首页 Final Sound技术优势分析

Final Sound技术优势分析

举报
开通vip

Final Sound技术优势分析 The Inverter Principle for Electrostatic Loudspeakers Introduction Electrostatic speaker systems have been considered the absolute state of the art in audio reproduction since the 1960’s, when the legendary KLH 9 first made its debut. Shortly after, Infin...

Final Sound技术优势分析
The Inverter Principle for Electrostatic Loudspeakers Introduction Electrostatic speaker systems have been considered the absolute state of the art in audio reproduction since the 1960’s, when the legendary KLH 9 first made its debut. Shortly after, Infinity Systems introduced the Servo Static One, a full range electrostatic design that was considered the best speaker of all time and led to Infinity’s current position as one of the leading speaker brands in the world. In the early 1990’s, Martin Logan popularized the concept of “hybridization”, the process of blending dynamic and electrostatic technologies to deal with some of the technological difficulties of electrostatic loudspeakers. Electrostatic speakers are known for there clarity and transparency of sound, as well for the low distortion because amongst others the very low mass of the moving diaphragm. Besides the very high sound quality, traditional electrostatic speakers had also a number of principle disadvantages such as a very low impedance as soon as the frequency goes above 1000hz even as low as 1Ohm(need for expensive and powerful amplifiers). Another known disadvantage for traditional electrostatic speakers is the beamy pattern of the sound distribution resulting in a narrow spot of the listening place. Because of the very principle of the sound reproduction, electrostatic speakers need very large surfaces to reproduce Bass tones (expensive) In case of a traditional electrostatic loudspeaker elements a thin film, permanently charged by means of a high voltage , is suspended between two perforated plates. The audio signal from the amplifier is transformed into a high voltage by means of an audio transformer and delivered to the perforated plates as an alternating current. The alternating electrical field caused by the two perforated plates (the stators) will push and pull the film (the membrane). The membrane itself will move the air and therefore produce sound waves. The Final Sound Inverter’s unique selling points Low distortion Transparency and life-like sound High-definition sound (a lot of detail) High Impedance resulting in lower power and lower-cost amplifiers Broad Stereo Image Excellent sensitivity on normal listening distance Much less affected by room reflections (against walls, ceiling and floor) resulting in a lower-cost for the Home Theatre Installation. The Inverter principle results in a high degree of safety allowing the design to comply with the UL and CE requirements The Inverter also needs smaller electronics, resulting in a flat and digital lifestyle design. Final Sound Solutions modular design allows applying manufacturing technologies that allow for much lower manufacturing cost prices and as such more attractive end-user prices. • • • • • • • • • The Inverter Principle for Electrostatic Loudspeakers The inverter: the Final Sound solution Final Sound developed the Inverter Electrostat over the last two years in order to solve a number of the disadvantages of electrostats while keeping the benefits. Additionally FSS has improved the diaphragm technology substantially, so it will last much longer than traditional electrostats. audio signal diaphragm stator plates The Inverter Principle for Electrostatic Loudspeakers The Inverter Principle for Electrostatic Loudspeakers The Final Sound electrostatic concept The Final electrostatic loudspeakers consist of the following basic components: The electrostatic transducer. This element is a sandwich of two perforated plates. In between these plates a thin film (the membrane) is suspended. The plates are coated with special epoxy polyester to obtain a proper insulation. The membrane is made electrically conductive by means of a coating process. Final uses VHB (very high bonding) tapes to build the sandwiches. The audio transformer. Final has developed its own state of the art audio transformers. Special core materials and insulation techniques are applied. The audio transformer is for a major part responsible for the performance of the speaker. On today’s market suitable audio transformers for electrostatic panels are not available. The high-voltage unit. A high voltage unit powers each electrostatic element. This unit delivers the polarization voltage to the membrane. The power consumption of the electrostatic loudspeakers is very low. Also here Final Sound developed it’s own patented technology. The frame. The electrostatic elements are fixed in a rigid framework. The newest generation Final speakers have a beautiful framework made of extruded alloy tubes. The satin finished framework gives the speaker a unique cool look. Final sound also can deliver any RAL color as an option. On the other hand the extrusion profiles enable large volume production. A unique feature of the HT systems is that the electrostatic panels can be delivered in a wall- mounted version and a floor standing version. Its unique technology of electrostatic speakers allows a superb sound quality combined with an excellent price /performance ratio. Its extreme flat design allows not only floor standing but also wall mounting. Its patent protected and patent pending electrostatic technology allows a far better price performance than competing systems Why does an electrostatic loudspeaker (ESL) sound louder? When characterizing the sensitivity of loudspeakers in general it is common practice to express this magnitude in dB/1 meter/1 watt or 2,83 volts. This works fine as a measure for dynamic speakers as these are point sources, but asks for some more detailed explanation for line sources. Final Sound electrostatic loudspeakers are line sources and also dipoles. Both aspects will be treated here. A conventional cone-type loudspeaker is a point source, moreover it usually only radiates in the forward direction. A Final electrostatic panel is a line source and it radiates as much at the front as at the rear. The Inverter Principle for Electrostatic Loudspeakers When a long line source is measured at 1-meter distance, the microphone usually receives its sound from a limited part of the total sounding surface. Therefore the figures obtained by such a measurement do not rightly reflect the listener’s impression of the sound level. Acoustical theory shows that the sound level of a point source diminishes –naturally- with 6 dB per doubling of the measuring distance, while long line sources like Final electrostats show a decrease of 3dB per doubling of the distance. When seated at a distance of typically 4 meters in a room, the sound intensity out of a point source is 12 dB lower than at the usual but not very practical measuring distance of 1 meter. From a line source like a large electrostatic loudspeaker, when auditioned at 4 meters, the loss is not 12dB but 6 dB only. An example may clarify this phenomenon: A good cones loudspeaker, behaving as a point source has a “sensitivity of 86dB/watt/1 meter”. At the usual 4- meter distant listening position, the sound level has dropped to 86-12 = 74 dB. A big ESL, when auditioned at the same distance will produce a sound level of 86-6=80dB. A 6 dB difference. The second property of ESL’s is its dipole character. A conventional speaker only radiates to the front, as the back is usually closed by the box. An ESL radiates its sound energy both to the front as to the rear and this rear sound energy will be reflected to the walls and added to the waves coming from the front. This will contribute to the overall sound level impression of the listener. Were these two waves in phase, it would lead to an increase of 6dB. But generally this is not the case of course. An estimation of a 3dB difference is realistic. Let us sit down again at our listening position at 4 meters of our 86dB/1meter/1watt loudspeaker and add the two phenomena as described above together. The point source will yield (see above) a sound level of 86-12=74 dB at 4 meters distance. This is an important 9 dB of difference at the listening position. Smaller ESL’s are not an ideal line source, but still are dipoles with their 3 dB advantage. A smaller ESL/86dB in this context, will yield a sound level at 4 meters of some 86-9+3 dB = 80dB, still 6dB ahead of a point source with the same measured 86db/1 meter/ 1 watt/2,83 volts. When Final specifies 86dB/1 meter/1 watt, it is measured with the standardized method. For large ESL’s one has to add 9db to that figure: it effectively becomes 95 dB equivalent as compared to a point source: a normal cone loudspeaker. For small ESL’s one has to add 6dB to that figure: this effectively becomes 92dB equivalent in order to get the right impression of the capabilities of ESL’s versus cone loudspeakers. The last pitfall in interpreting the measurement results of ESL’s, has –again- to do with its long, mostly vertical- dimensions. The Inverter Principle for Electrostatic Loudspeakers When assessing the frequency characteristic at the usual distance of 1 meter, there maybe considerable differences in distances between the microphone and the different parts of the ESL: from the middle the distance, of course, is 1 meter. But from the extremities of a 56 cm high ESL the distance is, Root ( 100^2+26^2) = 103,9 cm. This is a half wavelength at approx. 4000 Hz. At this frequency the waves from the extremes of the ESL will more or less cancel out the waves emanating from the centre. The curve will lead an uninformed experimenter to believe that the frequency characteristic falls with 3 dB per octave beyond this first cancellation frequency! Measuring however at 4-meter distance, this first canceling-frequency will be at 16000 Hz. A 120 cm long ESL like the FINAL model 400 will experience its “first cancellation frequency” at around 3600 Hz. For a listener in a room with some reverberation –not being a “dead” room- this phenomenon is quite unimportant, as all waves coming back to him from all walls and the floor and ceiling will smooth out the undulations experienced in the measuring set-up in a non-reverberating room with software canceling all reflections. When judging the measurements of an ESL in a non-reverberating set-up, one can, for a quick assessment of the qualities of an ESL, accept the following rules: measuring the behavior at low frequencies can be done at the usual 1 meter distance, high frequencies can best be measured at a distance of 4 meter or more. Electrostatic versus dynamic loudspeaker Comparisons between electrostatic (ESL) and dynamic (Cones) loudspeakers and descriptions of the operation of ESL’s have been made in all shapes and forms, enough to fill a small library. So this introduction is limited to a short enumeration of the most salient differences between the two systems, hoping this subject is well known to readers. Electromagnetic or dynamic loudspeakers have cones driven by some form of a coil moving in a magnetic field –flat or circular. These cones are usually excited at the center for bass and middle tone speakers or at the perimeter in the case of tweeters and are hoped to move exactly in accordance with the electrical current through the coil. In practice however, cones move more or less like shaking a rug, than like an ideal stiff surface. See the diagram below just to excite your imagination. One may hope the mean value of the movement over the total surface is neat enough to give an acceptable and musical representation of our beloved sound material. • The Inverter Principle for Electrostatic Loudspeakers ESL diaphragms have considerably less weight than cones: the diaphragm of an 90i weighs less than 1 gram. As much as 100 liter of air weighing 1 kg per m3. In an ESL such a diaphragm is 12 micron thick and it weighs as little as a layer of air of 12 mm thick: 6 mm on both sides. In an ESL the diaphragm is driven simultaneously and homogeneously over the entire surface. Dampened as it is by its surrounding air this thin and ultra light foil does not get the tiniest chance to invent movements of its own. Cones have the advantage of a long stroke, so the surface of an ESL diaphragm should be many times larger than that of a cone to move the same number of air molecules. But be aware: the ESL moves air at both sides as explained above. Low frequency output from ESL’s is admittedly nice and clean, but usually no too strong, unless the ESL’s surface is huge and at the same token it gets quite expensive. Final’s finest model 1.4, now baptized 1400i, has a surface per loudspeaker of 0,54 square meters. If this were a round cone it’s radiating diameter should be 95cm or 37 inch! Our smallest model (model 90) today has one tenth of the surface of the 1000 and that is 0,07 square meter. Its equivalent diameter should be 12 inch, still the measurement of a very respectable cone-speaker. Dynamic loudspeakers are usually housed in not dumb-and-dead boxes, which –these boxes too, alas- have their own contribution to the sound of music. ESL’s have no such boxes, at the expense of the performance in the bass frequencies. Dynamic loudspeakers require the frequency spectrum to be divided into two, three or more sub-bands. This brings about the use of LC-filters with their own influence on the sound. ESL’s, due to their large radiating surface, tend to exhibit bundling of the higher end of the audio spectrum, reducing the dimensions of the so-called sweet spot. FINAL has found out how to fight this phenomenon. Most ESL’s on the market require high end amplifiers because of their weird impedance over frequency: values can be found as low as 1 ohm at 20kHz. And very capacitive too as this 1 ohm is the equivalent of 8 microfarad. This in itself is a strange phenomenon because theoretically the sensitivity of an ESL increases with frequency and one would, based on electrical energy in versus audio energy out, expect some sort of inverse behavior. Full range electrostatic loudspeakers usually have a limited sensitivity. 86 dB is commonly found whereas dynamic loudspeakers exhibit sensitivity more like 86 to 92 dB without recurring the use of exponential horns and other additional means (measured at 2,83 volt in and at a distance of 1 meter). This has been discussed thoroughly above. The sound is louder than you would conclude from the specs. • • • • • • • • The Inverter Principle for Electrostatic Loudspeakers Full range electrostatic loudspeakers usually have a limited sensitivity. 86 dB is commonly found whereas dynamic loudspeakers exhibit sensitivity more like 86 to 92 dB without recurring the use of exponential horns and other additional means (measured at 2,83 volt in and at a distance of 1 meter). This has been discussed thoroughly above. The sound is louder than you would conclude from the specs. The industry in the past decennia has predominantly made large and expensive Electrostatic Loudspeakers in rather small quantities mainly for the high-end market, and not yet addressed the middle segment. Part of this is due to a vicious circle whereas small quantities do not lead to a quick decrease of the cost of manufacturing, nor a quick run down the learning curve. Dynamic loudspeakers on the contrary, are made in huge quantities and varieties worldwide and so are cheaply available. The application of the high voltages necessary in an ESL presents a challenge as to the safety as laid down for instance in ETL and UL-requirements related to human safety and fire hazard. Finals Inverter solution has solved this. ESL’s are sensitive to dust, smoke and moisture: these particles tend to shorten their lifetime. However Final has developed a new type of diaphragm with a protective coating to enable a long lifetime. Nevertheless, it’s recommended to clean the panels ate least once a quarter, using a vacuum cleaner. ESL’s are line sources and so behave in a completely different manner as point sources in the build-up of the acoustic field. • • • • •
本文档为【Final Sound技术优势分析】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑, 图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。
下载需要: 免费 已有0 人下载
最新资料
资料动态
专题动态
is_080152
暂无简介~
格式:pdf
大小:1014KB
软件:PDF阅读器
页数:8
分类:生活休闲
上传时间:2010-12-02
浏览量:32