首页 SRD991智能定位器使用手册

SRD991智能定位器使用手册

举报
开通vip

SRD991智能定位器使用手册 快速指导 12.06 QG EVE0105 B1-(int) SRD991 型智能阀门定位器 快速指导…. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (中文版) Quick Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Eng...

SRD991智能定位器使用手册
快速指导 12.06 QG EVE0105 B1-(int) SRD991 型智能阀门定位器 快速指导…. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (中文版) Quick Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(English) SRD991 QG EVE0105 B1-(int) Quick Guide 12.2006 QG EVE0105 B-(chi) SRD991型智能阀门定位器 此说明书是用于使定位器快速启动的指导。如果需要更多具体的信息,请参见 标准 excel标准偏差excel标准偏差函数exl标准差函数国标检验抽样标准表免费下载红头文件格式标准下载 文件“主说明书”和 “产品规格单”。这些文件可以在我公司的网站 www.foxboro-eckardt.com找到。 带有 LCD的型号(和 LEDs): SRD991 –HART, -PA, -FF, FoxCom 仅带有 LEDs:的型号 SRD991 - 所有类型– 1. 安装到执行机构上 在操作中,在定位器背后的轴 9的平面必须总是面向箭头 26。围绕此方向的操作角度是 45º。 � � � � � � 2 SRD991 QG EVE0105 B-(chi) 安装到线形执行机构上 NAMUR安装 – 左手位置 - NAMUR 安装 –右手位置 - 用于线形执行机构的反馈杆: 直接安装 承载螺栓 B在反馈杆 A的长孔之中,并且补偿弹 簧要接触到承载螺栓。 �� � 承载螺栓 B: 1 螺套 2 柱头螺栓 3 接合件 � � � � � 安装到角行程执行机构上 •不要将埋头螺钉 4与轴 9的螺纹拧紧。 •当在使用中,轴 9的平面必须在箭头 26的前面 移动( 0 ↔ 100%)。 • 当产品的温度上升时,传动轴 1的长度增加。 因此,必须安装旋转适配器 3,以便于在传动轴 1和旋转适配器 3之间留有大约 1mm(0.04in.)的 间隙。在安装旋转适配器之前,通过在反馈杆 9 上加上适当数量的垫圈 5来实现此目的。2个垫 圈可形成 1mm的间隙。 QG EVE0105 B-(chi) SRD991 3 执行机构, 向左旋转 执行机构, 向右旋转 � � � � � � � � 2. 连接 在安装配件和电缆密封管之前检查螺纹是否匹 配,如果不匹配,外壳会被损坏。在外壳上的字 母“G” 关于同志近三年现实表现材料材料类招标技术评分表图表与交易pdf视力表打印pdf用图表说话 pdf 明气动接头是 G1/4(其他的是 NPT)。 接地 将接地电缆与螺钉#1或#2连接(在电动连接部 位) � � � � � � � 气动连接 气源:1.4 to 6 bar(但不能大于执行机构的最大压力),无油、灰尘和水! � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 单作用, 直接安装 单作用 双作用 s 气源 y1, y2 气动输出 (--) 关闭 4 SRD991 QG EVE0105 B-(chi) 3. 电动连接 必须遵守文件 EX EVE0001的安全要求和 PSS EVE0105文件和MI EVE0105 for SRD991文件中的要求! 3.2 感应限位开关 SRD991-xxxT or U 遵照 DIN 19234 or NAMUR的两线 制传感器 供给电压 DC 8 V 带有本安控制电路的开关 放大器 带有本安控制电路的开关 放大器 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � SRD991-xxxV 警告: 对于连接微动开关,请参见主 说明书并参考在文件 EX EVE0001中 所描述的安全要求。 3.1 设定点 3.3 可选电路板 对于 SRD991-xD (w/o 通讯) 对于 SRD991-xH (HART) 对于 SRD991-xE (FoxCom it1) 二进制输出 (SRD991-xxP) 两线制, 遵照 DIN 19234 供给电压 DC 8 to 48 V* � � � � � � � � � � � � � � � � � 输入 4 to 20 mA 带有本安控制电路的开关放大器 对于 SRD991-xF (FoxCom it2) � � � � � � � � � � � � � � 带有本安控制电路的开关放大器 � � � � � � � � � � � � � � � � � 供给电压 DC 13 to 48 V * 二进制输入 (SRD991-xxB) 内部供给的二进制输入用于连接传感器或开关 (用于正常操作的开关关闭!) 对于 SRD991-xP (PROFIBUS-PA) 对于 SRD991-xQ (FOUNDATION F. H1) � � � � � � � � � � � � � � � � � � � � � � � � 位置反馈 4 to 20 mA 和 1 个警报器 (SRD991-xxQ) 遵照 IEC 1158-2的总线连接 供给电压 DC 9 to 32 V* 4 to 20 mA模拟输出, 两线制, 供应电压 DC 8 to 48 V* � � � � � � � � � � � � � � � 带有本安控制电路的开关放大器 *.对于本安电路,请参照认证/最大操作压力的数据标 签等等。 QG EVE0105 B-(chi) SRD991 5 4. 启动 (通过现场按键和 LCD / LEDs的方式设定) 在定位器安装到执行机构、气源以及电输入连接完成后,您就可以开启 SRD型定位器了。 注意:在按键操作过程中,请勿接触定位器外壳后面!有受伤危险! 显示描述 按键 过程参数 87.5 % Valve position 过程参数和诊断 87.5 % Valve position Ctrl diff error (M) 进入或退 出主菜单 (向下) 上一个菜 单或参数 (上) 下一个菜 单或参数 |-两个同时按下:-| 在组态中: 主菜单 进入 / 存储 SRD Main Menu 1 Mounting 2 Autostart 3 Valve Action 在组态中,被选项目加深背景显示。 显示更多菜单需按(向上)键。 通过按键来组态和操作 通过 LCD显示: 通过 LED显示 已组态的设备会有如下显示: 在开启后,一个已组态的设备在运转中,所有 LEDs指示灯将熄灭。 87.5 % Valve position 如组态,请按(M)键,主菜单将显示出来。 如果 SRD定位器还没有被组态,主菜单*)将在开 启后自动显示出来: 如组态,请按(M)键,LEDs指示灯‘M/F’和‘1’将 闪烁。(=菜单 1被提供出来) 如果 SRDD定位器还没有被组态,菜单 1将在开 启后自动提供出来: SRD Main Menu 1 Mounting 2 Autostart 3 Valve Action 在菜单 1中,您可以选择安装方式。 在菜单 1中,您可以选择安装方式。 *) 交付使用时,显示的菜单语言为英语。 菜单语言可以改变成其他存储的语言。为此,可 选择 9.8.2 [德语] 或 9.8.3 [根据订单],并通过 (向上)+(向 下)键(同时)按下来确定。 通过重复按(M)键来离开菜单。 6 SRD991 QG EVE0105 B-(chi) ... LCD显示: ... LED显示: 同时按(向上)+(向下)键进入‘安装方式’菜单。通过按(向上)或(向下)键选择‘安装方式’。 线形执行机构,左手方 向安装。 1 Mounting 1.1 Lin left 1.2 Lin right 1.3 rot cclockw 线形执行机构,右手方 向安装。 角行程执行机构,逆时 针开启 (更多菜单请按(向上)键。) 角行程执行机构,顺时 针开启 同时按(向上)+(向下)键来确定并保存。 SRD定位器将回到第 1级菜单并再次进入主菜单。 SRD Main Menu 1 Mounting 2 Autostart 3 Valve Action 进入下一个菜单(=菜单 2,自动启动) 按(向上)键一次。 进入下一个菜单(=菜单 2,自动启动) 按(向上)键一次,LEDs ‘M’ 和 ‘2’指示灯将闪 烁。 SRD Main Menu 1 Mounting 2 Autostart 3 Valve Action 同时按(向上)+(向下)键进入‘自动开启’菜单。通过按(向上)或(向下)键选择全部或短时间自动 启动。 全部自动启动 2 Autostart 2.1 Endpoints 2.2 Standard 2.3 Enhanced 可选择的不同的自动启动: 2.1 终点 只决定执行机构/阀门的机械停止 2.2 标准 被推荐的自动开启,用于标准应用。 2.3 增强的 增强的自动启动。与标准自动启动相比,控制动作被优化。 2.4 平稳 延长的自动开启. 衰减的控制动作,例如较小的执行机构。 2.5 快速 延长的自动开启. 非衰减的控制动作,例如较大的执行机构。 同时按(向上)+(向下)键来确定并执行自动开启。 自动适用到阀门上由一系列的步骤组成,在LCD上说明或通过LEDs指示。 在最后一步完成后,设备进入运转状态。 QG EVE0105 B-(chi) SRD991 7 带有LCD的SRD991/SRD960定位器的菜单结构 SRD主菜单 Menu 工厂 描述 组态 1 Mounting 安装 1.1 Lin left 9 线形执行机构, 左手方向或直接安装 1.2 Lin right 线形执行机构, 右手方向安装 1.3 Rot cclockw 角行程执行机构, 逆时针方向开启 1.4 Rot clockw 角行程执行机构, 顺时针方向开启 2 Autostart 自动开启 2.1 Endpoints 只适合机械停止 2.2 Standard 推荐的自动开启,标准应用 2.3 Extended 延长的自动开启,快速响应并可能过度动作 2.4 Smooth resp. 延长的自动开启, 衰减响应以避免过度动作 2.5 Fast resp. 延长的自动开启,非常快速的响应并限制过度动作 3 Valve Action 阀门动作 3.1 Direct 9 阀门开启,设定点值递增 3.2 Reverse 阀门关闭,设定点值递增 4 Character 特性 4.1 Linear 9 线形特性 4.2 Eq Perc 1:50 等比特性 1:50 4.3 Quick open 反转等比特性 1:50 (快开) 4.4 Customer 自定义特性 5 Limits/alarms 不能在现场使用具有FF和Profibus通讯的 LED型 5.1 Lower limit 0 % 设定关闭限制的输入值 5.2 Cutoff low 1 % 设定0%-紧密封点输入值 5.3 Cutoff high 100 % 设定100%-紧密封点输入值 5.4 Upper limit 100 % 设定开启限制的输入值 5.5 Splitr 0 % 4 mA 分程 0 %: 输入值对应 0 % 5.6 Splitr 100 % 20 mA 分程 100 %: 输入值对应 100 % 5.7 Lower Alarm -10 % 为输出1低位报警设定输入值 5.8 Upper Alarm 110 % 为输出2高位报警设定输入值 5.9 Valve 0% 4 mA 组态在4mA时额定行程为0% 5.10 Valve 100% 20 mA 组态在20 mA时额定行程为100% 5.11 Stroke Range x° / 20mm 公称行程组态 5.12 Temp unit °C 温度单位为°C or °F的组态 6 Parameters 参数 6.1 Gain closing 15 P: 用于'关阀'的比例增益 6.2 Gain closing 2 P: 用于'开阀'的比例增益 6.3 Res time cl 7.5 I: 用于'关阀'的整体时间 6.4 Res time op 2.4 I: 用于'开阀'的整体时间 6.5 Rate lim cl 0.35 T63:设定'关阀'的时间 6.6 Rate lim op 0.35 T63:设定'开阀'的时间 6.7 Control gap 0.1 可允许的中性区用于控制差异 7 Output 手动设置IP-模块用于测试气动输出 8 Setpoint 手动设置阀位 8.1 12.5% Steps 通过使用向上或向下按键使设定点每步变化12.5% 8.2 1% Steps 通过使用向上或向下键使设定点每步变化1% 下一页继续... 8 SRD991 QG EVE0105 B-(chi) 8.2 12.5% Steps Setpoint springs of 12.5% at each druck on Up or Down 8.2 1% Steps Setpoint springs of 1% at each druck on Up or Down 9 Workbench 9.1 Reset Config Resetting of configuration to setting “ex factory” 9.2 Calib. 4 mA Calibrate input current to 4 mA 9.3 Calib. 20 mA Calibrate input current to 20 mA 9.4 Calib. -45° Calibrate position measuring value to –45° 9.5 Calib. +45° Calibrate position measuring value to +45° 9.6 Reset all 1 Resetting of configuration and Calibration (!) to “ex factory” setting for single-acting output 9.7 Reset all 2 Resetting of configuration and Calibration (!) to “ex factory” setting for double-acting output 9.8 Menu Lang 9.8.1 English 9 Standard 9.8.2 Deutsch Standard 9.8.3 Français Preselected / Freely Defiable 9.9 LCD orient 9.9.1 Normal 9 Normal orientation of writing on LCD 9.9.2 Flipped Reverse orientation of writing on LCD 9.10 Cal. Feedbk Calibration of output current of position transmitter 9.10.1 Cal 4mA Calibration of 0% at 4mA 9.10.2 Cal. 20mA Calibration of 100% at 20mA 10 - not available - for HART 10 Profibus PA - Bus Address 10.1 Address LSB Ratio from Dec. 0 / Hex 00 to Dec. 15 / Hex 0F 10.2 Address MSB Ration from Dec. 0 / Hex 00 to Dec. 112 / Hex 70 10.3 Address 126 Display of Bus Address from Dec. 1 to 127 (Hex 00 to 7F) 10 FOUNDATION Fieldbus H1 10.1 Simulate Disabled 9 Simulate disabled Enabled Simulate enabled 10.2 Profile A此产品的附加文件: 定位器连接件的技术信息 TI EVE0011 A 定位器安装在不同制造商的执行机构/阀门的连接件的综述 快速指导 QG EVE0105 A 主说明书的摘录,使用简单,容易理解且可快速开始使用产品。此文 件突出了说明书中最重要的内容。 主说明书: MI EVE0105 A SRD991型智能阀门定位器 用于其他产品的附加文件: 产品规格 PSS EVE0109 A-(en) SRD960 通用阀门定位器 PSS EVE0105 A-(en) SRD991 智能阀门定位器 PSS EVE0107 A-(en) SRI990 模拟阀门定位器 PSS EVE0103 A-(en) SRI983 电气阀门定位器- 防爆或 EEx d 型 PSS EVE0102 A-(en) SRI986 电气阀门定位器 PSS EVE0101 A-(en) SRP981气动阀门定位器 Quick Guide 08.2004 QG EVE0105-(en) SRD991 Intelligent Positioner These instructions are to be used as a guide for quick start-up. For more detailed information please refer to the standard documents “Master Instructions” and “Product Specification Sheet”. These can be found on our Website www.foxboro-eckardt.com Versions with LCD (and LEDs): SRD991 –HART, -PA, FF Versions with only LEDs: SRD991 - all versions - 1. MOUNTING TO ACTUATORS During operation the flat side of the spindle 9 on the back of the positioner must always point towards the arrow 26. The working angle around this position is ±45º. � � � � � � 2 SRD991 QG EVE0105-(en) MOUNTING TO LINEAR ACTUATORS NAMUR Mounting - left hand - NAMUR Mounting - right hand - Feedback lever for linear actuators : Direct Mounting The carrier bolt B is in the slot of the feedback lever A and the compensating spring F touches the carrier bolt. �� � Carrier bolt B: 1 threaded sleeve 2 Stud 3 coupling piece � � � � � MOUNTING TO ROTARY ACTUATORS • Do not tighten grub screw 4 against the thread of spindle 9 ! • When in use the flat side of the spindle 9 must move ( 0 ↔ 100%) in front of the arrow 26. • When the product temperature rises, the drive shaft 1 increases in length. Therefore, the rotary adapter 3 must be mounted so that approx. 1 mm (0.04 in.) of clearance results between the drive shaft 1 and the rotary adapter 3. This is achieved by placing an appropriate number of washers 5, on the feedback spindle 9, before attaching the rotary adapter. Two washers should result in a clearance of 1 mm. QG EVE0105 (en) SRD991 3 Actuator, left turning Actuator, right turning � � � � � � � � 2. CONNECTIONS Check before mounting fittings and cable glands if threads are matching, otherwise housing can be damaged. The letter “G” on the housings marks that the pneumatic connections are in G1/4 (otherwise NPT). Ground Connect earth cable to screw #1 or screw #2 (in the electrical connection compartment). � � � � � � � PNEUMATIC CONNECTIONS Air supply (s): 1.4 to 6 bar (but not more than the max. pressure of actuator), free of oil, dust and water ! � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � Single acting, Direct mounting Single acting Double acting s supply y1, y2 pneumatic outputs (--) closed 4 SRD991 QG EVE0105-(en) 3. ELECTRICAL CONNECTIONS The safety requirements of document EX EVE0001 as well as the requirements of PSS EVE0105 and MI EVE0105 for SRD991 must be observed! 3.2 Inductive Limit Switch SRD991-xxxT or U Two-wire proximity sensors, Acc. to DIN 19234 or NAMUR Supply voltage DC 8 V Switching amplifier with intrinsically safe control circuit Switching amplifier with intrinsically safe control circuit � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � SRD991-xxxV Warning: For connection of micro switches please refer to MI (Master Instruction) and respect the safety requirements described in document EX EVE0001. 3.1 Setpoint 3.3 Option Board For SRD991-xD (w/o communication) For SRD991-xH (HART) For SRD991-xE (FoxCom it1) Two binary outputs (SRD991-xxP) Two-wire system, acc. to DIN 19234 Supply voltage DC 8 to 48 V* � � � � � � � � � � � � � � � � � Input 4 to 20 mA Switching amplifier with intrinsically safe control circuit For SRD991-xF (FoxCom it2) � � � � � � � � � � � � � � Switching amplifier with intrinsically safe control circuit � � � � � � � � � � � � � � � � � Supply voltage DC 13 to 48 V * Two binary inputs (SRD991-xxB) Binary inputs with internal supply for connection of sensors or switches (switch closed for a normal operation!) For SRD991-xP (PROFIBUS-PA) For SRD991-xQ (FOUNDATION F. H1) � � � � � � � � � � � � � � � � � � � � � � � � Position feedback 4 to 20 mA and 1 Alarm (SRD991-xxQ) Bus connection acc. to IEC 1158-2 Supply voltage DC 9 to 32 V* Analog output 4 to 20 mA, Two-wire system, Supply voltage DC 8 to 48 V* � � � � � � � � � � � � � � � Switching amplifier with intrinsically safe control circuit * For intrinsically safe circuits please refer to certi- ficate / data label for max. operating voltages etc. QG EVE0105 (en) SRD991 5 4. START UP (Setting by means of local keys and LCD / LEDs) After mounting the positioner on the actuator, air and electrical input connected, you can start-up the SRD. The SRD991 can be adjusted by means of a local key-pad and LCD / LED display. Attention: Do not touch behind the positioner housing while operating the keys! DANGER OF INJURIES! Description of display Push buttons Process variable 87.5 % Valve position Process variable and diagnostics 87.5 % Valve position Ctrl diff error (M) Enter or exit main menu (DOWN) Previous menu or Parameter (UP) Next menu or Parameter |-both simultaneously:-| At configuration: Main menu Enter / store SRD Main Menu 1 Mounting 2 Autostart 3 Valve Action At configuration the selected item is displayed with dark background. Further menus with (UP) key. Configuration and operation with push buttons and LCD: and LED display: An already configurated device may show the following display: An already configurated device is IN OPERATION after power up, and all LEDs are off. 87.5 % Valve position For configuration press (M) and main menu appears. If the SRD wasn’t configurated yet, the Main menu*) appears automatically after power-up: For configuration press (M), and LEDs ‘M/F’ and ‘1’ flash (= menu 1 is offered). If the SRD wasn’t configurated yet, menu 1 is offered automatically after power-up: SRD Main Menu 1 Mounting 2 Autostart 3 Valve Action In menu 1 you can select the type of mounting. In menu 1 you can select the type of mounting. *) On delivery the menu language in the display is English. The menu language can be changed over to another stored language. For this select 9.8.2 [german] or 9.8.3 [as ordered] and confirm with keys (UP)+(DOWN) (simultaneously). Leave menu by repeated pressing of (M) key. 6 SRD991 QG EVE0105-(en) ... and LCD: ... and LED display: Press keys (UP)+(DOWN) simultaneously to enter menu ‘Type of mounting’. Select the ‘Type of mounting’ by pressing (UP) or (DOWN). Press keys (UP)+(DOWN) simultaneously to enter menu ‘Type of mounting’. Select the ‘Type of mounting’ by pressing (UP) or (DOWN). Lin.actuator, left-hand mount. 1 Mounting 1.1 Lin left 1.2 Lin right 1.3 rot cclockw Lin.actuator, right-hand mount. Rotary actuator, opening ccw (Further menus with (UP) key.) Rotary actuator, opening cw Press keys (UP)+(DOWN) simultaneously to confirm and save. The SRD moves back to menu level 1 and is in main menu again. Press keys (UP)+(DOWN) simultaneously to confirm and save. The SRD moves back to menu level 1 and is in main menu again. SRD Main Menu 1 Mounting 2 Autostart 3 Valve Action To enter next menu (= menu 2, AUTOSTART) press (UP) once. To enter next menu (= menu 2, AUTOSTART) press (UP) once, and the LEDs ‘M’ and ‘2’ flash. SRD Main Menu 1 Mounting 2 Autostart 3 Valve Action Press keys (UP)+(DOWN) simultaneously to enter menu ‘Autostart’. Select Full or Short autostart* by pressing (UP) or (DOWN). Press keys (UP)+(DOWN) simultaneously to enter menu ‘Autostart’. Select Full or Short autostart* by pressing (UP) or (DOWN). Full autostart 2 Autostart 2.1 Full 2.2 Short Short autostart Press keys (UP)+(DOWN) simultaneously to confirm and to launch Autostart. The automatic adaption to the valve is composed of a sequence of steps, explained on the display. Press keys (UP)+(DOWN) simultaneously to confirm and to launch Autostart. The automatic adaption to the valve is composed of 4 steps (this is shown by LEDs ‘1’ to ‘4’ lighting up in sequence). Following the last step, the device is IN OPERATION.– Following the last step, all the LEDs go out and the device is IN OPERATION.– *) Short autostart determines only the mechanical stops of actuator/valve QG EVE0105 (en) SRD991 7 Menustructure for SRD991/SRD960 with LCD SRD Main Menu Menu Factory Description configuration 1 Mounting 1.1 Lin left 9 Linear actuator, left-hand or direct mounting 1.2 Lin right Linear actuator, right-hand mounting 1.3 Rot cclockw Rotary actuator, opening counter-clockwise 1.4 Rot clockw Rotary actuator, opening clockwise 2 Autostart 2.1 Full Autostart for the full adaptation / start-up 2.2 Short Short Autostart for the adaptation / start-up of the mechanical stops only 3 Valve Action 3.1 Direct 9 Valve opens with increasing setpoint value 3.2 Reverse Valve closes with increasing setpoint value 4 Character 4.1 Linear 9 Linear characteristic 4.2 Eq Perc 1:50 Equal percentage characteristic 1:50 4.3 Quick open Inverse equal percentage characteristic 1:50 (quick opening) 4.4 Customer Custom characteristic 5 Limits/alarms Not locally available with LED versions of communication FF and Profibus 5.1 Lower limit 0 % Closing limit is set to input value 5.2 Cutoff low 1 % 0%-tight sealing point is set to input value 5.3 Cutoff high 100 % 100%-tight sealing point is set to input value 5.4 Upper limit 100 % Opening limit is set to input value 5.5 Splitr 0 % 4 mA Split range 0 %: input value corresponds to 0 % 5.6 Splitr 100 % 20 mA Split range 100 %: input value corresponds to 100 % 5.7 Lower Alarm -10 % Lower position alarm on output 1 is set to input value 5.8 Upper Alarm 110 % Upper position alarm on output 2 is set to input value 5.9 Valve 0% 4 mA Configuration of rated-stroke of 0% at 4 mA 5.10 Valve 100% 20 mA Configuration of rated-stroke of 100% at 20 mA 5.11 Stroke Range x° / 20mm Configuration of nominal travel 6 Parameters 6.1 Gain closing 15 P: Proportional gain for ‘close valve’ 6.2 Gain closing 2 p: Proportional gain for ‘open valve’ 6.3 Res time cl 7.5 I: Integration time for ‘close valve’ 6.4 Res time op 2.4 I: Integration time for ‘open valve’ 6.5 Rate lim cl 0.35 T63: Setting time for ‘close valve’ 6.6 Rate lim op 0.35 T63: Setting time for ‘open valve’ 6.7 Control gap 0.1 Permitted neutral zone for control difference 7 Output Manual setting of IP-Module for testing of pneumatic output 8 Setpoint Manual setting of valve position Continue on the next page... 8 SRD991 QG EVE0105-(en) 9 Workbench 9.1 Reset Config Resetting of configuration to setting “ex factory” 9.2 Calib. 4 mA Calibrate input current to 4 mA 9.3 Calib. 20 mA Calibrate input current to 20 mA 9.4 Calib. -45° Calibrate position measuring value to –45° 9.5 Calib.
本文档为【SRD991智能定位器使用手册】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑, 图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。
下载需要: 免费 已有0 人下载
最新资料
资料动态
专题动态
is_292767
暂无简介~
格式:pdf
大小:1MB
软件:PDF阅读器
页数:20
分类:生产制造
上传时间:2011-01-11
浏览量:212