SM331 INFORMATION COLLECTION
SLC A&D CS
April 2004
SM331 Information Collection
SLC A&D CS Page 2 of 15
1. 如何获得西门子自动化与驱动产品的资料及在线技术支持 .......................3
2. 西门子技术支持热线 ................................................................................3
3. 需要 SM331 的产品手册 ..........................................................................3
4.
标准
excel标准偏差excel标准偏差函数exl标准差函数国标检验抽样标准表免费下载红头文件格式标准下载
及认证...............................................................................................3
5. SM331 搬运、存储、运行的环境要求 ......................................................3
6. SM331 常用信息 ......................................................................................3
7. 缩写词含义...............................................................................................3
8. 如何使用 SM331 ......................................................................................3
9. 在 STEP 7 的硬件目录里找不到想要配置的硬件......................................3
10. SM331 上不使用的通道的接线.................................................................3
11. 如何在 STEP 7 中设置 SM331 的参数并访问其通道................................3
11.1. 如何在 HW Config 中设置 SM331 的参数 .................................................... 3
11.2. 在程序中对模拟量输入的访问 ...................................................................... 3
12. 如何连接传感器及外部电源到 SM331
模板
个人简介word模板免费下载关于员工迟到处罚通告模板康奈尔office模板下载康奈尔 笔记本 模板 下载软件方案模板免费下载
..............................................3
13. 连接二线制变送器到 SM331 模板 ............................................................3
13.1. 两线制信号(2DMU)与四线制信号(4DMU)的区别 ......................................... 3
13.2. 如何连接两线制变送器到只能接入四线制信号的模板 .................................. 3
13.3. 两线制信号与四线制信号接线的注意事项 .................................................... 3
13.4. 不同类型传感器到 SM331-7Kx0x 的接线实例 .............................................. 3
14. 连接热电偶到 SM331 模板 .......................................................................3
14.1. 为什么要用补偿盒对 SM331 进行外部冷端补偿及怎样补偿(6ES7
331-7KFxx-0AB0 及 6ES7 331-7KBxx-0AB0) ............................................................... 3
14.2. 热电偶量程转换 ........................................................................................... 3
15. 连接热电阻到 SM331 模板 .......................................................................3
15.1. 热电阻测量原理及连接两线、三线、四线热电阻到 6ES7 331-7Kxxx-0AB0 3
15.2. 量程转换 ...................................................................................................... 3
SM331 Information Collection
SLC A&D CS Page 3 of 15
15.3. 为什么用数字万用
表
关于同志近三年现实表现材料材料类招标技术评分表图表与交易pdf视力表打印pdf用图表说话 pdf
测量不到 SM331 模板测量电阻值的电流 ..................... 3
请点击 http://www4.ad.siemens.de/WW/view/en/13963555 阅读在线 FAQ。 .............. 3
15.4. 连接三线制热电阻到 6ES7331-7PF00-0AB0 的注意事项 ............................ 3
16. 连接 HART 协议仪表到 SM331 模板........................................................3
16.1. 如何连接支持 HART 协议的仪表到 SM331 模板 .......................................... 3
16.2. 怎样用 SM331(6ES7331-7TB00-0AB0)读 HART 仪表的数据 ..... 3
16.3. 连接 HART 仪表到常规 S7-300 模拟量输入模板 ........................................ 3
16.4. 6ES7331-7TB00-0AB0 不用通道的设置 ................................................ 3
17. 怎样设置并修改 SM331 的分辨率 ............................................................3
18. STEP 7 中用于读取模拟量的功能块........................................................3
19. 读出的模拟量值超限 ................................................................................3
20. SM331 SF 灯亮........................................................................................3
21. 直接将来自 0 区或 1 区的传感器信号接入 S7-300 Ex(i) 模板..................3
22. 与 SM331 有关的 OB 块 ..........................................................................3
SM331 Information Collection
SLC A&D CS Page 4 of 15
1. 如何获得西门子自动化与驱动产品的资料及在线技术支
持
首先,建议您访问 Siemens A&D 的产品与技术支持网站 http://www4.ad.siemens.de/
或者,致电 010-64721888 转 3785 索取资料。
如需设备选型及订货,请联系当地西门子分销商。分销商联系方式可致电 010-64719990
获得。
2. 西门子技术支持热线
如有无法自行解决的技术问
题
快递公司问题件快递公司问题件货款处理关于圆的周长面积重点题型关于解方程组的题及答案关于南海问题
,请拨打西门子技术支持热线 010-64719990 登记,等待西
门子技术支持工程师回复。我们会在 8 小时内予以响应。
请注意在登记问题时尽量准确地描述所使用产品的类型,以便尽快得到负责该产品的
工程师的帮助。
SM331 Information Collection
SLC A&D CS Page 5 of 15
3. 需要 SM331 的产品手册
请点击 http://www4.ad.siemens.de/WW/view/en/8859629 下载。
4. 标准及认证
1. CE approval
2. UL approval
3. CSA approval
4. FM approval
5.
6. Identification for Australia
7. IEC 61131
8. Shipbuilding approval
详细信息请参见模板手册。
5. SM331 搬运、存储、运行的环境要求
标准模板运行状况下要求的气候条件参见下表:
SIPLUS S7-300 模板应用于扩展的环境条件下,扩展的环境条件描述如下:
• Operation possible at temperatures from –25°C to +60°C
SM331 Information Collection
SLC A&D CS Page 6 of 15
• Occasional, brief condensation permitted
• Increased mechanical stress permissible
详细信息请参见模板手册。
6. SM331 常用信息
SM331 模板是西门子 S7-300 系列 PLC 中的模拟量输入模块,常用模板的信息请参见
"SM331
Characteristics"
7. 缩写词含义
FAQ: Frequently Asked Questions 经常问到的问题
M +: Measuring lead (positive) 信号线(正)
M–: Measuring lead (negative) 信号线(负)
MANA: Reference potential of the analog measuring circuit 模拟量输入回路的参考电势
M: Ground terminal 接地端
L +: Terminal for 24 VDC supply voltage 24VDC电源接线端
UCM: Potential difference between inputs and reference potential of the MANA measuring circuit
信号输入端与MANA间的电势差
UISO: Potential difference between MANA and M terminal of CPU MANA与CPU的M端间的电势
差
I +: Measuring lead for current input 电流输入测量端
U +: Measuring lead for voltage input 电压输入测量端
8. 如何使用 SM331
请点击 http://www4.ad.siemens.de/WW/view/en/17473828 下载 Getting Started of SM331
4~20mA 手册。
使用 SM331 的基本步骤如下:
1. Select the module 模板选型
SM331 Information Collection
SLC A&D CS Page 7 of 15
2. With some analog input modules: set the measuring method and measuring range by
means of the measuring range module 通过量程卡确定测量类型、测量范围
3. Install the module in the SIMATIC S7 network 安装模板
4. Assign parameters to module 设置参数
5. Connect measuring sensor or loads to module 连接传感器到模板
6. Commission configuration 调试
7. If commissioning was not successful, diagnose configuration 如调试出错,做相应的诊
断
9. 在 STEP 7 的硬件目录里找不到想要配置的硬件
如果在 STEP 7 的硬件目录中找不到想要配置的硬件,解决
办法
鲁班奖评选办法下载鲁班奖评选办法下载鲁班奖评选办法下载企业年金办法下载企业年金办法下载
如下:
1. Installing Hardware Updates
As of STEP 7 V5.2, you can subsequently install components for the Hardware Catalog. In this
way you can use individual components such as new CPUs or new I/O devices in the current
version of STEP 7 without having to install a new service pack.
Procedure:
¾ Select the menu command Options > Install HW Updates.
¾ In the dialog that appears, specify whether the HW update should be downloaded from
the Internet or copied from a CD or
whether you want to install updates that have already been download (selection
available)
¾ Select the component to be installed and then click the "Install" button.
2. 如果您使用的是 STEP 7 V5.1 或者更低的版本,而在 STEP 7 的硬件目录里找不到
想要配置的硬件,那么首先建议您到 http://www4.ad.siemens.de 网站上下载 STEP 7
的补丁程序,如 SP6 for STEP 7 V5.1 或 SP1 for STEP 7 V5.2 并安装,如果仍然找不
到想要配置的硬件,就必须找当地的分销商升级 STEP 7 软件到最新的版本。目前
STEP 7 的最新版本为 V5.3。
SM331 Information Collection
SLC A&D CS Page 8 of 15
10. SM331 上不使用的通道的接线
请点击 http://www4.ad.siemens.de/dnl/DkxODg4MQAA_42382/besch_e.pdf 了解详细信息。
或参考下文:
"unused channel
wiring" 。
11. 如何在 STEP 7 中设置 SM331 的参数并访问其通道
11.1. 如何在 HW Config 中设置 SM331 的参数
通常,在硬件配置中 SM331 的属性设置包括 General, Addresses, Inputs 三项,见下图:
在 General 中包含对模板信息的描述。在 Addresses 中定义该模板各通道在系统中的 I/O 地
址,在程序中可以用 PIW 的方式访问,如 PIW218。在 Inputs 中包含诊断中断、硬件中断、
断线检测、测量类型、测量范围、量程卡等的相关设置与信息,详细描述请点击右下角 Help
键。
SM331 Information Collection
SLC A&D CS Page 9 of 15
其中一个参数需要注意:
Integration Time/ interference frequency suppression
The frequency of the AC power supply network can interfere with the measurement values. With
this parameter you specify the frequency of your power supply on site.
• Interference frequency: Select your power frequency (50 Hz or 60 Hz)
The integration time implicitly determines:
· The interference frequency suppression
· The resolution
The following table illustrates this relationship:
11.2. 在程序中对模拟量输入的访问
在程序中对模拟量输入的访问分为直接地址及过程映像两种。直接地址即直接访问在 HW
Config 中定义的地址,如该通道地址为 120,则在程序中访问 PIW120(PI: Peripheral Input)
即可。过程映像则是在程序中直接访问 CPU 的 process image,如该通道地址为 120,则在
程序中访问 IW336 即可。两者差别如下:
Compared with direct access to the input/output modules, the main advantage of accessing the
process image is that the CPU has a consistent image of the process signals for the duration of
one program cycle. If a signal state on an input module changes while the program is being
executed, the signal state in the process image is retained until the process image is updated
again in the next cycle. The process of repeatedly scanning an input signal within a user program
ensures that consistent input information is always available.
Access to the process image also requires far less time than direct access to the signal modules
since the process image is located in the internal memory of the CPU.
SM331 Information Collection
SLC A&D CS Page 10 of 15
12. 如何连接传感器及外部电源到 SM331 模板
请参见模板手册中相应订货号的模板的外部接线图。
13. 连接二线制变送器到 SM331 模板
13.1. 两线制信号(2DMU)与四线制信号(4DMU)的区别
参见
2线制传感器和4线
制传感器说明FAQ
或点击 http://www4.ad.siemens.de/WW/view/en/188821 阅读在线 FAQ。
13.2. 如何连接两线制变送器到只能接入四线制信号的模板
请点击 http://www4.ad.siemens.de/WW/view/en/18475312 阅读在线 FAQ。
13.3. 两线制信号与四线制信号接线的注意事项
2-wire measuring transducer:
• Connect Mana to M (jumper between Pins 11 and 20) and jumper Pins 10 and 11.
• Short-circuit the unused channels of a channel group or jumper them with a 3.3 kohm
resistor.
4-wire measuring transducer:
• Connect all Mx- to Mana and Pin 10 to Pin 11.
• Connect the unused channels of a channel group in series and connect Mx- to Mana.
13.4. 不同类型传感器到 SM331-7Kx0x 的接线实例
请点击 http://www4.ad.siemens.de/WW/view/en/264773 阅读在线 FAQ。
SM331 Information Collection
SLC A&D CS Page 11 of 15
14. 连接热电偶到 SM331 模板
14.1. 为什么要用补偿盒对 SM331 进行外部冷端补偿及怎样补偿(6ES7
331-7KFxx-0AB0 及 6ES7 331-7KBxx-0AB0)
请点击 http://www4.ad.siemens.de/WW/view/en/18272332 阅读在线 FAQ。
14.2. 热电偶量程转换
各分度的热电偶量程转换表,请参见模板手册。
15. 连接热电阻到 SM331 模板
15.1. 热电阻测量原理及连接两线、三线、四线热电阻到 6ES7 331-7Kxxx-0AB0
请点击 http://www4.ad.siemens.de/WW/view/en/8460832 阅读在线 FAQ。
15.2. 量程转换
各分度的热电阻量程转换表,请参见模板手册。
常用的 PT100 热电阻量程转换表如下:
SM331 Information Collection
SLC A&D CS Page 12 of 15
本文仅列出常用的 Pt 电阻的量程转换表,如果使用 Cu 电阻或 Ni 电阻,请参见模板手册。
15.3. 为什么用数字万用表测量不到 SM331 模板测量电阻值的电流
请点击 http://www4.ad.siemens.de/WW/view/en/13963555 阅读在线 FAQ。
15.4. 连接三线制热电阻到 6ES7331-7PF00-0AB0 的注意事项
在连接三线制热电阻到 6ES7331-7PF00-0AB0 这块模板时有一个注意事项,在模板手册中
有一条说明:The resistance measurement for a three-conductor connection is performed every 5
minutes。也就是说,在三线制热电阻接入这块模板时,第一次从模板读到数据需要 5 分钟
的时间,因为模板每 5 分钟计算一次热电阻的长线补偿值。
16. 连接 HART 协议仪表到 SM331 模板
16.1. 如何连接支持 HART 协议的仪表到 SM331 模板
"HART Config for
S7-300/400"
SM331 Information Collection
SLC A&D CS Page 13 of 15
16.2. 怎样用 SM331(6ES7331-7TB00-0AB0)读 HART 仪表的数据
怎样读HART仪表的
数据
16.3. 连接 HART 仪表到常规 S7-300 模拟量输入模板
请点击 http://www4.ad.siemens.de/WW/view/en/2043180 阅读在线 FAQ。
16.4. 6ES7331-7TB00-0AB0 不用通道的设置
请点击 http://www4.ad.siemens.de/WW/view/en/14034159 阅读在线 FAQ。
17. 怎样设置并修改 SM331 的分辨率
请点击 http://www4.ad.siemens.de/WW/view/en/42510 阅读在线 FAQ。
18. STEP 7 中用于读取模拟量的功能块
You can use the blocks FC 105 “SCALE” (Scale Values) for reading analog values in STEP 7.
You will find the FC in the standard library of STEP 7 in the subdirectory called “TI-S7
Converting Blocks” (for a description, refer to the STEP 7 Online Help for the FC).
19. 读出的模拟量值超限
请点击 http://www4.ad.siemens.de/WW/view/en/11966082 阅读在线 FAQ。
通常,从 SM331 的通道中读出 7FFF 超限值的现象可以通过正确的外部接线避免,各种信
号及各订货号模板的接线参见本文相关章节。如果在外部接线完全满足模板要求的情况下,
仍然出现读数超限,则有可能是信号源接地不好、信号电缆敷设过程中有电磁干扰等原因
造成 M-与 Mana 间电势差 Ucm 过大。这种情况下建议采用有源信号隔离器。
20. SM331 SF 灯亮
SM331 SF 灯亮表明硬件故障。可能的原因如下:模板所需 24VDC 电源未正确接入;前连
接器未插到位;总线连接器未连好;有硬件中断产生(断线、超限),量程卡所插的方向与
SM331 Information Collection
SLC A&D CS Page 14 of 15
HW Config 中的设置不符,等等。
在线察看模板信息的方法参见下图:
21. 直接将来自 0 区或 1 区的传感器信号接入 S7-300
Ex(i) 模板
请点击 http://www4.ad.siemens.de/WW/view/en/12346645 阅读在线 FAQ。
22. 与 SM331 有关的 OB 块
Type of
Interrupt
Organization Block Priority Class
(Default)
See also (STEP 7 Online Help)
Main program
scan
OB1 1 Organization Block for Cyclic Program
Processing (OB1)
Cyclic
interrupts
OB30
OB31
OB32
OB33
OB34
OB35
7
8
9
10
11
12
Cyclic Interrupt Organization Blocks
(OB30 to OB38)
SM331 Information Collection
SLC A&D CS Page 15 of 15
OB36
OB37
OB38
13
14
15
Hardware
interrupts
OB40
OB41
OB42
OB43
OB44
OB45
OB46
OB47
16
17
18
19
20
21
22
23
Hardware Interrupt Organization Blocks
(OB40 to OB47)
Redundancy
errors
OB70 I/O Redundancy
Error (only in H
systems)
OB72 CPU
Redundancy Error
(only in H systems)
25
28
"Error Handling Organization Blocks
(OB70 to OB87 / OB121 to OB122)"
Asynchronous
errors
OB80 Time Error
OB81 Power Supply
Error
OB82 Diagnostic
Interrupt
OB83 Insert/Remove
Module Interrupt
OB84 CPU Hardware
Fault
OB 85 Program Cycle
Error
OB86 Rack Failure
OB87 Communication
Error
25
(or 28 if the
asynchronous
error OB
exists in the
startup
program)
Error Handling Organization Blocks
(OB70 to OB87 / OB121 to OB122)
Startup OB100 Restart
(Warm start)
OB101 Hot Restart
OB102 Cold Restart
27
27
27
Startup Organization Blocks
(OB100/OB101/OB102)
Synchronous
errors
OB121 Programming
Error
OB122 Access Error
Priority of the
OB that
caused the
error
Error Handling Organization Blocks
(OB70 to OB87 / OB121 to OB122)
各 OB 块详细信息请参见 STEP 7 在线帮助。具体方法为:打开 STEP 7 Help, 在 Index 中搜
索关键字 OBxx,即可查到该块的功能、可访问的临时变量等。