP0L = P_HIGH; CCAP1L = P_HIGH; CCAP2L = P_HIGH; CCAP3L = P_HIGH; #ifdef CLOCKWISE /* pca register initialisation for CLOCKWISE rotation */ ccapxh_reload_value(0x5F,0x00,0x00,0x1F); #else /* COUNTER_CLOCKWISE */ /* pca register initialisation for COUNTER CLOCKWISE rotation */ 4214B–8051–12/02 C51/C251 Application Note ccapxh_reload_value(0x1F,0x00,0x00,0x5F); 13 #endif CCAPM0 = 0x4D; /* enable High Speed Output mode on CEX0 - CEX3 */ CCAPM1 = 0x4D; CCAPM2 = 0x4D; CCAPM3 = 0x4D; /* PCA Clock Select */ CMOD = 0x04; /* CMOD = 0x04 -> pca clock = timer0 overflow */ /* CMOD = 0x00 -> pca clock = Fosc/12 */ /* CMOD = 0x02 -> pca clock = Fosc/4 */ CH = 0xFF; CL = 0xFF; EC = 0x01; } /*F************************************************************************************ * NAME :PCA - interrupt program *-------------------------------------------------------------------------------------- * AUTHOR :Eric TINLOT * DATE:05/02/01 *-------------------------------------------------------------------------------------- * PURPOSE:identify toggle pin and prepare pca register for next toggle * nb_it variable, enable to count number of loop * INPUTS :void * OUTPUTS:void **************************************************************************************/ PCA() interrupt 6 using 1 /* Int Vector at 000BH, Reg Bank 1 */ { #ifdef CLOCKWISE if (CCF0==1 && CEX0==0) { nb_it++; CCF0 = 0; CCAP0H = 0xFF; } if (CCF1==1 && CEX1==0) { CCF1 = 0; CCAP1H = 0x3F; } if (CCF2==1 && CEX2==0) { CCF2 = 0; CCAP2H = 0x7F; } if (CCF3==1 && CEX3==0) { CCF3 = 0; CCAP3H = 0xBF; } if (CCF0==1 && CEX0==1) { CCF0 = 0; CCAP0H = 0x5F; } if (CCF1==1 && CEX1==1) { CCF1 = 0; CCAP1H = 0x9F; } if (CCF2==1 && CEX2==1) { CCF2 = 0; CCAP2H = 0xDF; } if (CCF3==1 && CEX3==1) { CCF3 = 0; CCAP3H = 0x1F; } #else /* COUNTER_CLOCKWISE */ if (CCF0==1 && CEX0==0) { nb_it++; CCF0 = 0; CCAP0H = 0xBF; } if (CCF1==1 && CEX1==0) { CCF1 = 0; CCAP1H = 0x7F; } if (CCF2==1 && CEX2==0) { CCF2 = 0; CCAP2H = 0x3F; } if (CCF3==1 && CEX3==0) { CCF3 = 0; CCAP3H = 0xFF; } 4214B–8051–12/02 if (CCF0==1 && CEX0==1) { CCF0 = 0; CCAP0H = 0x1F; } 14 C51/C251 Application Note if (CCF1==1 && CEX1==1) { CCF1 = 0; CCAP1H = 0xDF; } if (CCF2==1 && CEX2==1) { CCF2 = 0; CCAP2H = 0x9F; } if (CCF3==1 && CEX3==1) { CCF3 = 0; CCAP3H = 0x5F; } #endif } /*F************************************************************************************ * NAME :main *-------------------------------------------------------------------------------------- * AUTHOR:Eric TINLOT * DATE :05/02/01 *-------------------------------------------------------------------------------------- * PURPOSE:call init subroutines and run stepper motor for nb_loop * INPUTS :void * OUTPUTS:void **************************************************************************************/ void main(void) { long int tocount; tocount = 2 * (NB_STEP / 8) * NB_LOOP; /* compute number of IT needed for NB LOOP*/ timer0_init(); /* init Timer 0 for pca clock */ pca_init(); /* init pca to run in High speed Output */ ENABLE_ALL_IT; PCA_ON; do{ }while(nb_it<=tocount); /* wait motor turn nb_loop */ PCA_OFF; P1 = P_LOW; /* clear all coils (no comsumption) */ do{ }while(1); /* endless */ } 4214B–8051–12/02 Printed on recycled paper. ATMEL® is a registered trademark of Atmel. Other terms and product names may be the trademarks of others. © Atmel Corporation 2002. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. Atmel Headquarters Atmel Operations Corporate Headquarters 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 487-2600 Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 Memory 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 2-40-18-18-18 FAX (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-42-53-60-00 FAX (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland TEL (44) 1355-803-000 FAX (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany TEL (49) 71-31-67-0 FAX (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Data- com Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-76-58-30-00 FAX (33) 4-76-58-34-80 e-mail literature@atmel.com Web Site http://www.atmel.com 4214B–8051–12/02 /xM Introduction Description Identification of Stepper Motor Unipolar Stepper Motor Bipolar Stepper Motor Variable Reluctance Driving Unipolar Stepper Motors One Phase On Mode (Full Step mode) Two Phases On Mode (Alternate Full step Mode) Half Step Mode Hardware Driving Two Stepper Motors with Only One PCA Software Appendix A: Software MAIN.C